Update ampel-firmware/config.public.h, .gitlab-ci.yml files

This commit is contained in:
Dorian Zedler 2021-05-09 19:05:35 +00:00
parent 9c8e7f9a17
commit 7dc2baab1f
2 changed files with 155 additions and 2 deletions

View File

@ -4,9 +4,8 @@ stages:
- build
before_script:
- "cd firmware"
- "pip install -U platformio"
# - "cp ampel-firmware/config.public.h ampel-firmware/config.h"
- "cp ampel-firmware/config.public.h ampel-firmware/config.h"
job:
stage: build

View File

@ -0,0 +1,154 @@
#ifndef CONFIG_H_INCLUDED
# define CONFIG_H_INCLUDED
// This file is a config template, and can be copied to config.h. Please don't save any important password in this template.
/**
* SERVICES
*/
// Comment or remove those lines if you want to disable the corresponding services
# define AMPEL_WIFI // Should ESP connect to WiFi? It allows the Ampel to get time from an NTP server.
# define AMPEL_HTTP // Should HTTP web server be started? (AMPEL_WIFI should be enabled too)
# define AMPEL_MQTT // Should data be sent over MQTT? (AMPEL_WIFI should be enabled too)
# define AMPEL_CSV // Should data be logged as CSV, on the ESP flash memory?
// # define AMPEL_LORAWAN // Should data be sent over LoRaWAN? (Requires ESP32 + LoRa modem, and "MCCI LoRaWAN LMIC library")
/**
* WIFI
*/
# define WIFI_SSID "MY_SSID"
# define WIFI_PASSWORD "P4SSW0RD"
# define WIFI_TIMEOUT 30 // [s]
/**
* Sensor
*/
// How often should measurement be performed, and displayed?
//NOTE: SCD30 timer does not seem to be very precise. Variations may occur.
# define MEASUREMENT_TIMESTEP 60 // [s] Value between 2 and 1800 (range for SCD30 sensor)
// How often should measurements be appended to CSV ?
// Probably a good idea to use a multiple of MEASUREMENT_TIMESTEP, so that averages can be calculated
// Set to 0 if you want to send values after each measurement
// WARNING: Writing too often might damage the ESP memory
# define CSV_INTERVAL 300 // [s]
// Residual heat from CO2 sensor seems to be high enough to change the temperature reading. How much should it be offset?
// NOTE: Sign isn't relevant. The returned temperature will always be shifted down.
# define TEMPERATURE_OFFSET -3 // [K]
// Altitude above sea level
// Used for CO2 calibration
// here: Stuttgart, Schellingstr. 24. (Source: Google Earth)
# define ALTITUDE_ABOVE_SEA_LEVEL 260 // [m]
// The reference CO2 concentration has to be within the range 400 ppm ≤ cref(CO2) ≤ 2000 ppm.
// Used for CO2 calibration
// here : measured concentration in Stuttgart
# define ATMOSPHERIC_CO2_CONCENTRATION 425 // [ppm]
// Should the sensor try to calibrate itself?
// Sensirion recommends 7 days of continuous readings with at least 1 hour a day of 'fresh air' for self-calibration to complete.
# define AUTO_CALIBRATE_SENSOR true // [true / false]
/**
* LEDs
*/
// LED brightness, which can vary between min and max brightness ("LED breathing")
// MAX_BRIGHTNESS must be defined, and should be between 0 and 255.
# define MAX_BRIGHTNESS 255
// MIN_BRIGHTNESS, if defined, should be between 0 and MAX_BRIGHTNESS - 1
// If MIN_BRIGHTNESS is not set, or if it is set to MAX_BRIGHTNESS, breathing is disabled.
# define MIN_BRIGHTNESS 60
/**
* WEB SERVER
* available at http://local_ip, with user HTTP_USER and password HTTP_PASSWORD
*/
// Define empty strings in order to disable authentication, or remove the constants altogether.
# define HTTP_USER "co2ampel"
# define HTTP_PASSWORD "my_password"
/**
* MQTT
*/
/*
* If AMPEL_MQTT is enabled, co2ampel will publish data every MQTT_SENDING_INTERVAL seconds.
* An MQTT subscriber can then get the data from the corresponding broker, either encrypted or unencrypted:
*
* mosquitto_sub -h 'test.mosquitto.org' -p 8883 -t 'CO2sensors/#' --cafile mosquitto.org.crt -v
* CO2sensors/ESPd03cc5 {"time":"2020-12-13 13:14:37+01", "co2":571, "temp":18.9, "rh":50.9}
* CO2sensors/ESPd03cc5 {"time":"2020-12-13 13:14:48+01", "co2":573, "temp":18.9, "rh":50.2}
* ...
*
* mosquitto_sub -h 'test.mosquitto.org' -t 'CO2sensors/#' -v
* CO2sensors/ESPd03cc5 {"time":"2020-12-13 13:15:09+01", "co2":568, "temp":18.9, "rh":50.1}
* CO2sensors/ESPd03cc5 {"time":"2020-12-13 13:15:20+01", "co2":572, "temp":18.9, "rh":50.3}
* ...
*/
/*
* Allow sensor to be configured over MQTT? Very useful for debugging. For example:
* mosquitto_pub -h 'test.mosquitto.org' -t 'CO2sensors/ESPe08dc9/control' -m 'timer 30'
* mosquitto_pub -h 'test.mosquitto.org' -t 'CO2sensors/ESPe08dc9/control' -m 'calibrate'
* mosquitto_pub -h 'test.mosquitto.org' -t 'CO2sensors/ESPe08dc9/control' -m 'reset'
*/
# define ALLOW_MQTT_COMMANDS false
// How often measurements should be sent to MQTT server?
// Probably a good idea to use a multiple of MEASUREMENT_TIMESTEP, so that averages can be calculated
// Set to 0 if you want to send values after each measurement
// # define MQTT_SENDING_INTERVAL MEASUREMENT_TIMESTEP * 5 // [s]
# define MQTT_SENDING_INTERVAL 60 // [s]
# define MQTT_SERVER "test.mosquitto.org" // MQTT server URL or IP address
# define MQTT_PORT 8883
# define MQTT_USER ""
# define MQTT_PASSWORD ""
/**
* LoRaWAN
*/
// 1) Requires "MCCI LoRaWAN LMIC library", which will be automatically used with PlatformIO but should be added in "Arduino IDE".
// 2) Region and transceiver type should be specified in:
// * Arduino/libraries/MCCI_LoRaWAN_LMIC_library/project_config/lmic_project_config.h for Arduino IDE
// * platformio.ini for PlatformIO
// See https://github.com/mcci-catena/arduino-lmic#configuration for more information
// 3) It has been tested with "TTGO ESP32 SX1276 LoRa 868" and will only work with an ESP32 + LoRa modem
// 4) In order to use LoRaWAN, a gateway should be close to the co2ampel, and an account, an application and a device should be registered,
// e.g. on https://www.thethingsnetwork.org/docs/applications/
// 5) The corresponding keys should be defined in LORAWAN_DEVICE_EUI, LORAWAN_APPLICATION_EUI and LORAWAN_APPLICATION_KEY
// How often should measurements be sent over LoRaWAN?
# define LORAWAN_SENDING_INTERVAL 300 // [s] This value should not be too low. See https://www.thethingsnetwork.org/docs/lorawan/duty-cycle.html#maximum-duty-cycle
// WARNING: If AMPEL_LORAWAN is enabled, you need to modify the 3 following constants!
// This EUI must be in little-endian format, so least-significant-byte first.
// When copying an EUI from ttnctl output, this means to reverse the bytes.
# define LORAWAN_DEVICE_EUI {0x88, 0x77, 0x66, 0x55, 0x44, 0x33, 0x22, 0x11}
// This should also be in little endian format, see above.
// For TheThingsNetwork issued EUIs the last bytes should be 0xD5, 0xB3, 0x70.
# define LORAWAN_APPLICATION_EUI {0x00, 0x00, 0x00, 0x00, 0x00, 0xD5, 0xB3, 0x70}
// This key should be in big endian format (or, since it is not really a
// number but a block of memory, endianness does not really apply). In
// practice, a key taken from ttnctl can be copied as-is.
# define LORAWAN_APPLICATION_KEY {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 }
/**
* NTP
*/
# define NTP_SERVER "pool.ntp.org"
# define UTC_OFFSET_IN_SECONDS 7200 // [s] 3600 for UTC+1, 7200 for UTC+1 and daylight saving time
/**
* Others
*/
# define BAUDS 115200 // Transmission rate
#endif // CONFIG_H_INCLUDED