esphome-docs/components/sensor/ld2410.rst

186 lines
5.4 KiB
ReStructuredText
Raw Normal View History

LD2410 Sensor
=============
.. seo::
:description: Instructions for setting up LD2410 sensors.
:image: ld2410.jpg
Component/Hub
-------------
.. _ld2410-component:
The ``ld2410`` sensor platform allows you to use HI-LINK LD2410 motion and presence sensor.
(`datasheet and user manual <https://drive.google.com/drive/folders/1p4dhbEJA3YubyIjIIC7wwVsSo8x29Fq-?spm=a2g0o.detail.1000023.17.93465697yFwVxH>`__) with ESPHome.
The :ref:`UART <uart>` is required to be set up in your configuration for this sensor to work.
Use of hardware UART pins is highly recommended, in order to support the out-of-the-box 256000 baud rate of the LD2410 sensor.
.. figure:: images/ld2410.jpg
:align: center
:width: 50.0%
LD2410 motion and presence sensor
.. code-block:: yaml
# Example configuration entry
uart:
tx_pin: REPLACEME
rx_pin: REPLACEME
baud_rate: 256000
parity: NONE
stop_bits: 1
ld2410:
timeout: 150s
max_move_distance : 6m
max_still_distance: 0.75m
g0_move_threshold: 10
g0_still_threshold: 20
g1_move_threshold: 10
g1_still_threshold: 20
g2_move_threshold: 20
g2_still_threshold: 21
g3_move_threshold: 30
g3_still_threshold: 31
g4_move_threshold: 40
g4_still_threshold: 41
g5_move_threshold: 50
g5_still_threshold: 51
g6_move_threshold: 60
g6_still_threshold: 61
g7_move_threshold: 70
g7_still_threshold: 71
g8_move_threshold: 80
g8_still_threshold: 81
.. note::
For UART configuration, ``baud_rate``, ``parity`` and ``stop_bits`` **must be** respectively ``256000``, ``NONE`` and ``1``.
Use of hardware UART pins is highly recommended, in order to support the out-of-the-box 256000 baud rate of the LD2410 sensor.
Configuration variables:
************************
The configuration is made up of three parts: The central component, individual sensors,
and binary sensors.
- **timeout** (*Optional*, int): Time in seconds during which presence state will stay present
after leaving. Defaults to ``5s``.
- **max_move_distance** (*Optional*, int): Maximum distance for movement detection.
Value between ``0.75m`` and ``6m`` inclusive. Defaults to ``4.5m``.
- **max_still_distance** (*Optional*, int): Maximum distance for still detection.
Value between ``0.75m`` and ``6m`` inclusive. Defaults to ``4.5m``.
- **gX_move_threshold** (*Optional*, int): Threshold for the Xth gate for motion detection (X => 0 to 8).
Above this level for the considered gate (distance), movement detection will be triggered. Defaults to ``see table below``.
- **gX_still_threshold** (*Optional*, int): Threshold for the Xth gate for still detection. (X => 0 to 8).
Above this level for the considered gate (distance), still detection will be triggered. Defaults to ``see table below``.
.. list-table:: Default values for gate threshold
:widths: 25 25 25
:header-rows: 1
* - Gate
- Default Move threshold
- Default Still threshold
* - 0
- 50
- 0
* - 1
- 50
- 0
* - 2
- 40
- 40
* - 3
- 40
- 40
* - 4
- 40
- 40
* - 5
- 40
- 40
* - 6
- 30
- 15
* - 7
- 30
- 15
* - 8
- 30
- 15
Sensor
------
The ``ld2410`` sensor allows you to use your :doc:`ld2410` to perform different
measurements.
.. code-block:: yaml
sensor:
- platform: ld2410
moving_distance:
name : Moving Distance
still_distance:
name: Still Distance
moving_energy:
name: Move Energy
still_energy:
name: Still Energy
detection_distance:
name: Detection Distance
Configuration variables:
************************
- **moving_distance** (*Optional*): Distance of detected moving target.
All options from :ref:`Sensor <config-sensor>`.
- **still_distance** (*Optional*): Distance of detected still target.
All options from :ref:`Sensor <config-sensor>`.
- **moving_energy** (*Optional*): Energy for moving target.
All options from :ref:`Sensor <config-sensor>`.
- **still_energy** (*Optional*): Energy for still target.
All options from :ref:`Sensor <config-sensor>`.
- **detection_distance** (*Optional*): Distance in cm of target.
All options from :ref:`Sensor <config-sensor>`.
Binary Sensor
-------------
The ``ld2410`` binary sensor allows you to use your :doc:`ld2410` to perform different
measurements.
.. code-block:: yaml
binary_sensor:
- platform: ld2410
has_target:
name: Presence
has_moving_target:
name: Moving Target
has_still_target:
name: Still Target
Configuration variables:
************************
- **has_target** (*Optional*): If true target detect either still or in movement.
All options from :ref:`Binary Sensor <config-binary_sensor>`.
- **has_moving_target** (*Optional*): If true a moving target is detected.
All options from :ref:`Binary Sensor <config-binary_sensor>`.
- **has_still_target** (*Optional*): If true a still target is detected.
All options from :ref:`Binary Sensor <config-binary_sensor>`.
See Also
--------
- `Official Datasheet and user manuals <https://drive.google.com/drive/folders/1p4dhbEJA3YubyIjIIC7wwVsSo8x29Fq->`_
- `Source of inspiration for implementation <https://github.com/rain931215/ESPHome-LD2410>`_
- :apiref:`ld2410/ld2410.h`
- :ghedit:`Edit`