Merge branch 'current' into beta

components/cover/he60r.rst

@@ -26,8 +26,8 @@ below for a sample hardware interface.
         baud_rate: 1200
         parity: even
         stop_bits: 1
-        tx_pin: REPLACEME
+        tx_pin: GPIOXX
-        rx_pin: REPLACEME
+        rx_pin: GPIOXX
 
     cover:
       platform: he60r
@@ -72,9 +72,9 @@ Note that this circuit inverts the TX line. A configuration for this would look
         parity: even
         stop_bits: 1
         tx_pin:
-          number: REPLACEME
+          number: GPIOXX
           inverted: true
-        rx_pin: REPLACEME
+        rx_pin: GPIOXX
 
     cover:
       platform: he60r
@@ -84,7 +84,7 @@ Note that this circuit inverts the TX line. A configuration for this would look
     binary_sensor:
       - platform: gpio
         pin:
-          number: REPLACEME
+          number: GPIOXX
           inverted: true
           mode:
             input: true

components/dfrobot_sen0395.rst

@@ -36,7 +36,7 @@ a :doc:`/components/uart` component (and its requisite GPIO pins) is required in
         name: Mmwave Detected via GPIO
         device_class: motion
         pin:
-          number: REPLACEME
+          number: GPIOXX
           mode: INPUT_PULLDOWN
 
     switch:
@@ -97,7 +97,7 @@ If you don't want/need to change the radar's settings and only need to determine
         name: Presence Detected via GPIO
         device_class: motion
         pin:
-          number: REPLACEME
+          number: GPIOXX
           mode: INPUT_PULLDOWN
 
 .. _dfrobot_sen0395-via_uart:

components/micronova.rst

@@ -55,7 +55,7 @@ Component/Hub
 .. code-block:: yaml
 
     micronova:
-      enable_rx_pin: REPLACEME
+      enable_rx_pin: GPIOXX
 
 Configuration variables:
 ~~~~~~~~~~~~~~~~~~~~~~~~

components/output/my9231.rst

@@ -94,7 +94,7 @@ complete configuration for a Sonoff B1 looks like:
 .. code-block:: yaml
 
     esphome:
-      name: REPLACEME
+      name: GPIOXX
 
     esp8266:
       board: esp01_1m
@@ -135,7 +135,7 @@ complete configuration for a Sonoff B1 looks like:
 
     light:
       - platform: rgbww
-        name: REPLACEME
+        name: GPIOXX
         red: output_red
         green: output_green
         blue: output_blue
@@ -149,7 +149,7 @@ And here is a complete configuration for the AiThinker AiLight:
 .. code-block:: yaml
 
     esphome:
-      name: REPLACEME
+      name: GPIOXX
 
     esp8266:
       board: esp01_1m
@@ -187,7 +187,7 @@ And here is a complete configuration for the AiThinker AiLight:
 
     light:
       - platform: rgbw
-        name: REPLACEME
+        name: GPIOXX
         red: output_red
         green: output_green
         blue: output_blue

components/output/sm16716.rst

@@ -93,8 +93,8 @@ A complete configuration for a Feit Electric A19 looks like:
 .. code-block:: yaml
 
     esphome:
-      name: REPLACEME
+      name: GPIOXX
-      friendly_name: REPLACEME
+      friendly_name: GPIOXX
 
     esp8266:
       board: esp01_1m

components/sensor/ld2410.rst

@@ -454,7 +454,7 @@ under account, you can set up a :ref:`GPIO Binary Sensor <gpio-binary-sensor>`:
 
     binary_sensor:
       - platform: gpio
-        pin: REPLACEME
+        pin: GPIOXX
         name: gpio out pin presence
         device_class: presence
 

components/touchscreen/cst226.rst

@@ -33,12 +33,27 @@ Configuration variables:
 ************************
 
 - **id** (*Optional*, :ref:`config-id`): Manually set the ID of this touchscreen.
-- **interrupt_pin** (**Required**, :ref:`Pin Schema <config-pin_schema>`): The touch detection pin.
+- **interrupt_pin** (*Optional*, :ref:`Pin Schema <config-pin_schema>`): The touch detection pin.
-- **rotation** (*Optional*): Set the rotation of the touchscreen. By default this will be set to match the display associated with the touchscreen, but this allows more control. Choices are ``0``, ``90``, ``180`` and ``270``.
+- **reset_pin** (*Optional*, :ref:`Pin Schema <config-pin_schema>`): The chip reset pin.
 
 - All other options from :ref:`Touchscreen <config-touchscreen>`.
 
 
+Sample config for the T4-S3
+***************************
+
+.. code-block:: yaml
+
+    i2c:
+      sda: GPIO6
+      scl: GPIO7
+    
+    touchscreen:
+      - platform: cst226
+        id: my_touchscreen
+        interrupt_pin: GPIO8
+        reset_pin: GPIO17
+
 See Also
 --------
 

components/touchscreen/cst816.rst

@@ -36,7 +36,7 @@ Configuration variables:
 
 - **id** (*Optional*, :ref:`config-id`): Manually set the ID of this touchscreen.
 - **interrupt_pin** (*Optional*, :ref:`Pin Schema <config-pin_schema>`): The touch detection pin.
-- **reset_pin** (**Optional**, :ref:`Pin Schema <config-pin_schema>`): The chip reset pin.
+- **reset_pin** (*Optional*, :ref:`Pin Schema <config-pin_schema>`): The chip reset pin.
 
 - All other options from :ref:`Touchscreen <config-touchscreen>`.
 
@@ -61,6 +61,19 @@ Configuration variables:
 
 - All other options from :ref:`Binary Sensor <config-binary_sensor>`.
 
+Sample config for the T-Display S3 AMOLED
+*****************************************
+
+.. code-block:: yaml
+
+    i2c:
+      sda: GPIO3
+      scl: GPIO2
+
+    touchscreen:
+      - platform: cst816
+        id: my_touchscreen
+        interrupt_pin: GPIO21
 
 See Also
 --------

components/touchscreen/gt911.rst

@@ -33,8 +33,7 @@ Configuration variables:
 ************************
 
 - **id** (*Optional*, :ref:`config-id`): Manually set the ID of this touchscreen.
-- **interrupt_pin** (**Required**, :ref:`Pin Schema <config-pin_schema>`): The touch detection pin.
+- **interrupt_pin** (*Optional*, :ref:`Pin Schema <config-pin_schema>`): The touch detection pin.
-- **rotation** (*Optional*): Set the rotation of the touchscreen. By default this will be set to match the display associated with the touchscreen, but this allows more control. Choices are ``0``, ``90``, ``180`` and ``270``.
 
 - All other options from :ref:`Touchscreen <config-touchscreen>`.
 

components/touchscreen/lilygo_t5_47.rst

@@ -15,7 +15,7 @@ The :ref:`I²C <i2c>` is required to be set up in your configuration for this to
     # Example configuration entry
     touchscreen:
       - platform: lilygo_t5_47
-        interrupt_pin: GPIO13
+        interrupt_pin: GPIOXX
 
 
 Configuration variables:

components/touchscreen/xpt2046.rst

@@ -60,17 +60,17 @@ Base Configuration:
 - **threshold** (*Optional*, int): The value to detect the touch or release. Defaults to ``400``.
 
 
-- **calibration_x_min** (*Depricated*): This value is moved to the ``calibration`` values
+- **calibration_x_min** (*Deprecated*): This value is moved to the ``calibration`` values
 
-- **calibration_x_max** (*Depricated*): This value is moved to the ``calibration`` values.
+- **calibration_x_max** (*Deprecated*): This value is moved to the ``calibration`` values.
 
-- **calibration_y_min** (*Depricated*): This value is moved to the ``calibration`` values.
+- **calibration_y_min** (*Deprecated*): This value is moved to the ``calibration`` values.
 
-- **calibration_y_max** (*Depricated*): This value is moved to the ``calibration`` values.
+- **calibration_y_max** (*Deprecated*): This value is moved to the ``calibration`` values.
 
-- **swap_x_y** (*Depricated*): This value is moved to the ``transform`` values as ``swap_xy`` see :ref:`config-touchscreen`.
+- **swap_x_y** (*Deprecated*): This value is moved to the ``transform`` values as ``swap_xy`` see :ref:`config-touchscreen`.
 
-- **report_interval** (*Depricated*): This interval is removed in favor of the ``update_interval``.
+- **report_interval** (*Deprecated*): This interval is removed in favor of the ``update_interval``.
 
 - All other options from :ref:`config-touchscreen`.