diff --git a/components/sensor/ina226.rst b/components/sensor/ina226.rst
index 20139f41f..abe591eb9 100644
--- a/components/sensor/ina226.rst
+++ b/components/sensor/ina226.rst
@@ -7,10 +7,8 @@ INA226 DC current and power sensor
     :keywords: ina226
 
 The ``ina226`` sensor platform allows you to use your INA226 DC Current and Power Sensor
-(`datasheet <http://www.ti.com/lit/ds/symlink/ina226.pdf>`__,
-`eBay`_) sensors with
-ESPHome. The :ref:`I²C Bus <i2c>` is
-required to be set up in your configuration for this sensor to work.
+(`datasheet <http://www.ti.com/lit/ds/symlink/ina226.pdf>`__, `eBay`_) sensors with ESPHome. 
+The :ref:`I²C Bus <i2c>` is required to be set up in your configuration for this sensor to work.
 
 
 .. figure:: images/ina226-full.jpg
@@ -28,6 +26,8 @@ required to be set up in your configuration for this sensor to work.
       - platform: ina226
         address: 0x40
         shunt_resistance: 0.1 ohm
+        max_current: 3.2A
+        update_interval: 60s
         current:
           name: "INA226 Current"
         power:
@@ -36,28 +36,35 @@ required to be set up in your configuration for this sensor to work.
           name: "INA226 Bus Voltage"
         shunt_voltage:
           name: "INA226 Shunt Voltage"
-        max_current: 3.2A
-        update_interval: 60s
 
 Configuration variables:
 ------------------------
 
-- **address** (*Optional*, int): Manually specify the I²C address of the sensor. Defaults to ``0x40``.
+- **address** (*Optional*, integer): Manually specify the I²C address of the sensor. Defaults to ``0x40``.
 - **shunt_resistance** (*Optional*, float): The value of the shunt resistor on the board for current calculation.
   Defaults to ``0.1 ohm``.
 - **max_current** (*Optional*, float): The maximum current you are expecting. ESPHome will use this to
   configure the sensor optimally. Defaults to ``3.2A``.
-- **current** (*Optional*): Use the current value of the sensor in amperes. All options from
-  :ref:`Sensor <config-sensor>`.
-- **power** (*Optional*): Use the power value of the sensor in watts. All options from
-  :ref:`Sensor <config-sensor>`.
-- **bus_voltage** (*Optional*): Use the bus voltage (voltage of the high side contact) value of the sensor in V.
-  All options from :ref:`Sensor <config-sensor>`.
-- **shunt_voltage** (*Optional*): Use the shunt voltage (voltage across the shunt resistor) value of the sensor in V.
-  All options from :ref:`Sensor <config-sensor>`.
+- **adc_time** (*Optional*, :ref:`config-time`): The time in microseconds to perform a single ADC conversion. 
+  Defaults to ``1100us``. Valid values are ``140us``, ``204us``, ``332us``, ``588us``, ``1100us``, ``2116us``, 
+  ``4156us``, ``8244us``.
+- **adc_averaging** (*Optional*, integer): Selects ADC sample averaging count. Defaults to ``4``. Valid values are 
+  ``1``, ``4``, ``16``, ``64``, ``128``, ``256``, ``512``, ``1024``.
 - **update_interval** (*Optional*, :ref:`config-time`): The interval to check the sensor. Defaults to ``60s``.
 
 
+Sensors
+-------
+The component offers four sensors. You can configure all or any subset of them. Each configured sensor 
+is reported  separately on each update_interval. The ``name`` option is required for each sensor configured. 
+All other options from :ref:`Sensor <config-sensor>`.
+
+- **current** (*Optional*): Calculated current output, Amperes. 
+- **power** (*Optional*): Calculated power output, Watts. 
+- **bus_voltage** (*Optional*): Bus voltage output (voltage of the high side contact), Volts.
+- **shunt_voltage** (*Optional*): Shunt voltage (voltage across the shunt resistor) value of the sensor, Volts.
+
+
 See Also
 --------