esphome-docs/components/dfplayer.rst

430 lines
9.4 KiB
ReStructuredText
Raw Normal View History

DF-Player mini
==============
.. seo::
:description: Instructions for setting up DF Player Mini integration in ESPHome.
:image: crosshair-gps.png
The ``dfplayer`` (`datasheet <https://wiki.dfrobot.com/DFPlayer_Mini_SKU_DFR0299>`__), component
2019-11-22 14:45:16 +01:00
allows you to play sound and music stored in an SD card or USB flash drive.
.. figure:: images/dfplayer-full.jpg
:align: center
:width: 50.0%
DF-Player mini Module.
For this integration to work you need to have set up a :ref:`UART bus <uart>`
in your configuration.
Overview
--------
2021-01-11 17:46:37 +01:00
The module can be powered by the 3.3V output of a NodeMCU. For communication you can connect only
the ``tx_pin`` of the ``uart`` bus to the module's ``RX`` but if you need feedback of playback active
2019-11-22 14:45:16 +01:00
you will also need to connect the ``rx_pin`` to the module's ``TX``.
For best quality audio a powered stereo speaker can be connected to the modules ``DAC_R``,
``DAC_L`` and ``GND``, alternatively the module features a built-in 3W audio amplifier, in that case
2019-11-22 14:45:16 +01:00
the pins ``SPK_1`` and ``SPK_2`` should be connected to one passive speaker and a 5V 1A power supply
will be required.
.. code-block:: yaml
# Example configuration entry
uart:
tx_pin: GPIO2
rx_pin: GPIO5
baud_rate: 9600
# Declare DFPlayer mini module
dfplayer:
on_finished_playback:
then:
logger.log: 'Somebody press play!'
Configuration variables:
------------------------
- **uart_id** (*Optional*, :ref:`config-id`): Manually specify the ID of the UART hub.
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID used for code generation.
- **on_finished_playback** (*Optional*, :ref:`Automation <automation>`): An action to be
performed when playback is finished.
``dfplayer.is_playing`` Condition
---------------------------------
This Condition returns true while playback is active.
.. code-block:: yaml
# In some trigger:
on_...:
if:
condition:
dfplayer.is_playing
then:
logger.log: 'Playback is active!'
``dfplayer.play_next`` Action
-----------------------------
Starts playback of next track or skips to the next track.
.. code-block:: yaml
on_...:
then:
- dfplayer.play_next:
``dfplayer.play_previous`` Action
---------------------------------
Plays the previously played track.
.. code-block:: yaml
on_...:
then:
- dfplayer.play_previous:
``dfplayer.play`` Action
------------------------
Plays a track.
.. code-block:: yaml
on_...:
then:
- dfplayer.play:
file: 23
loop: false
# Shorthand
- dfplayer.play: 23
Configuration options:
- **file** (*Optional*, int, :ref:`templatable <config-templatable>`): The global track
number (from all tracks in the device). If not specified plays the first track.
- **loop** (*Optional*, boolean, :ref:`templatable <config-templatable>`): Repeats playing
the same track. Defaults to ``false``.
``dfplayer.play_folder`` Action
-------------------------------
Plays files inside numbered folders, folders must be numbered from 1 and with leading
zeros. Like ``01``, ``02``, ... etc. Files inside the folders must be numbered with two
leading zeros, like ``001.mp3``, ``002.mp3``, ... etc.
Folder numbers can range from 1 to 99 and file name from 1 to 255 or folder number
from 1 to 10 and file number from 1 to 1000.
.. code-block:: bash
/01
/001.mp3
/002.mp3
..
/02
/001.mp3
/002.mp3
/003.mp3
..
.. code-block:: yaml
on_...:
then:
- dfplayer.play_folder:
2019-10-19 23:12:46 +02:00
folder: 2
file: 1
Configuration options:
- **folder** (**Required**, int, :ref:`templatable <config-templatable>`): The folder number.
- **file** (*Optional*, int, :ref:`templatable <config-templatable>`): The file number
inside the folder to play. Optional only if ``loop`` is not set.
- **loop** (*Optional*, boolean, :ref:`templatable <config-templatable>`): Repeats playing
all files in the folder. Causes ``file`` to be ignored. Defaults to ``false``.
``dfplayer.set_device`` Action
------------------------------
2019-11-22 14:45:16 +01:00
Changes the device in use. Valid values are ``TF_CARD`` and ``USB``.
.. code-block:: yaml
on_...:
then:
- dfplayer.set_device: TF_CARD
``dfplayer.set_volume`` Action
------------------------------
Changes volume.
.. code-block:: yaml
on_...:
then:
- dfplayer.set_volume:
volume: 20
# Shorthand
- dfplayer.set_volume: 20
Configuration options:
- **volume** (**Required**, int, :ref:`templatable <config-templatable>`): The volume value.
Valid values goes from ``0`` to ``30``.
``dfplayer.volume_up`` Action
-----------------------------
Turn volume up.
.. code-block:: yaml
on_...:
then:
- dfplayer.volume_up
``dfplayer.volume_down`` Action
-------------------------------
Turn volume down.
.. code-block:: yaml
on_...:
then:
- dfplayer.volume_down
``dfplayer.set_eq`` Action
--------------------------
Changes audio equalization preset.
.. code-block:: yaml
on_...:
then:
- dfplayer.set_eq:
eq_preset: ROCK
# Shorthand
- dfplayer.set_eq: ROCK
Configuration options:
- **eq_preset** (**Required**): Eq Preset value. Valid values are ``NORMAL``, ``POP``, ``ROCK``, ``JAZZ``,
``CLASSIC`` and ``BASS``.
``dfplayer.sleep`` Action
-------------------------
Enters sleep mode. Playback is stopped and the action ``dfplayer.set_device: TF_CARD`` should be
send for playback to be enabled again.
.. code-block:: yaml
on_...:
then:
- dfplayer.sleep
``dfplayer.reset`` Action
-------------------------
Module reset.
.. code-block:: yaml
on_...:
then:
- dfplayer.reset
``dfplayer.start`` Action
-------------------------
Starts playing a track or resumes paused playback.
.. code-block:: yaml
on_...:
then:
- dfplayer.start
``dfplayer.pause`` Action
-------------------------
Pauses playback, playback can be resumed from the same position with ``dfplayer.start``.
.. code-block:: yaml
on_...:
then:
- dfplayer.pause
``dfplayer.stop`` Action
------------------------
Stops playback.
.. code-block:: yaml
on_...:
then:
- dfplayer.stop
``dfplayer.random`` Action
--------------------------
Randomly plays all tracks.
.. code-block:: yaml
on_...:
then:
- dfplayer.random
All actions
-----------
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID of the DFPlayer if you have multiple components.
Test setup
----------
With the following code you can quickly setup a node and use Home Assistant's service in the developer tools.
E.g. for calling ``dfplayer.play_folder`` select the service ``esphome.test_node_dfplayer_play`` and in
service data enter
.. code-block:: json
{ "file": 23 }
Sample code
***********
.. code-block:: yaml
esphome:
name: test_node
platform: ESP8266
board: nodemcu
wifi:
ssid: !secret wifi_ssid
password: !secret wifi_pass
logger:
level: VERBOSE
uart:
tx_pin: GPIO2
rx_pin: GPIO5
baud_rate: 9600
dfplayer:
on_finished_playback:
then:
logger.log: 'Playback finished event'
api:
services:
- service: dfplayer_next
then:
- dfplayer.play_next:
- service: dfplayer_previous
then:
- dfplayer.play_previous:
- service: dfplayer_play
variables:
file: int
then:
- dfplayer.play: !lambda 'return file;'
- service: dfplayer_play_loop
variables:
file: int
loop_: bool
then:
- dfplayer.play:
file: !lambda 'return file;'
loop: !lambda 'return loop_;'
- service: dfplayer_play_folder
variables:
folder: int
file: int
then:
- dfplayer.play_folder:
folder: !lambda 'return folder;'
file: !lambda 'return file;'
2019-11-22 14:45:16 +01:00
- service: dfplayer_play_loop_folder
variables:
folder: int
then:
- dfplayer.play_folder:
folder: !lambda 'return folder;'
loop: true
2019-11-22 14:45:16 +01:00
- service: dfplayer_set_device_tf
then:
- dfplayer.set_device: TF_CARD
- service: dfplayer_set_device_usb
then:
2019-11-22 14:45:16 +01:00
- dfplayer.set_device: USB
- service: dfplayer_set_volume
variables:
volume: int
then:
- dfplayer.set_volume: !lambda 'return volume;'
- service: dfplayer_set_eq
variables:
preset: int
then:
- dfplayer.set_eq: !lambda 'return static_cast<dfplayer::EqPreset>(preset);'
- service: dfplayer_sleep
then:
- dfplayer.sleep
- service: dfplayer_reset
then:
- dfplayer.reset
- service: dfplayer_start
then:
- dfplayer.start
- service: dfplayer_pause
then:
- dfplayer.pause
- service: dfplayer_stop
then:
- dfplayer.stop
- service: dfplayer_random
then:
- dfplayer.random
- service: dfplayer_volume_up
then:
- dfplayer.volume_up
- service: dfplayer_volume_down
then:
- dfplayer.volume_down
See Also
--------
- :apiref:`dfplayer/dfplayer.h`
- :ghedit:`Edit`