esphome-docs/devices/sonoff_t1_uk_3gang_v1.1.rst

318 lines
12 KiB
ReStructuredText
Raw Normal View History

Using With Sonoff T1 UK 3 Gang
==============================
.. seo::
:description: Instructions for putting Sonoff T1 UK 3 Gang devices into flash mode and installing ESPHome on them.
:image: sonoff_t1_uk_3g_v1.1.jpg
ESPHome can also be used with Sonoff T1 UK 3 Gang wireless switches. These devices are
basically just an ESP8266 chip with 3 relays to control power output ant three backlit capacitive touch buttons to control the relays.
.. note::
This instruction is made for T1 UK with the touch board v1.1 which is trickier to get into flash mode
than v1
.. figure:: images/sonoff_t1_uk_3g_v1.1.jpg
:align: center
:width: 75.0%
Sonoff T1 UK 3 Gang WiFi switch.
This guide will step you through setting up your Sonoff T1 UK 3 Gang and flashing the first ESPHome firmware
with the serial interface. After that, you will be able to upload all future firmwares with the remote
Over-The-Air update process.
.. note::
If you've previously installed Sonoff-Tasmota on your Sonoff T1 UK 3 Gang, you're in luck 😀
ESPHome can generate a firmware binary which you can then upload via the
Tasmota web interface. To see how to create this binary, skip to :ref:`sonoff_t1_uk_3g_v1.1-creating_firmware`.
Since firmware version 1.6.0, iTead (the creator of this device) has removed the ability to upload
a custom firmware through their own upload process. Unfortunately, that means that the only way to
flash the initial ESPHome firmware is by physically opening the device up and using the UART
interface.
.. warning::
Opening up this device can be very dangerous if not done correctly. While the device is open,
you will be a single touch away from being electrocuted if the device is plugged in.
So, during this *entire* guide **never ever** plug the device in. Also, you should only do this
if you know what you're doing. If you, at any step, feel something is wrong or are uncomfortable
with continuing, it's best to just stop for your own safety.
It's your own responsibility to make sure everything you do during this setup process is safe.
For this guide you will need:
- Sonoff T1 UK 3 Gang 😉
- An USB to UART Bridge for flashing the device. These can be bought on Amazon for less than 5 dollars.
Note that the bridge *must* be 3.3V compatible. Otherwise you will destroy your Sonoff.
- Jumper wires to connect the UART bridge to the header pins and to connect GPIO0 to the Ground.
- Computer running ESPHome or Hass.io add-on.
- Screwdriver to open up the Sonoff T1 UK 3 Gang.
Have everything? Great! Then you can start.
Step 1: Opening up the Sonoff T1 UK 3 Gang
------------------------------------------
The first step is to open up the Sonoff T1 UK 3 Gang. Note that you do not have to run the original firmware
supplied with the Sonoff T1 UK 3 Gang before doing this step.
.. warning::
Just to repeat this: Make **absolutely sure** the device is not connected to any appliance or
plugged in before doing this step.
While the device is not plugged in, turn the device face down and put a narrow flat screwdriver into the slot at the bottom.
With careful twisting motion detatch the face plate.
.. figure:: images/sonoff_t1_uk_3g_back_v1.1.jpg
:align: center
:width: 60.0%
Careful twisting motion.
After that, use the same screwdriver to carefully lift the top PCB off of the switch.
This PCB contains the ESP chip and what's left inside the switch body are relays.
.. figure:: images/sonoff_t1_uk_3g_plate_off_v1.1.jpg
:align: center
:width: 75.0%
"TOUCH BOARD" with touch pads holds the ESP chip.
Step 2: Connecting UART
-----------------------
Now we need our computer to somehow establish a data connection to the board. For this we will
have to connect the four wires on the UART to USB bridge to the UART pins of the Sonoff T1 v1.1.
Fortunately for us, these pins on the ESP controller have dedicated solder pads on the PCB. You can identify
these by the ``VCC33``, ``RX``, ``TX`` and ``GND`` markings on the silk-screen.
Now go ahead and connect these pins to your UART to USB bridge as seen in below image. Make sure
that you connect these correctly, especially the ``VCC33`` and ``GND`` parts as you can otherwise
destroy the chip.
``VCC33`` should be connected to the ``3V3`` (**not** 5V) pin of the UART bridge, ``GND`` to ``GND``
and the same with ``RX``/``TX``.
There's no need for soldering - for quick job like one time firmware flashing you can just hold pins in respective holes by hand
provided **you are not touching any live contacts**, only the wires.
.. note::
On some older T1 UK 3 Gangs, the ``RX`` and ``TX`` pins are swapped (sometimes even the written silkscreen is
2019-10-21 20:35:56 +02:00
wrong). If your upload fails with an ``error: espcomm_upload_mem failed`` message it's most likely due
to the pins being swapped. In that case, just swap ``RX`` and ``TX`` and try again - you won't break
anything if they're swapped.
.. _sonoff_t1_uk_3g_v1.1-creating_firmware:
Step 3: Creating Firmware
-------------------------
The Sonoff T1 UK 3 Gang is based on the ``ESP8266`` platform (technically it's the ``ESP8285``, but for our purposes
they're the same) and is a subtype of the ``esp01_1m`` board.
With this information, you can step through the ESPHome wizard (``esphome sonoff_t1_uk_3g.yaml wizard``),
or alternatively, you can just take the below configuration file and modify it to your needs.
.. code-block:: yaml
esphome:
name: <NAME_OF_NODE>
platform: ESP8266
board: esp01_1m
wifi:
ssid: <YOUR_SSID>
password: <YOUR_PASSWORD>
api:
logger:
ota:
Now run ``esphome sonoff_t1_uk_3g_v1.1.yaml compile`` to validate the configuration and
pre-compile the firmware.
.. note::
After this step, you will be able to find the compiled binary under
``<NAME_OF_NODE>/.pioenvs/<NAME_OF_NODE>/firmware.bin``. If you're having trouble with
uploading, you can also try uploading this file directly with other tools.
Step 4: Uploading Firmware
--------------------------
In order to upload the firmware, you're first going to need to get the chip into a flash mode, otherwise
the device will start up without accepting any firmware flash attempts.
To put ESP8266 into flash mode you need to connect ``GPIO0`` to ``GND`` when the device is powering up.
This is a tricky process with T1 and the best way to do it is to use a wire with pins on either side.
To do this, while the device is UART bridge is not connected to your USB port, flip the PCB over,
take a wire and connect the second Ground hole on the PCB (red) to the third from the right bottom leg on the chip as depicted below (yellow) -
that leg is connected to the GPIO0 on ESP and plug the UART to your USB port.
Keep holding GND and GPIO0 connected for 2-4 seconds. The T1 UK 3 Gang should now be in a flash mode and should not blink with any LED.
The touchpads may light up.
.. figure:: images/sonoff_t1_uk_3g_back_plate_v1.1.jpg
:align: center
Connect red and yellow contacts while powering the board.
Now you can finally run the upload command:
.. code-block:: bash
esphome sonoff_t1_uk_3g_v1.1.yaml run
If successful, you should see something like this:
.. figure:: images/sonoff_4ch_upload.png
:align: center
Hooray 🎉! You've now successfully uploaded the first ESPHome firmware to your Sonoff T1 UK 3 Gang. And in a moment,
you will be able to use all of ESPHome's great features with your Sonoff T1 UK 3 Gang. Now you can put your T1 back together and fire up.
.. note::
While now your T1 will start up and connect to your WiFi network if you power it up from UART it will not behave normally,
it may flash random LEDs, turn on anf off touchpads' backlight and not react on touching touchpads. This will all be fixed once you re-assemble your T1
and power it up from the mains power once safe to do so.
If above step does, however, not work, here are some steps that can help:
- Sometimes the UART bridge cannot supply enough current to the chip to operate, in this
case use a 3.3V supply you have lying around. A nice hack is to use the power supply of
NodeMCU boards. Simply connect the NodeMCU's 3.3V to VCC and GND to GND. **Do not attempt
to plug the device into a socket to overcome this problem while troubleshooting.**
- In other cases the ``TX`` and ``RX`` pin are reversed. Simple disconnect the device, swap
the two pins and put it into flash mode again.
Step 5: Adding the Button, Relay and LEDs
-----------------------------------------
Now we would like the T1 UK 3 Gang to actually do something, not just connect to WiFi and pretty much sit idle.
Below you will find a table of all usable GPIO pins of the Sonoff T1 UK 3 Gang and a configuration file that exposes all
of the basic functions.
======================================== =========================================
``GPIO0`` Touchpad #1 (inverted)
---------------------------------------- -----------------------------------------
``GPIO9`` Touchpad #2 (inverted)
---------------------------------------- -----------------------------------------
``GPIO10`` Touchpad #3 (inverted)
---------------------------------------- -----------------------------------------
``GPIO12`` Relay #1 and Touchpad #1 backlight
---------------------------------------- -----------------------------------------
``GPIO5`` Relay #2 and Touchpad #2 backlight
---------------------------------------- -----------------------------------------
``GPIO4`` Relay #3 and Touchpad #3 backlight
---------------------------------------- -----------------------------------------
``GPIO13`` Blue LED (inverted)
---------------------------------------- -----------------------------------------
``GPIO1`` ``RX`` pin (for external sensors)
---------------------------------------- -----------------------------------------
``GPIO3`` ``TX`` pin (for external sensors)
======================================== =========================================
.. code-block:: yaml
esphome:
name: <NAME_OF_NODE>
platform: ESP8266
board: esp01_1m
wifi:
ssid: <YOUR_SSID>
password: <YOUR_PASSWORD>
api:
logger:
ota:
binary_sensor:
- platform: gpio
pin:
number: GPIO0
mode: INPUT_PULLUP
inverted: True
name: "Sonoff T1 UK 3 Gang Touchpad 1"
- platform: gpio
pin:
number: GPIO9
mode: INPUT_PULLUP
inverted: True
name: "Sonoff T1 UK 3 Gang Touchpad 2"
- platform: gpio
pin:
number: GPIO10
mode: INPUT_PULLUP
inverted: True
name: "Sonoff T1 UK 3 Gang Touchpad 3"
- platform: status
name: "Sonoff T1 UK 3 Gang Status"
switch:
- platform: gpio
name: "Sonoff T1 UK 3 Gang Relay 1"
pin: GPIO12
- platform: gpio
name: "Sonoff T1 UK 3 Gang Relay 2"
pin: GPIO5
- platform: gpio
name: "Sonoff T1 UK 3 Gang Relay 3"
pin: GPIO4
output:
# Register the blue LED as a dimmable output ....
- platform: esp8266_pwm
id: blue_led
pin: GPIO13
inverted: True
light:
# ... and then make a light out of it.
- platform: monochromatic
name: "Sonoff T1 UK 3 Gang Blue LED"
output: blue_led
Above example also showcases an important concept of esphome: IDs and linking. In order
to make all components in esphome as much "plug and play" as possible, you can use IDs to define
them in one area, and simply pass that ID later on. For example, above you can see an PWM (dimmer)
output being created with the ID ``blue_led`` for the blue LED. Later on it is then transformed
into a :doc:`monochromatic light </components/light/monochromatic>`.
If you additionally want the buttons to control the relays, look at `the complete Sonoff T1 UK 3 Gang
with automation example <https://github.com/OttoWinter/esphomedocs/blob/current/devices/sonoff_t1_uk_3gang_v1.1.yaml>`__.
Step 6: Finishing Up
--------------------
If you're sure everything is done with the T1 UK 3 Gang and have double checked there's nothing that could cause a short
in the case, you can put the T1 back together.
Now triple or even quadruple check the UART bridge is not connected to the T1 UK 3 Gang, then comes the time when you can
connect it.
Happy hacking!
See Also
--------
- :doc:`sonoff`
- :doc:`sonoff_4ch`
- :doc:`sonoff_s20`
- :ghedit:`Edit`