Merge branch 'current' into next

cookbook/display_time_temp_oled.rst

@@ -0,0 +1,143 @@
+Time & Temperature on OLED Display
+==================================
+
+.. seo::
+    :description: Instructions for setting up a display in ESPhome to show sensor values from Home Assistant
+    :image: display_time_temp_oled_1.jpg
+    :keywords: Display
+
+.. figure:: images/display_time_temp_oled_1.jpg
+    :align: left
+    :width: 75.0%
+
+In this example I have used a :doc:`SSD1306 OLED Display over I²C </components/display/ssd1306_i2c>` to show current time and two different temperature values from Home Assistant.
+
+ESPHome has support for several different types of displays. The display used here is 1.3" with 128x64 monochrome pixels (``SH1106 128x64``).
+
+Hardware configuration
+----------------------
+
+Hardware is easy! Only four connections are needed:
+
+- ``VCC`` - Power (my display could use either 3.3V or 5V)
+- ``GND`` - Ground
+- ``SDA`` - Serial Data
+- ``SCL`` - Serial Clock
+
+.. warning::
+
+    Ensure your display handles 5V if you use that.
+
+Software configuration
+----------------------
+
+Getting Time
+************
+
+Get the time from Home Assistant to sync the onboard real-time-clock.
+
+.. code-block:: yaml
+
+    time:
+      - platform: homeassistant
+        id: time
+
+Getting Temperature
+*******************
+
+Next, we want to get two temperature sensors imported from Home Assistant. 
+
+I named them ``inside_temperature`` and ``outside_temperature``. You will use those references later.
+
+By adding ``internal: true`` to the sensors they won't be published back to Home Assistant.
+
+.. code-block:: yaml
+
+    sensor:
+      - platform: homeassistant
+        id: inside_temperature
+        entity_id: sensor.mellanvaning_temperature 
+        internal: true
+
+      - platform: homeassistant
+        id: outside_temperature
+        entity_id: sensor.10_00080192969d_temperature
+        internal: true
+
+Define the Fonts
+****************
+
+- TrueType fonts are used. If you ever worked with fonts on microcontrollers you will love this!
+- Save font files in ``/config/esphome`` folder where your esphome configuration is stored. 
+- The ``.ttf`` suffix must be lowercase and of course match your filename. 
+- Selection of fonts can be a little bit tricky for small sizes to look good. Experiment and share your findings in the comments below!
+
+.. code-block:: yaml
+
+    font:
+      - file: 'slkscr.ttf'
+        id: font1
+        size: 8
+
+      - file: 'BebasNeue-Regular.ttf'
+        id: font2
+        size: 48
+
+      - file: 'arial.ttf'
+        id: font3
+        size: 14
+
+Display Definition
+******************
+
+Now setup the communication to the display and start fill the screen with live data! 
+
+The ``reset_pin`` was not used in my hardware configuration as the display didn't had that pin exposed.
+
+Note your ``address`` and ``model`` might be different, use the scan option to find the address of your display.
+
+.. code-block:: yaml
+
+    i2c:
+      sda: D1
+      scl: D2
+      scan: False
+
+    display:
+      - platform: ssd1306_i2c
+        model: "SH1106 128x64"
+        reset_pin: D0
+        address: 0x3C
+        lambda: |-
+          // Print "Mitt Smarta Hus" in top center.
+          it.printf(64, 0, id(font1), TextAlign::TOP_CENTER, "Mitt Smarta Hus");
+
+          // Print time in HH:MM format
+          it.strftime(0, 60, id(font2), TextAlign::BASELINE_LEFT, "%H:%M", id(time).now()); 
+
+          // Print inside temperature (from homeassistant sensor)
+          if (id(inside_temperature).has_state()) { 
+            it.printf(127, 23, id(font3), TextAlign::TOP_RIGHT , "%.1f°", id(inside_temperature).state);
+          } 
+
+          // Print outside temperature (from homeassistant sensor)
+          if (id(outside_temperature).has_state()) { 
+            it.printf(127, 60, id(font3), TextAlign::BASELINE_RIGHT , "%.1f°", id(outside_temperature).state); 
+          }
+
+Rendering
+---------
+
+- Alignment of text can use different reference points, for example ``TOP_RIGHT`` or ``BASELINE_LEFT``, which all are defined in :apiref:`display/display.h`.
+- The property ``has_state()`` on a sensor is useful as it can take some seconds to get the data from Home Assistant and you may not want to display ``Nan``
+- Refer to the rendering engine :ref:`display-engine` for more features (it can draw lines and circles too!)
+
+See Also
+--------
+
+- :doc:`/components/display/ssd1306_i2c`
+- :doc:`/components/display/index`
+- :doc:`/components/sensor/homeassistant`
+- :ghedit:`Edit`
+
+.. disqus::

index.rst

@@ -296,6 +296,7 @@ Cookbook
     BME280 Environment, cookbook/bme280_environment, bme280.jpg
     Sonoff Fishpond Pump, cookbook/sonoff-fishpond-pump, cookbook-sonoff-fishpond-pump.jpg
     H801 LED Controller, cookbook/h801, h801.jpg
+    Time & Temperature on OLED Display, cookbook/display_time_temp_oled, display_time_temp_oled_2.jpg
 
 Do you have other awesome automations or cool setups? Please feel free to add them to the
 documentation for others to copy. See :doc:`Contributing </guides/contributing>`.