/** @file

  This file contains the register definition of XHCI host controller.

Copyright (c) 2011 - 2018, Intel Corporation. All rights reserved.<BR>
SPDX-License-Identifier: BSD-2-Clause-Patent

**/

#ifndef _EFI_XHCI_REG_H_
#define _EFI_XHCI_REG_H_

#define PCI_IF_XHCI  0x30

//
// PCI Configuration Registers
//
#define XHC_BAR_INDEX  0x00

#define XHC_PCI_BAR_OFFSET  0x10               // Memory Bar Register Offset
#define XHC_PCI_BAR_MASK    0xFFFF             // Memory Base Address Mask

#define XHC_PCI_SBRN_OFFSET  0x60              // Serial Bus Release Number Register Offset

#define USB_HUB_CLASS_CODE     0x09
#define USB_HUB_SUBCLASS_CODE  0x00

#define XHC_CAP_USB_LEGACY              0x01
#define XHC_CAP_USB_DEBUG               0x0A
#define XHC_CAP_USB_SUPPORTED_PROTOCOL  0x02

// ============================================//
//           XHCI register offset             //
// ============================================//

//
// Capability registers offset
//
#define XHC_CAPLENGTH_OFFSET   0x00             // Capability register length offset
#define XHC_HCIVERSION_OFFSET  0x02             // Interface Version Number 02-03h
#define XHC_HCSPARAMS1_OFFSET  0x04             // Structural Parameters 1
#define XHC_HCSPARAMS2_OFFSET  0x08             // Structural Parameters 2
#define XHC_HCSPARAMS3_OFFSET  0x0c             // Structural Parameters 3
#define XHC_HCCPARAMS_OFFSET   0x10             // Capability Parameters
#define XHC_DBOFF_OFFSET       0x14             // Doorbell Offset
#define XHC_RTSOFF_OFFSET      0x18             // Runtime Register Space Offset

//
// Operational registers offset
//
#define XHC_USBCMD_OFFSET    0x0000               // USB Command Register Offset
#define XHC_USBSTS_OFFSET    0x0004               // USB Status Register Offset
#define XHC_PAGESIZE_OFFSET  0x0008               // USB Page Size Register Offset
#define XHC_DNCTRL_OFFSET    0x0014               // Device Notification Control Register Offset
#define XHC_CRCR_OFFSET      0x0018               // Command Ring Control Register Offset
#define XHC_DCBAAP_OFFSET    0x0030               // Device Context Base Address Array Pointer Register Offset
#define XHC_CONFIG_OFFSET    0x0038               // Configure Register Offset
#define XHC_PORTSC_OFFSET    0x0400               // Port Status and Control Register Offset

//
// Runtime registers offset
//
#define XHC_MFINDEX_OFFSET  0x00                // Microframe Index Register Offset
#define XHC_IMAN_OFFSET     0x20                // Interrupter X Management Register Offset
#define XHC_IMOD_OFFSET     0x24                // Interrupter X Moderation Register Offset
#define XHC_ERSTSZ_OFFSET   0x28                // Event Ring Segment Table Size Register Offset
#define XHC_ERSTBA_OFFSET   0x30                // Event Ring Segment Table Base Address Register Offset
#define XHC_ERDP_OFFSET     0x38                // Event Ring Dequeue Pointer Register Offset

//
// Debug registers offset
//
#define XHC_DC_DCCTRL  0x20

#define USBLEGSP_BIOS_SEMAPHORE  BIT16           // HC BIOS Owned Semaphore
#define USBLEGSP_OS_SEMAPHORE    BIT24           // HC OS Owned Semaphore

//
// xHCI Supported Protocol Capability
//
#define XHC_SUPPORTED_PROTOCOL_DW0_MAJOR_REVISION_USB2  0x02
#define XHC_SUPPORTED_PROTOCOL_DW0_MAJOR_REVISION_USB3  0x03
#define XHC_SUPPORTED_PROTOCOL_NAME_STRING_OFFSET       0x04
#define XHC_SUPPORTED_PROTOCOL_NAME_STRING_VALUE        0x20425355
#define XHC_SUPPORTED_PROTOCOL_DW2_OFFSET               0x08
#define XHC_SUPPORTED_PROTOCOL_PSI_OFFSET               0x10
#define XHC_SUPPORTED_PROTOCOL_USB2_HIGH_SPEED_PSIM     480
#define XHC_SUPPORTED_PROTOCOL_USB2_LOW_SPEED_PSIM      1500

#pragma pack (1)
typedef struct {
  UINT8     MaxSlots;                     // Number of Device Slots
  UINT16    MaxIntrs : 11;                // Number of Interrupters
  UINT16    Rsvd     : 5;
  UINT8     MaxPorts;                     // Number of Ports
} HCSPARAMS1;

//
// Structural Parameters 1 Register Bitmap Definition
//
typedef union {
  UINT32        Dword;
  HCSPARAMS1    Data;
} XHC_HCSPARAMS1;

typedef struct {
  UINT32    Ist          : 4;             // Isochronous Scheduling Threshold
  UINT32    Erst         : 4;             // Event Ring Segment Table Max
  UINT32    Rsvd         : 13;
  UINT32    ScratchBufHi : 5;             // Max Scratchpad Buffers Hi
  UINT32    Spr          : 1;             // Scratchpad Restore
  UINT32    ScratchBufLo : 5;             // Max Scratchpad Buffers Lo
} HCSPARAMS2;

//
// Structural Parameters 2 Register Bitmap Definition
//
typedef union {
  UINT32        Dword;
  HCSPARAMS2    Data;
} XHC_HCSPARAMS2;

typedef struct {
  UINT16    Ac64       : 1;              // 64-bit Addressing Capability
  UINT16    Bnc        : 1;              // BW Negotiation Capability
  UINT16    Csz        : 1;              // Context Size
  UINT16    Ppc        : 1;              // Port Power Control
  UINT16    Pind       : 1;              // Port Indicators
  UINT16    Lhrc       : 1;              // Light HC Reset Capability
  UINT16    Ltc        : 1;              // Latency Tolerance Messaging Capability
  UINT16    Nss        : 1;              // No Secondary SID Support
  UINT16    Pae        : 1;              // Parse All Event Data
  UINT16    Rsvd       : 3;
  UINT16    MaxPsaSize : 4;              // Maximum Primary Stream Array Size
  UINT16    ExtCapReg;                   // xHCI Extended Capabilities Pointer
} HCCPARAMS;

//
// Capability Parameters Register Bitmap Definition
//
typedef union {
  UINT32       Dword;
  HCCPARAMS    Data;
} XHC_HCCPARAMS;

//
// xHCI Supported Protocol Cabability
//
typedef struct {
  UINT8    CapId;
  UINT8    NextExtCapReg;
  UINT8    RevMinor;
  UINT8    RevMajor;
} SUPPORTED_PROTOCOL_DW0;

typedef union {
  UINT32                    Dword;
  SUPPORTED_PROTOCOL_DW0    Data;
} XHC_SUPPORTED_PROTOCOL_DW0;

typedef struct {
  UINT32    NameString;
} XHC_SUPPORTED_PROTOCOL_DW1;

typedef struct {
  UINT8     CompPortOffset;
  UINT8     CompPortCount;
  UINT16    ProtocolDef : 12;
  UINT16    Psic        : 4;
} SUPPORTED_PROTOCOL_DW2;

typedef union {
  UINT32                    Dword;
  SUPPORTED_PROTOCOL_DW2    Data;
} XHC_SUPPORTED_PROTOCOL_DW2;

typedef struct {
  UINT16    Psiv  : 4;
  UINT16    Psie  : 2;
  UINT16    Plt   : 2;
  UINT16    Pfd   : 1;
  UINT16    RsvdP : 5;
  UINT16    Lp    : 2;
  UINT16    Psim;
} SUPPORTED_PROTOCOL_PROTOCOL_SPEED_ID;

typedef union {
  UINT32                                  Dword;
  SUPPORTED_PROTOCOL_PROTOCOL_SPEED_ID    Data;
} XHC_SUPPORTED_PROTOCOL_PROTOCOL_SPEED_ID;

#pragma pack ()

//
// Register Bit Definition
//
#define XHC_USBCMD_RUN    BIT0                   // Run/Stop
#define XHC_USBCMD_RESET  BIT1                   // Host Controller Reset
#define XHC_USBCMD_INTE   BIT2                   // Interrupter Enable
#define XHC_USBCMD_HSEE   BIT3                   // Host System Error Enable

#define XHC_USBSTS_HALT  BIT0                    // Host Controller Halted
#define XHC_USBSTS_HSE   BIT2                    // Host System Error
#define XHC_USBSTS_EINT  BIT3                    // Event Interrupt
#define XHC_USBSTS_PCD   BIT4                    // Port Change Detect
#define XHC_USBSTS_SSS   BIT8                    // Save State Status
#define XHC_USBSTS_RSS   BIT9                    // Restore State Status
#define XHC_USBSTS_SRE   BIT10                   // Save/Restore Error
#define XHC_USBSTS_CNR   BIT11                   // Host Controller Not Ready
#define XHC_USBSTS_HCE   BIT12                   // Host Controller Error

#define XHC_PAGESIZE_MASK  0xFFFF                 // Page Size

#define XHC_CRCR_RCS  BIT0                       // Ring Cycle State
#define XHC_CRCR_CS   BIT1                       // Command Stop
#define XHC_CRCR_CA   BIT2                       // Command Abort
#define XHC_CRCR_CRR  BIT3                       // Command Ring Running

#define XHC_CONFIG_MASK  0xFF                    // Command Ring Running

#define XHC_PORTSC_CCS    BIT0                      // Current Connect Status
#define XHC_PORTSC_PED    BIT1                      // Port Enabled/Disabled
#define XHC_PORTSC_OCA    BIT3                      // Over-current Active
#define XHC_PORTSC_RESET  BIT4                      // Port Reset
#define XHC_PORTSC_PLS    (BIT5|BIT6|BIT7|BIT8)     // Port Link State
#define XHC_PORTSC_PP     BIT9                      // Port Power
#define XHC_PORTSC_PS     (BIT10|BIT11|BIT12|BIT13) // Port Speed
#define XHC_PORTSC_LWS    BIT16                     // Port Link State Write Strobe
#define XHC_PORTSC_CSC    BIT17                     // Connect Status Change
#define XHC_PORTSC_PEC    BIT18                     // Port Enabled/Disabled Change
#define XHC_PORTSC_WRC    BIT19                     // Warm Port Reset Change
#define XHC_PORTSC_OCC    BIT20                     // Over-Current Change
#define XHC_PORTSC_PRC    BIT21                     // Port Reset Change
#define XHC_PORTSC_PLC    BIT22                     // Port Link State Change
#define XHC_PORTSC_CEC    BIT23                     // Port Config Error Change
#define XHC_PORTSC_CAS    BIT24                     // Cold Attach Status

#define XHC_HUB_PORTSC_CCS    BIT0               // Hub's Current Connect Status
#define XHC_HUB_PORTSC_PED    BIT1               // Hub's Port Enabled/Disabled
#define XHC_HUB_PORTSC_OCA    BIT3               // Hub's Over-current Active
#define XHC_HUB_PORTSC_RESET  BIT4               // Hub's Port Reset
#define XHC_HUB_PORTSC_PP     BIT9               // Hub's Port Power
#define XHC_HUB_PORTSC_CSC    BIT16              // Hub's Connect Status Change
#define XHC_HUB_PORTSC_PEC    BIT17              // Hub's Port Enabled/Disabled Change
#define XHC_HUB_PORTSC_OCC    BIT19              // Hub's Over-Current Change
#define XHC_HUB_PORTSC_PRC    BIT20              // Hub's Port Reset Change
#define XHC_HUB_PORTSC_BHRC   BIT21              // Hub's Port Warm Reset Change
#define XHC_IMAN_IP           BIT0               // Interrupt Pending
#define XHC_IMAN_IE           BIT1               // Interrupt Enable

#define XHC_IMODI_MASK  0x0000FFFF                     // Interrupt Moderation Interval
#define XHC_IMODC_MASK  0xFFFF0000                     // Interrupt Moderation Counter

//
//  Hub Class Feature Selector for Clear Port Feature Request
//  It's the extension of hub class feature selector of USB 2.0 in USB 3.0 Spec.
//  For more details, Please refer to USB 3.0 Spec Table 10-7.
//
typedef enum {
  Usb3PortBHPortReset       = 28,
  Usb3PortBHPortResetChange = 29
} XHC_PORT_FEATURE;

//
// Structure to map the hardware port states to the
// UEFI's port states.
//
typedef struct {
  UINT32    HwState;
  UINT16    UefiState;
} USB_PORT_STATE_MAP;

//
// Structure to map the hardware port states to feature selector for clear port feature request.
//
typedef struct {
  UINT32    HwState;
  UINT16    Selector;
} USB_CLEAR_PORT_MAP;

/**
  Read 1-byte width XHCI capability register.

  @param  Xhc          The XHCI Instance.
  @param  Offset       The offset of the 1-byte width capability register.

  @return The register content read.
  @retval If err, return 0xFFFF.

**/
UINT8
XhcReadCapReg8 (
  IN  USB_XHCI_INSTANCE  *Xhc,
  IN  UINT32             Offset
  );

/**
  Read 4-bytes width XHCI capability register.

  @param  Xhc          The XHCI Instance.
  @param  Offset       The offset of the 4-bytes width capability register.

  @return The register content read.
  @retval If err, return 0xFFFFFFFF.

**/
UINT32
XhcReadCapReg (
  IN  USB_XHCI_INSTANCE  *Xhc,
  IN  UINT32             Offset
  );

/**
  Read 4-bytes width XHCI Operational register.

  @param  Xhc          The XHCI Instance.
  @param  Offset       The offset of the 4-bytes width operational register.

  @return The register content read.
  @retval If err, return 0xFFFFFFFF.

**/
UINT32
XhcReadOpReg (
  IN  USB_XHCI_INSTANCE  *Xhc,
  IN  UINT32             Offset
  );

/**
  Write the data to the 4-bytes width XHCI operational register.

  @param  Xhc      The XHCI Instance.
  @param  Offset   The offset of the 4-bytes width operational register.
  @param  Data     The data to write.

**/
VOID
XhcWriteOpReg (
  IN USB_XHCI_INSTANCE  *Xhc,
  IN UINT32             Offset,
  IN UINT32             Data
  );

/**
  Read XHCI runtime register.

  @param  Xhc          The XHCI Instance.
  @param  Offset       The offset of the runtime register.

  @return The register content read

**/
UINT32
XhcReadRuntimeReg (
  IN  USB_XHCI_INSTANCE  *Xhc,
  IN  UINT32             Offset
  );

/**
  Write the data to the XHCI runtime register.

  @param  Xhc          The XHCI Instance.
  @param  Offset       The offset of the runtime register.
  @param  Data         The data to write.

**/
VOID
XhcWriteRuntimeReg (
  IN USB_XHCI_INSTANCE  *Xhc,
  IN UINT32             Offset,
  IN UINT32             Data
  );

/**
  Write the data to the XHCI door bell register.

  @param  Xhc          The XHCI Instance.
  @param  Offset       The offset of the door bell register.
  @param  Data         The data to write.

**/
VOID
XhcWriteDoorBellReg (
  IN USB_XHCI_INSTANCE  *Xhc,
  IN UINT32             Offset,
  IN UINT32             Data
  );

/**
  Set one bit of the operational register while keeping other bits.

  @param  Xhc          The XHCI Instance.
  @param  Offset       The offset of the operational register.
  @param  Bit          The bit mask of the register to set.

**/
VOID
XhcSetOpRegBit (
  IN USB_XHCI_INSTANCE  *Xhc,
  IN UINT32             Offset,
  IN UINT32             Bit
  );

/**
  Clear one bit of the operational register while keeping other bits.

  @param  Xhc          The XHCI Instance.
  @param  Offset       The offset of the operational register.
  @param  Bit          The bit mask of the register to clear.

**/
VOID
XhcClearOpRegBit (
  IN USB_XHCI_INSTANCE  *Xhc,
  IN UINT32             Offset,
  IN UINT32             Bit
  );

/**
  Wait the operation register's bit as specified by Bit
  to be set (or clear).

  @param  Xhc          The XHCI Instance.
  @param  Offset       The offset of the operational register.
  @param  Bit          The bit of the register to wait for.
  @param  WaitToSet    Wait the bit to set or clear.
  @param  Timeout      The time to wait before abort (in millisecond, ms).

  @retval EFI_SUCCESS  The bit successfully changed by host controller.
  @retval EFI_TIMEOUT  The time out occurred.

**/
EFI_STATUS
XhcWaitOpRegBit (
  IN USB_XHCI_INSTANCE  *Xhc,
  IN UINT32             Offset,
  IN UINT32             Bit,
  IN BOOLEAN            WaitToSet,
  IN UINT32             Timeout
  );

/**
  Read XHCI runtime register.

  @param  Xhc          The XHCI Instance.
  @param  Offset       The offset of the runtime register.

  @return The register content read

**/
UINT32
XhcReadRuntimeReg (
  IN  USB_XHCI_INSTANCE  *Xhc,
  IN  UINT32             Offset
  );

/**
  Write the data to the XHCI runtime register.

  @param  Xhc          The XHCI Instance.
  @param  Offset       The offset of the runtime register.
  @param  Data         The data to write.

**/
VOID
XhcWriteRuntimeReg (
  IN USB_XHCI_INSTANCE  *Xhc,
  IN UINT32             Offset,
  IN UINT32             Data
  );

/**
  Set one bit of the runtime register while keeping other bits.

  @param  Xhc          The XHCI Instance.
  @param  Offset       The offset of the runtime register.
  @param  Bit          The bit mask of the register to set.

**/
VOID
XhcSetRuntimeRegBit (
  IN USB_XHCI_INSTANCE  *Xhc,
  IN UINT32             Offset,
  IN UINT32             Bit
  );

/**
  Clear one bit of the runtime register while keeping other bits.

  @param  Xhc          The XHCI Instance.
  @param  Offset       The offset of the runtime register.
  @param  Bit          The bit mask of the register to set.

**/
VOID
XhcClearRuntimeRegBit (
  IN USB_XHCI_INSTANCE  *Xhc,
  IN UINT32             Offset,
  IN UINT32             Bit
  );

/**
  Read XHCI extended capability register.

  @param  Xhc          The XHCI Instance.
  @param  Offset       The offset of the extended capability register.

  @return The register content read

**/
UINT32
XhcReadExtCapReg (
  IN  USB_XHCI_INSTANCE  *Xhc,
  IN  UINT32             Offset
  );

/**
  Whether the XHCI host controller is halted.

  @param  Xhc     The XHCI Instance.

  @retval TRUE    The controller is halted.
  @retval FALSE   It isn't halted.

**/
BOOLEAN
XhcIsHalt (
  IN USB_XHCI_INSTANCE  *Xhc
  );

/**
  Whether system error occurred.

  @param  Xhc      The XHCI Instance.

  @retval TRUE     System error happened.
  @retval FALSE    No system error.

**/
BOOLEAN
XhcIsSysError (
  IN USB_XHCI_INSTANCE  *Xhc
  );

/**
  Reset the XHCI host controller.

  @param  Xhc          The XHCI Instance.
  @param  Timeout      Time to wait before abort (in millisecond, ms).

  @retval EFI_SUCCESS  The XHCI host controller is reset.
  @return Others       Failed to reset the XHCI before Timeout.

**/
EFI_STATUS
XhcResetHC (
  IN USB_XHCI_INSTANCE  *Xhc,
  IN UINT32             Timeout
  );

/**
  Halt the XHCI host controller.

  @param  Xhc          The XHCI Instance.
  @param  Timeout      Time to wait before abort (in millisecond, ms).

  @return EFI_SUCCESS  The XHCI host controller is halt.
  @return EFI_TIMEOUT  Failed to halt the XHCI before Timeout.

**/
EFI_STATUS
XhcHaltHC (
  IN USB_XHCI_INSTANCE  *Xhc,
  IN UINT32             Timeout
  );

/**
  Set the XHCI host controller to run.

  @param  Xhc          The XHCI Instance.
  @param  Timeout      Time to wait before abort (in millisecond, ms).

  @return EFI_SUCCESS  The XHCI host controller is running.
  @return EFI_TIMEOUT  Failed to set the XHCI to run before Timeout.

**/
EFI_STATUS
XhcRunHC (
  IN USB_XHCI_INSTANCE  *Xhc,
  IN UINT32             Timeout
  );

/**
  Calculate the offset of the XHCI capability.

  @param  Xhc     The XHCI Instance.
  @param  CapId   The XHCI Capability ID.

  @return The offset of XHCI legacy support capability register.

**/
UINT32
XhcGetCapabilityAddr (
  IN USB_XHCI_INSTANCE  *Xhc,
  IN UINT8              CapId
  );

/**
  Calculate the offset of the xHCI Supported Protocol Capability.

  @param  Xhc           The XHCI Instance.
  @param  MajorVersion  The USB Major Version in xHCI Support Protocol Capability Field

  @return The offset of xHCI Supported Protocol capability register.

**/
UINT32
XhcGetSupportedProtocolCapabilityAddr (
  IN USB_XHCI_INSTANCE  *Xhc,
  IN UINT8              MajorVersion
  );

/**
  Find SpeedField value match with Port Speed ID value.

  @param  Xhc    The XHCI Instance.
  @param  Speed  The Port Speed filed in USB PortSc register

  @return The USB Port Speed.

**/
UINT16
XhcCheckUsbPortSpeedUsedPsic (
  IN USB_XHCI_INSTANCE  *Xhc,
  IN UINT8              Speed
  );

#endif