esphome-docs/components/mcp230xx.rst

203 lines
5.8 KiB
ReStructuredText
Raw Normal View History

MCP230xx I/O Expander
2019-03-14 16:41:37 +01:00
=====================
.. seo::
:description: Instructions for setting up MCP23008, MCP23016 or MCP23017 digital port expander in ESPHome.
:image: mcp230xx.png
The Microchip MCP230xx series of general purpose, parallel I/O expansion for I²C bus applications.
**Supported Variants :**
2019-03-14 16:41:37 +01:00
- :ref:`mcp23008-label`
- :ref:`mcp23016-label`
- :ref:`mcp23017-label`
2019-03-14 16:41:37 +01:00
.. _mcp23008-label:
MCP23008 Component
------------------
The MCP23008 component (`datasheet <http://ww1.microchip.com/downloads/en/devicedoc/21919e.pdf>`__,
`Adafruit <https://www.adafruit.com/product/593>`__) has 8 GPIOs that can be configured independently.
2019-03-14 16:41:37 +01:00
.. code-block:: yaml
# Example configuration entry
mcp23008:
- id: 'mcp23008_hub'
2019-03-14 16:41:37 +01:00
address: 0x20
# Individual outputs
switch:
- platform: gpio
name: "MCP23008 Pin #0"
2019-03-14 16:41:37 +01:00
pin:
mcp23xxx: mcp23008_hub
2019-03-14 16:41:37 +01:00
# Use pin number 0
number: 0
mode: OUTPUT
inverted: False
# Individual inputs
binary_sensor:
- platform: gpio
name: "MCP23008 Pin #1"
pin:
mcp23xxx: mcp23008_hub
# Use pin number 1
number: 1
# One of INPUT or INPUT_PULLUP
mode: INPUT
2019-03-14 16:41:37 +01:00
inverted: False
Configuration variables:
************************
2019-03-14 16:41:37 +01:00
- **id** (**Required**, :ref:`config-id`): The id to use for this MCP23008 component.
2019-03-14 16:41:37 +01:00
- **address** (*Optional*, int): The I²C address of the driver.
Defaults to ``0x20``.
- **open_drain_interrupt** (*Optional*, bool): Configure the interrupt pin to open-drain mode.
Useful when the MCP23008's power supply is greater than 3.3 volts. Note that this pin
will require a pull-up resistor (to 3.3 volts) when this mode is enabled.
2019-03-14 16:41:37 +01:00
2021-03-09 02:53:04 +01:00
Pin configuration variables:
****************************
- **mcp23xxx** (**Required**, :ref:`config-id`): The id of the MCP23008 component.
- **interrupt** (*Optional*): Set this pin to trigger the INT pin on the component. Can be one of ``CHANGE``, ``RISING``, ``FALLING``.
2021-03-09 02:53:04 +01:00
- **number** (**Required**, integer): The pin number.
- **inverted** (*Optional*, boolean): If all read and written values
should be treated as inverted. Defaults to ``False``.
- **mode** (*Optional*, string): A pin mode to set for the pin at. One of ``INPUT`` or ``OUTPUT``.
.. _mcp23016-label:
MCP23016 Component
------------------
The MCP23016 component (`datasheet <http://ww1.microchip.com/downloads/en/devicedoc/20090c.pdf>`__)
has 16 GPIOs and can be configured the same way than the other variants.
.. note::
The 'INPUT_PULLUP' mode is not supported on this device.
.. code-block:: yaml
# Example configuration entry
mcp23016:
- id: 'mcp23016_hub'
address: 0x20
# Individual outputs
switch:
- platform: gpio
name: "MCP23016 Pin #0"
pin:
mcp23016: mcp23016_hub
# Use pin number 0
number: 0
mode: OUTPUT
inverted: False
# Individual inputs
binary_sensor:
- platform: gpio
name: "MCP23016 Pin #1"
pin:
mcp23016: mcp23016_hub
# Use pin number 1
number: 1
mode: INPUT
inverted: False
Configuration variables:
************************
- **id** (**Required**, :ref:`config-id`): The id to use for this MCP23016 component.
- **address** (*Optional*, int): The I²C address of the driver.
Defaults to ``0x20``.
2021-03-09 02:53:04 +01:00
Pin configuration variables:
****************************
2021-03-09 02:53:04 +01:00
- **mcp23xxx** (**Required**, :ref:`config-id`): The id of the MCP23016 component.
- All other options from :ref:`Pin Schema <config-pin_schema>`
.. _mcp23017-label:
MCP23017 Component
------------------
The MCP23017 component allows you to use MCP23017 I/O expanders
(`datasheet <http://ww1.microchip.com/downloads/en/devicedoc/20001952c.pdf>`__,
`Adafruit <https://www.adafruit.com/product/732>`__) in ESPHome.
It uses the :ref:`I²C Bus <i2c>` for communication.
Once configured, you can use any of the 16 pins as
pins for your projects. Within ESPHome they emulate a real internal GPIO pin
and can therefore be used with many of ESPHome's components such as the GPIO
binary sensor or GPIO switch.
.. code-block:: yaml
# Example configuration entry
mcp23017:
- id: 'mcp23017_hub'
address: 0x20
# Individual outputs
switch:
- platform: gpio
name: "MCP23017 Pin #0"
pin:
mcp23xxx: mcp23017_hub
# Use pin number 0
number: 0
mode: OUTPUT
inverted: False
# Individual inputs
binary_sensor:
- platform: gpio
name: "MCP23017 Pin #1"
pin:
mcp23xxx: mcp23017_hub
# Use pin number 1
number: 1
# One of INPUT or INPUT_PULLUP
mode: INPUT_PULLUP
inverted: False
Configuration variables:
************************
- **id** (**Required**, :ref:`config-id`): The id to use for this MCP23017 component.
- **address** (*Optional*, int): The I²C address of the driver.
Defaults to ``0x20``.
- **open_drain_interrupt** (*Optional*, bool): Configure interrupt pins to open-drain mode.
Useful when the MCP23017's power supply is greater than 3.3 volts. Note that these pins
will require pull-up resistors (to 3.3 volts) when this mode is enabled.
2021-03-09 02:53:04 +01:00
Pin configuration variables:
****************************
- **mcp23xxx** (**Required**, :ref:`config-id`): The id of the MCP23017 component.
- **interrupt** (*Optional*): Set this pin to trigger the port INT pin on the component. Can be one of ``CHANGE``, ``RISING``, ``FALLING``.
- All other options from :ref:`Pin Schema <config-pin_schema>`
2019-03-14 16:41:37 +01:00
See Also
--------
- :ref:`i2c`
- :doc:`switch/gpio`
- :doc:`binary_sensor/gpio`
- :apiref:`API Reference (MCP23008) <mcp23008/mcp23008.h>`
- :apiref:`API Reference (MCP23016) <mcp23016/mcp23016.h>`
- :apiref:`API Reference (MCP23017) <mcp23017/mcp23017.h>`
2019-03-14 16:41:37 +01:00
- :ghedit:`Edit`