esphome-docs/components/stepper/index.rst

Stepper Component
=================

.. seo::
    :description: Instructions for setting up stepper motor drivers in ESPHome
    :image: folder-open.png
    :keywords: stepper motor, stepper driver, a4988

The ``stepper`` component allows you to use stepper motors with ESPHome.
Currently only the A4988 stepper driver
(`datasheet <https://www.pololu.com/file/0J450/a4988_DMOS_microstepping_driver_with_translator.pdf>`__)
and ULN2003 (`datasheet <http://www.ti.com/lit/ds/symlink/uln2003a.pdf>`__) are supported.

.. note::

    This component will not show up in the Home Assistant front-end automatically because
    Home Assistant doesn't have support for steppers. Please see :ref:`stepper-ha-config`.

A4988 Configuration
-------------------

.. code-block:: yaml

    # Example configuration entry
    stepper:
      - platform: a4988
        id: my_stepper
        step_pin: D0
        dir_pin: D1
        max_speed: 250 steps/s

        # Optional:
        sleep_pin: D2
        acceleration: inf
        deceleration: inf


Configuration variables:

- **id** (**Required**, :ref:`config-id`): Specify the ID of the stepper so that you can control it.
- **step_pin** (**Required**, :ref:`Pin Schema <config-pin_schema>`): The ``STEP`` pin of the A4988
  stepper driver.
- **dir_pin** (**Required**, :ref:`Pin Schema <config-pin_schema>`): The ``DIRECTION`` pin of the A4988
  stepper driver.
- **max_speed** (**Required**, float): The maximum speed in ``steps/s`` (steps per seconds) to drive the
  stepper at. Note most steppers can't step properly with speeds higher than 250 steps/s.
- **sleep_pin** (*Optional*, :ref:`Pin Schema <config-pin_schema>`): Optionally also use the ``SLEEP`` pin
  of the A4988 stepper driver. If specified, the driver will be put into sleep mode as soon as the stepper
  reaches the target steps.
- **acceleration** (*Optional*, float): The acceleration in ``steps/s^2`` (steps per seconds squared)
  to use when starting to move. The default is ``inf`` which means infinite acceleration, so the
  stepper will try to drive with the full speed immediately.
- **deceleration** (*Optional*, float): The same as ``acceleration``, but for when the motor is decelerating
  shortly before reaching the set position. Defaults to ``inf`` (immediate deceleration).

.. note::

    If the stepper is driving in the wrong direction, you can invert the ``dir_pin``:

    .. code-block:: yaml

        stepper:
          - platform: a4988
            # ...
            dir_pin:
              number: D1
              inverted: True

ULN2003 Configuration
---------------------

.. code-block:: yaml

    # Example configuration entry
    stepper:
      - platform: uln2003
        id: my_stepper
        pin_a: D0
        pin_b: D1
        pin_c: D2
        pin_d: D3
        max_speed: 250 steps/s

        # Optional:
        acceleration: inf
        deceleration: inf


Configuration variables:

- **id** (**Required**, :ref:`config-id`): Specify the ID of the stepper so that you can control it.
- **pin_a**, **pin_b**, **pin_c**, **pin_d** (**Required**, :ref:`Pin Schema <config-pin_schema>`):
  The four pins of the stepper control board.
- **sleep_when_done** (*Optional*, boolean): Whether to turn off all coils when the stepper has
  reached the target position
- **step_mode** (*Optional*, string): The step mode to operate the motor with. One of:

    - ``FULL_STEP`` (Default)
    - ``HALF_STEP``
    - ``WAVE_DRIVE``

- **max_speed** (**Required**, float): The maximum speed in ``steps/s`` (steps per seconds) to drive the
  stepper at. Note most steppers can't step properly with speeds higher than 250 steps/s.
- **acceleration** (*Optional*, float): The acceleration in ``steps/s^2`` (steps per seconds squared)
  to use when starting to move. The default is ``inf`` which means infinite acceleration, so the
  stepper will try to drive with the full speed immediately.
- **deceleration** (*Optional*, float): The same as ``acceleration``, but for when the motor is decelerating
  shortly before reaching the set position. Defaults to ``inf`` (immediate deceleration).

.. _stepper-set_target_action:

``stepper.set_target`` Action
-----------------------------

To use your stepper motor in :ref:`automations <automation>` or templates, you can use this action to set the target
position (in steps). The stepper will always run towards the target position and stop once it has reached the target.

.. code-block:: yaml

    on_...:
      then:
      - stepper.set_target:
          id: my_stepper
          target: 250

      # Templated
      - stepper.set_target:
          id: my_stepper
          target: !lambda |-
            if (id(my_binary_sensor).state) {
              return 1000;
            } else {
              return -1000;
            }

Configuration options:

- **id** (**Required**, :ref:`config-id`): The ID of the stepper.
- **target** (*Optional*, int, :ref:`templatable <config-templatable>`): The target position in steps.

.. warning::

    This turns the stepper to an absolute position! To have the servo move *relative* to the current
    position, first reset the current position and then set the target to the relative value.

    .. code-block:: yaml

        on_...:
          then:
            # Move 150 steps forward
            - stepper.report_position:
                id: my_stepper
                position: 0
            - stepper.set_target:
                id: my_stepper
                target: 150

.. _stepper-report_position_action:

``stepper.report_position`` Action
----------------------------------

All steppers start out with a target and current position of ``0`` on boot. However, if you for example want to home
a stepper motor, it can be useful to **report** the stepper where it is currently at.

With this action, you can set the stepper's internal position counter to a specific value (in steps). Please note
that reporting the position can create unexpected moves of the stepper. For example, if the stepper's target and
current position is at 1000 steps and you "report" a position of 0, the stepper will move 1000 steps forward to match
the target again.

.. code-block:: yaml

    on_...:
      then:
      - stepper.report_position:
          id: my_stepper
          position: 250
      # It's best to call set_target directly after report_position, so that the stepper doesn't move
      - stepper.set_target:
          id: my_stepper
          target: 250

      # Templated
      - stepper.report_position:
          id: my_stepper
          position: !lambda |-
            if (id(my_binary_sensor).state) {
              return 0;
            } else {
              return -1000;
            }

Configuration options:

- **id** (**Required**, :ref:`config-id`): The ID of the stepper.
- **target** (*Optional*, int, :ref:`templatable <config-templatable>`): The target position in steps.

.. _stepper-set_speed_action:

``stepper.set_speed`` Action
----------------------------

This :ref:`Action <config-action>` allows you to set the speed of a stepper at runtime.

.. code-block:: yaml

    on_...:
      - stepper.set_speed:
          id: my_stepper
          speed: 250 steps/s

Configuration variables:

- **id** (**Required**, :ref:`config-id`): The ID of the stepper.
- **speed** (**Required**, :ref:`templatable <config-templatable>`, float): The speed
  in ``steps/s`` (steps per seconds) to drive the stepper at.

.. _stepper-ha-config:

Home Assistant Configuration
----------------------------

This component will not show up in the Home Assistant frontend automatically because Home Assistant
does not support steppers natively (raise this issue in Home Assistant forums to make this a
higher priority for Home Assistant). You can add this to your Home Assistant configuration to
be able to control the stepper from the frontend.

.. code-block:: yaml

    # Home Assistant configuration
    input_number:
      stepper_control:
        name: Stepper Control
        initial: 0
        min: -1000
        max: 1000
        step: 1
        mode: slider

    automation:
      - alias: Write Stepper Value to ESP
        trigger:
          platform: state
          entity_id: input_number.stepper_control
        action:
          # Replace livingroom with the name you gave the ESP
          - service: esphome.livingroom_control_stepper
            data_template:
              target: '{{ trigger.to_state.state | int }}'

.. code-block:: yaml

    # ESPHome configuration
    api:
      services:
        - service: control_stepper
          variables:
            target: int
          then:
            - stepper.set_target:
                id: my_stepper
                target: !lambda 'return target;'

    stepper:
      - platform: ...
        # [...] stepper config
        id: my_stepper

.. _stepper-lambda_calls:

lambda calls
------------

From :ref:`lambdas <config-lambda>`, you can call several methods on stepper motors to do some
advanced stuff (see the full API Reference for more info).

- ``set_target``: Set the target position of the motor as an integer.

    .. code-block:: cpp

        // Argument is integer (signed int)
        // Set the (absolute) target position to 250 steps
        id(my_stepper).set_target(250);

- ``report_position``: Report the current position as an integer.

    .. code-block:: cpp

        // Report the (absolute) current position as 250 steps
        id(my_stepper).report_position(250);

- ``current_position``: Get the current position of the stepper as an integer.

    .. code-block:: cpp

        int pos = id(my_stepper).current_position;


- ``target_position``: Get the set target position of the stepper  as an integer.

    .. code-block:: cpp

        int pos = id(my_stepper).target_position;

See Also
--------

- :apiref:`stepper/stepper.h`
- :ghedit:`Edit`