mirror of
https://github.com/esphome/esphome-docs.git
synced 2025-03-22 15:19:32 +01:00
Ethernet wESP32 rev 7, AiThinker, SLZB-06 and appearance (#2529)
* Ethernet wESP32 rev 7, AiThinker, SLZB-06 and appearance
This commit is contained in:
H. Árkosi Róbert
GitHub
parent
20a6e1ff58
commit
d931e55d50
@ -32,7 +32,7 @@ Configuration variables:
|
||||
------------------------
|
||||
|
||||
- **type** (**Required**, string): The type of LAN chipset/phy. Must be one of
|
||||
``LAN8720``, ``TLK110`` or ``IP101`` (see datasheet for more details).
|
||||
``LAN8720``, ``RTL8201``, ``DP83848`` or ``IP101``.
|
||||
- **mdc_pin** (**Required**, :ref:`config-pin`): The MDC pin of the board.
|
||||
Usually this is ``GPIO23``.
|
||||
- **mdio_pin** (**Required**, :ref:`config-pin`): The MDIO pin of the board.
|
||||
@ -73,8 +73,10 @@ Configuration variables:
|
||||
clock signal that will not travel reliably over these types of connections. For more
|
||||
information and wiring details refer to the link in the *See also* section.
|
||||
|
||||
Configuration for Olimex ESP32-POE
|
||||
----------------------------------
|
||||
Configuration examples
|
||||
----------------------
|
||||
|
||||
**Olimex ESP32-POE**
|
||||
|
||||
.. code-block:: yaml
|
||||
|
||||
@ -86,8 +88,8 @@ Configuration for Olimex ESP32-POE
|
||||
phy_addr: 0
|
||||
power_pin: GPIO12
|
||||
|
||||
Configuration for Olimex ESP32-EVB
|
||||
----------------------------------
|
||||
|
||||
**Olimex ESP32-EVB**
|
||||
|
||||
.. code-block:: yaml
|
||||
|
||||
@ -98,8 +100,7 @@ Configuration for Olimex ESP32-EVB
|
||||
clk_mode: GPIO0_IN
|
||||
phy_addr: 0
|
||||
|
||||
Configuration for Olimex ESP32-GATEWAY
|
||||
--------------------------------------
|
||||
**Olimex ESP32-GATEWAY**
|
||||
|
||||
.. code-block:: yaml
|
||||
|
||||
@ -110,8 +111,7 @@ Configuration for Olimex ESP32-GATEWAY
|
||||
clk_mode: GPIO17_OUT
|
||||
phy_addr: 0
|
||||
|
||||
Configuration for LILYGO TTGO T-Internet-POE ESP32-WROOM LAN8270A Chip
|
||||
----------------------------------------------------------------------
|
||||
**LILYGO TTGO T-Internet-POE ESP32-WROOM LAN8270A**
|
||||
|
||||
.. code-block:: yaml
|
||||
|
||||
@ -122,8 +122,7 @@ Configuration for LILYGO TTGO T-Internet-POE ESP32-WROOM LAN8270A Chip
|
||||
clk_mode: GPIO17_OUT
|
||||
phy_addr: 0
|
||||
|
||||
Configuration for Wireless Tag WT32-ETH01
|
||||
-----------------------------------------
|
||||
**Wireless Tag WT32-ETH01** and **SMLIGHT SLZB-06**
|
||||
|
||||
.. code-block:: yaml
|
||||
|
||||
@ -135,42 +134,7 @@ Configuration for Wireless Tag WT32-ETH01
|
||||
phy_addr: 1
|
||||
power_pin: GPIO16
|
||||
|
||||
Configuration for OpenHacks LAN8720
|
||||
-----------------------------------
|
||||
|
||||
.. code-block:: yaml
|
||||
|
||||
ethernet:
|
||||
type: LAN8720
|
||||
mdc_pin: GPIO23
|
||||
mdio_pin: GPIO18
|
||||
phy_addr: 1
|
||||
|
||||
.. note::
|
||||
|
||||
This board has an issue that might cause the ESP32 to boot in program mode. When testing, make sure
|
||||
you are monitoring the serial output and reboot the device several times to see if it boots into the
|
||||
program properly.
|
||||
|
||||
Configuration for wESP32 board (up to rev.6)
|
||||
--------------------------------------------
|
||||
|
||||
.. code-block:: yaml
|
||||
|
||||
ethernet:
|
||||
type: LAN8720
|
||||
mdc_pin: GPIO16
|
||||
mdio_pin: GPIO17
|
||||
clk_mode: GPIO0_IN
|
||||
phy_addr: 0
|
||||
|
||||
.. note::
|
||||
|
||||
Revision 7 and upwards of the wESP32 board does not have a LAN8720 chip. Until support for the
|
||||
replacement RTL8201 is included in ESPHome, the wESP board rev.7 will not work with the above configuration.
|
||||
|
||||
Configuration for ESP32-Ethernet-Kit board
|
||||
------------------------------------------
|
||||
**ESP32-Ethernet-Kit**
|
||||
|
||||
.. code-block:: yaml
|
||||
|
||||
@ -183,8 +147,7 @@ Configuration for ESP32-Ethernet-Kit board
|
||||
power_pin: GPIO5
|
||||
|
||||
|
||||
Configuration for M5Stack PoESP32 Unit
|
||||
--------------------------------------
|
||||
**M5Stack PoESP32 Unit**
|
||||
|
||||
.. code-block:: yaml
|
||||
|
||||
@ -196,11 +159,65 @@ Configuration for M5Stack PoESP32 Unit
|
||||
phy_addr: 1
|
||||
power_pin: GPIO5
|
||||
|
||||
**AIThinker ESP32-G Gateway Unit**
|
||||
|
||||
.. code-block:: yaml
|
||||
|
||||
ethernet:
|
||||
type: LAN8720
|
||||
mdc_pin: GPIO23
|
||||
mdio_pin: GPIO18
|
||||
clk_mode: GPIO17_OUT
|
||||
phy_addr: 1
|
||||
power_pin: GPIO5
|
||||
|
||||
**wESP32 board**
|
||||
|
||||
.. code-block:: yaml
|
||||
|
||||
# for board up to rev.5
|
||||
ethernet:
|
||||
type: LAN8720
|
||||
mdc_pin: GPIO16
|
||||
mdio_pin: GPIO17
|
||||
clk_mode: GPIO0_IN
|
||||
phy_addr: 0
|
||||
|
||||
# for board rev.7 and up
|
||||
ethernet:
|
||||
type: RTL8201
|
||||
mdc_pin: GPIO16
|
||||
mdio_pin: GPIO17
|
||||
clk_mode: GPIO0_IN
|
||||
phy_addr: 0
|
||||
|
||||
.. note::
|
||||
|
||||
Revision 5 and below of the wESP32 board use the LAN8720 Ethernet PHY. Revision 7 and newer of it use the RTL8201 Ethernet PHY. Support for RTL8201 is available from ESPHome version 2022.12 upwards.
|
||||
|
||||
**OpenHacks LAN8720**
|
||||
|
||||
.. code-block:: yaml
|
||||
|
||||
ethernet:
|
||||
type: LAN8720
|
||||
mdc_pin: GPIO23
|
||||
mdio_pin: GPIO18
|
||||
phy_addr: 1
|
||||
|
||||
.. note::
|
||||
|
||||
This board has an issue that might cause the ESP32 to boot in program mode. When testing, make sure
|
||||
you are monitoring the serial output and reboot the device several times to see if it boots into the
|
||||
program properly.
|
||||
|
||||
|
||||
|
||||
See Also
|
||||
--------
|
||||
|
||||
- :doc:`network`
|
||||
- :doc:`text_sensor/ethernet_info`
|
||||
- :apiref:`ethernet/ethernet_component.h`
|
||||
- `ESP32 Ethernet PHY connection info <https://pcbartists.com/design/embedded/esp32-ethernet-phy-schematic-design/>`__
|
||||
- :ghedit:`Edit`
|
||||
|
||||
Loading…
Reference in New Issue
Block a user