esphome-docs/cookbook/esw01-eu.rst

125 lines
3.4 KiB
ReStructuredText
Raw Normal View History

Etekcity Voltson (ESW01-EU)
===========================
.. seo::
:description: Configure an Etekcity Voltson and calculate the missing current sensor
:image: esw01-eu.jpg
:keywords: Etekcity, Voltson, ESW01, ESW01-EU, HLW8012, Home Assistant, ESPHome
The Etekcity Voltson brings a 10A relay, two LEDs (blue and yellow), a push button and a :doc:`/components/sensor/hlw8012`
in a very small package and at a reasonable price.
.. note::
There are quite a few hardware revisions out there. Also reginal versions like US, UK and EU are different.
Flashing
--------
Opening the case for flashing varies a lot for different hardware revisions. Mine was easy as it had two tiny T5 Torx screws in the front and four Philipps screws inside.
Once you have opened the case, remove the PCB from it and attach your TTL as follows:
5V and GND go to the bottom:
.. figure:: images/esw01-eu-pcb-bottom.jpg
:align: center
:width: 75.0%
On the opposite side, T12 is TX, T13 is RX. During boot you need to connect T11 and T16 pads to GND. Easiest is to flash with pogo pins.
.. figure:: images/esw01-eu-pcb-top.jpg
:align: center
:width: 75.0%
Configuration
-------------
As the Voltson has its SEL pin permanently pulled high, we are unable to switch from voltage measurement to current measurement.
This will be circumvented by defining the initial mode to be voltage measurement (see :doc:`/components/sensor/hlw8012` documentation)
and calculating the current with `Ohm's law <https://en.wikipedia.org/wiki/Ohm%27s_law>`_: ``P (watts) = V (volts) x I (amps)``
.. code-block:: yaml
esphome:
name: voltson
2022-02-10 23:10:43 +01:00
esp8266:
board: esp01_1m
### you wifi and other settings here ###
### pins ###
# D1 GPIO5 | LED blue | status_led
# D0 GPIO16 | LED yellow | led1
# D5 GPIO14 | SW1 | button1
# D2 GPIO4 | REL1 | relay1
# D6 GPIO12 | HLW8012/CF1 | cf1_pin
# D7 GPIO13 | HLW8012/CF | cf_pin
status_led:
pin:
number: GPIO5
output:
- platform: gpio
id: relay1
pin: GPIO4
- platform: gpio
id: led1
pin: GPIO16
switch:
- platform: output
name: "Voltson Relay"
id: switch1
output: relay1
on_turn_on:
- output.turn_on: led1
on_turn_off:
- output.turn_off: led1
binary_sensor:
- platform: gpio
id: button1
pin:
number: GPIO14
mode:
input: true
pullup: true
inverted: true
on_press:
- switch.toggle: switch1
sensor:
- platform: hlw8012
sel_pin: 0 # not connected
cf_pin: GPIO13
cf1_pin: GPIO12
voltage:
id: hlw8012_voltage
name: "HLW8012 Voltage"
power:
id: hlw8012_power
name: "HLW8012 Power"
on_value:
- sensor.template.publish:
id: hlw8012_current_calculated
state: !lambda 'return id(hlw8012_power).state / id(hlw8012_voltage).state;'
update_interval: 10s
initial_mode: VOLTAGE
change_mode_every: 4294967295 # basically never
- platform: template
id: hlw8012_current_calculated
name: "HLW8012 Current (calculated)"
unit_of_measurement: A
accuracy_decimals: 2
See Also
--------
- :doc:`/components/sensor/hlw8012`
- :ghedit:`Edit`