ESP32 Camera Component
======================

.. seo::
    :description: Instructions for setting up the ESP32 Cameras in ESPHome
    :image: camera.png

The ``esp32_camera`` component allows you to use ESP32-based camera boards in ESPHome that
directly integrate into Home Assistant through the native API.

.. warning::

    Some ESP32 Camera boards have insufficient cooling and will overheat over time,
    ESPHome does only activate the camera when Home Assistant requests an image, but
    the camera until can still heat up considerably for some boards.

    If the camera is not recognized after a reboot and the unit feels warm, try waiting for
    it to cool down and check again - if that still doesn't work try enabling the test pattern.

.. note::

    The example configuration is valid for M5Stack ESP32 camera models.

.. code-block:: yaml

    # Example configuration entry
    esp32_camera:
      name: My Camera
      external_clock:
        pin: GPIO27
        frequency: 20MHz
      i2c_pins:
        sda: GPIO25
        scl: GPIO23
      data_pins: [GPIO17, GPIO35, GPIO34, GPIO5, GPIO39, GPIO18, GPIO36, GPIO19]
      vsync_pin: GPIO22
      href_pin: GPIO26
      pixel_clock_pin: GPIO21
      reset_pin: GPIO15
      resolution: 640x480
      jpeg_quality: 10

Configuration variables:
------------------------

- **name** (**Required**, string): The name of the camera.

Connection Options:

- **data_pins** (**Required**, list of pins): The data lanes of the camera, this must be a list
  of 8 gpio pins.
- **vsync_pin** (**Required**, pin): The pin the VSYNC line of the camera is connected to.
- **href_pin** (**Required**, pin): The pin the HREF line of the camera is connected to.
- **pixel_clock_pin** (**Required**, pin): The pin the pixel clock line of the camera is connected to.
- **external_clock** (**Required**): The configuration of the external clock to drive the camera.

  - **pin** (**Required**, pin): The pin the external clock line is connected to.
  - **frequency** (*Optional*, float): The frequency of the external clock, must be either 20MHz
    or 10MHz. Defaults to ``20MHz``.

- **i2c_pins** (**Required**): The i2c control pins of the camera.

  - **sda** (**Required**, pin): The SDA pin of the i2c interface.
  - **scl** (**Required**, pin): The SCL pin of the i2c interface.

- **reset_pin** (*Optional*, pin): The ESP pin the reset pin of the camera is connected to.
  If set, this will reset the camera before the ESP boots.
- **power_down_pin** (*Optional*, pin): The ESP pin to power down the camera.
  If set, this will power down the camera while it is inactive.
- **test_pattern** (*Optional*, boolean): When enabled, the camera will show a test pattern
  that can be used to debug connection issues.

Frame Settings:

- **max_framerate** (*Optional*, float): The maximum framerate the camera will generate images at.
  Up to 60Hz is possible (with reduced frame sizes), but beware of overheating. Defaults to ``10 fps``.
- **idle_framerate** (*Optional*, float): The framerate to capture images at when no client
  is requesting a full stream. Defaults to ``0.1 fps``.
- **resolution** (*Optional*, enum): The resolution the camera will capture images at. Higher
  resolutions require more memory, if there's not enough memory you will see an error during startup.

    - ``160x120`` (QQVGA)
    - ``128x160`` (QQVGA2)
    - ``176x144`` (QCIF)
    - ``240x176`` (HQVGA)
    - ``320x240`` (QVGA)
    - ``400x296`` (CIF)
    - ``640x480`` (VGA, default)
    - ``800x600`` (SVGA)
    - ``1024x768`` (XGA)
    - ``1280x1024`` (SXGA)
    - ``1600x1200`` (UXGA)

- **jpeg_quality** (*Optional*, int): The JPEG quality that the camera should encode images with.
  From 10 to 63. Defaults to ``10``.

- **contrast** (*Optional*, int): The contrast to apply to the picture, from -2 to 2. Defaults to ``0``.
- **brightness** (*Optional*, int): The brightness to apply to the picture, from -2 to 2. Defaults to ``0``.
- **saturation** (*Optional*, int): The saturation to apply to the picture, from -2 to 2. Defaults to ``0``.
- **vertical_flip** (*Optional*, bool): Whether to flip the image vertically. Defaults to ``true``.
- **horizontal_mirror** (*Optional*, bool): Whether to mirror the image horizontally. Defaults to ``true``.

See Also
--------

- :apiref:`wifi_component.h`
- :ghedit:`Edit`

.. disqus::