H801 LED controller (remade) (#158)

* misc cleanup and fixes

* resize and compression

* added h801 guide

* Resize and compress

* Update h801.rst

* edited in different editor

cookbook/h801.rst

@@ -0,0 +1,100 @@
+H801 RGBW LED controller
+========================
+
+The H801 is pretty afordable and easy to hack and adapt to your needs. It can be found on `Aliexpress <https://s.click.aliexpress.com/e/bbnUDBZW>`__
+`Here <http://tinkerman.cat/closer-look-h801-led-wifi-controller/>`__ is an article about the hardware for those who have an interest for more details about the board.
+It can be used as a RGB, RGBW, RGB dual white or even control 5 individual monochromatic strips if you want or combinations of these.
+
+.. figure:: images/h801.jpg
+    :align: center
+    :width: 80.0%
+
+For esphomelib, you can then use the :doc:`RGBW </components/light/rgbw>` 
+and the :doc:`ESP8266 Software PWM output </components/output/esp8266_pwm>` components using below configuration:
+
+.. code-block:: yaml
+
+    esphomeyaml:
+      name: h801light
+      platform: ESP8266
+      board: esp01_1m
+    wifi:
+      ssid: 'WIFI'
+      password: 'WIFIPASS'
+      manual_ip: 
+        static_ip: x.x.x.x
+        gateway: x.x.x.x
+        subnet: 255.255.255.0
+    logger:
+    api:
+    ota:
+    sensor:
+      - platform: wifi_signal
+        name: "WiFi Signal h801light"
+        update_interval: 60s
+    #RGBWarm
+    output:
+      - platform: esp8266_pwm
+        pin: 12
+        frequency: 1000 Hz
+        id: pwm_b  
+      - platform: esp8266_pwm
+        pin: 15
+        frequency: 1000 Hz
+        id: pwm_g      
+      - platform: esp8266_pwm
+        pin: 13
+        frequency: 1000 Hz
+        id: pwm_r 
+      - platform: esp8266_pwm
+        pin: 14
+        frequency: 1000 Hz
+        id: pwm_w
+    light:
+      - platform: rgbw
+        name: "H801 Light"
+        red: pwm_r
+        green: pwm_g
+        blue: pwm_b
+        white: pwm_w
+
+
+Make your node in the esphome dashboard and compile/upload it. (if it fails OTA it must be uploaded manually with your favorite ESP flasher, e.g. :ref:`esphomeflasher <esphomeflasher>`)
+
+.. figure:: images/gpio.jpg
+    :align: center
+    :width: 80.0%
+
+Front side of board with pins soldered on
+
+.. figure:: images/back.jpg
+    :align: center
+    :width: 80.0%
+
+Back side of the board (don't melt the blue and red wire when soldering)
+
+.. figure:: images/rgbwarm.jpg
+    :align: center
+    :width: 80.0%
+
+This LED strip can be used with the sketch as-is
+
+.. figure:: images/rgbw.jpg
+    :align: center
+    :width: 80.0%
+
+For this type of led strip you have to swap the white and blue gpio numbers in the sketch
+
+You will need to solder pins to the board inside the h801 (fortunately its pretty roomy and not a lot of components or stuff in the way part from the 2 wires on the back)
+
+3.3v, GND, TX and RX (RX to RX and TX to TX) needs to be connected to your serial adapter, the two other pins must be shorted by a jumper or a breadboard cable when flashing. 
+(Remember to remove it after flashing) 
+
+See Also
+--------
+
+- :doc:`/components/light/rgbw`
+- :doc:`/components/output/esp8266_pwm`
+- :ghedit:`Edit`
+
+.. disqus::

index.rst

@@ -296,6 +296,7 @@ This list contains items that are technically already supported by other compone
     Dual Relay Motor Cover, cookbook/dual-r2-cover, sonoff_dual_r2.jpg
     BME280 Environment, cookbook/bme280_environment, bme280.jpg
     Sonoff Fishpond Pump, cookbook/sonoff-fishpond-pump, cookbook-sonoff-fishpond-pump.jpg
+    H801 LED Controller, cookbook/h801, h801.jpg
 
 Do you have other awesome automations or cool setups? Please feel free to add them to the
 documentation for others to copy. See :doc:`Contributing </guides/contributing>`.