ST7789V TFT LCD =============== .. seo:: :description: Instructions for setting up ST7789V TFT LCD display drivers. :image: st7789v.jpg .. _st7789v: Usage ----- The ``st7789v`` display platform allows you to use ST7789V (`datasheet `__, `Tindie `__) displays with ESPHome. Note that this component utilizes the 4-Wire :ref:`SPI bus `. .. figure:: images/st7789v-full.jpg :align: center :width: 75.0% ST7789V TFT LCD on TTGO T-Display module The TTGO T-Display module shown has the display attached to the module's board and its connections to the ESP32 cannot be changed. Other display modules have pin headers or other connectors which must be connected appropriately to an ESP module. .. note:: Displays larger than the 135x240 pixel display on the TTGO T-Display shown require a significant amount of RAM to operate correctly. Some ESP devices, such as the ESP8266, do not have sufficient memory to support this display. If you attempt to use this component and experience repeated crashes, this is likely the cause of the issue. .. code-block:: yaml # Example minimal configuration entry spi: clk_pin: GPIO18 mosi_pin: GPIO19 display: - platform: st7789v model: TTGO TDisplay 135x240 backlight_pin: GPIO4 cs_pin: GPIO5 dc_pin: GPIO16 reset_pin: GPIO23 lambda: |- it.print(0, 0, id(font), "Hello World!"); font: - file: "gfonts://Roboto" id: font size: 20 .. note:: For more information about the font options see: :ref:`display-fonts`. Configuration variables: ************************ Options below marked **Required** might have default values set for some models and do not need to be set. If you do specify them they will override any default. - **model** (**Required**, string): The display model to use. One of the following options: - ``TTGO TDisplay 135x240`` - ``Adafruit Funhouse 240x240`` - ``Adafruit RR 280x240`` (round-rectangular display -- some pixels are "deleted" from corners to form rounded shape) - ``Adafruit S2 TFT FEATHER 240X135`` - ``LILYGO T-Embed 170X320`` - ``Custom`` For other displays not listed above - **height** (**Required**, int): Sets height of display in pixels. Defaults depends ``model``. - **width** (**Required**, int): Sets width of display. Defaults depends ``model``. - **offset_height** (**Required**, int): When ``model`` is set to "Custom", use this to specify the display's vertical offset in pixels. This option may not be specified when the ``model`` is not set to "Custom". Defaults depends ``model``. - **offset_width** (**Required**, int): When ``model`` is set to "Custom", use this to specify the display's horizontal offset in pixels. This option may not be specified when the ``model`` is not set to "Custom". Defaults depends ``model``. - **cs_pin** (**Required**, :ref:`Pin Schema `): The CS pin. Defaults depends ``model``. - **dc_pin** (**Required**, :ref:`Pin Schema `): The DC pin. Defaults depends ``model``. - **reset_pin** (**Required**, :ref:`Pin Schema `): The RESET pin. Defaults depends ``model``. - **eightbitcolor** (*Optional*, boolean): Limits the supported color depth to eight bits. May be useful on memory-constrained devices. Defaults to ``false``. - **backlight_pin** (*Optional*, :ref:`Pin Schema `): The display's backlight pin. May be required depending on the hardware configuration. - **power_supply** (*Optional*, :ref:`config-id`): The :doc:`power supply ` to connect to this display if required by hardware. The power supply will be turned on before attempting to initialize the display. - **lambda** (*Optional*, :ref:`lambda `): The lambda to use for rendering the content on the display. See :ref:`display-engine` for more information. - **update_interval** (*Optional*, :ref:`config-time`): The interval to re-draw the screen. Defaults to ``5s``. - **pages** (*Optional*, list): Show pages instead of a single lambda. See :ref:`display-pages`. - **id** (*Optional*, :ref:`config-id`): Manually specify the ID used for code generation. Preset configuration ******************** For specific models there is some preset configuration which will satisy some of the **Required** *unless preset* values. All models except ``Custom`` preset the ``height``, ``width`` and ``offset_...`` values. The table below summarises the other presets. Note that SPI CLK and SDO (mosi) pins, and the power supply pin must be separately configured in ``spi:`` and ``power_supply:`` blocks - the pins are noted below for convenience only. Items marked RQ are hardware dependent but required and not preset. Items marked ? are optional depending on the hardware. .. list-table:: Model presets :header-rows: 1 * - Model - Height/ width - Offsets - CS - DC - Reset - Back light - Pwr sup - SPI clk - SPI mosi * - TTGO TDisplay 135x240 - 240/135 - 52/40 - 5 - 6 - 23 - 4 - - 18 - 19 * - Adafruit Funhouse 240x240 - 240/240 - 0/0 - 40 - 39 - 41 - 21 - - 36 - 35 * - Adafruit RR 280x240 - 240/240 - 0/20 - RQ - RQ - RQ - ? - ? - RQ - RQ * - Adafruit S2 TFT FEATHER 240X135 - 240/135 - 52/40 - 7 - 39 - 40 - 45 - 21 - 36 - 35 * - LILYGO T-Embed 170X320 - 320/170 - 35/0 - 10 - 13 - 9 - 15 - 46 - 12 - 11 * - Custom - RQ - RQ - RQ - RQ - RQ - ? - ? - RQ - RQ For all boards you can override the presets by specifying any of the configuration options. Pin assignments on some boards can change between versions so if it doesn't work with the presets check the board pinouts and override options as required. .. note:: On memory-constrained devices, it may be possible to use *part* of the display area by specifying a smaller ``height`` and/or ``width`` than that of the actual display. Configuration examples ********************** To use colors in your lambda: .. code-block:: yaml color: - id: my_red red: 100% green: 3% blue: 5% ... display: ... lambda: |- it.rectangle(0, 0, it.get_width(), it.get_height(), id(my_red)); To bring in color images: .. code-block:: yaml image: - file: "image.jpg" id: my_image resize: 200x200 type: RGB24 ... display: ... lambda: |- it.image(0, 0, id(my_image)); Complete example **************** The following is an example YAML configuration that you can add to your base device configuration. It defines: - three fonts (well, one font in three sizes) - a ``binary_sensor`` that indicates the state of connectivity to the API - a ``binary_sensor`` for each of the two buttons on the TTGO module - a ``switch``, allowing control of the backlight from HA - several colors - a color image to be shown on the display - time, for display...on the display - the SPI configuration for communicating with the display - the display component itself, for use on the TTGO module - a lambda which paints the screen as shown in the picture above: - blue borders, with a sort of "title bar" along the top - "ESPHome" in yellow in the top left corner - the API connection status, "Online" in green when connected, "Offline" in red when not - the time and date, more or less in the center of the display To use this example, you need only to provide the font file, "Helvetica.ttf" (or update it to a font of your choosing) and an image file, "image.png" (it may also be a ".jpg"). Place these into the same directory as the YAML configuration file itself. Comment/Uncomment/Modify the appropriate lines of C code in the lambda to hide or show the image or text as you wish. .. code-block:: yaml color: - id: my_red red: 100% green: 0% blue: 0% - id: my_yellow red: 100% green: 100% blue: 0% - id: my_green red: 0% green: 100% blue: 0% - id: my_blue red: 0% green: 0% blue: 100% - id: my_gray red: 50% green: 50% blue: 50% font: - file: "Helvetica.ttf" id: helvetica_48 size: 48 - file: "Helvetica.ttf" id: helvetica_24 size: 24 - file: "Helvetica.ttf" id: helvetica_12 size: 12 binary_sensor: - platform: status name: "Node Status" id: system_status - platform: gpio pin: number: GPIO0 inverted: true mode: input: true pullup: true name: "T-Display Button Input 0" id: tdisplay_button_input_0 - platform: gpio pin: number: GPIO35 inverted: true name: "T-Display Button Input 1" id: tdisplay_button_input_1 # Allow dimmable control of the backlight (pin GPIO4) output: - platform: ledc pin: GPIO4 id: gpio4 light: - platform: monochromatic output: gpio4 name: "Backlight" image: - file: "image.png" id: my_image resize: 200x200 type: RGB24 time: - platform: homeassistant id: esptime spi: clk_pin: GPIO18 mosi_pin: GPIO19 display: - platform: st7789v cs_pin: GPIO5 dc_pin: GPIO16 reset_pin: GPIO23 rotation: 270 lambda: |- it.rectangle(0, 0, it.get_width(), it.get_height(), id(my_blue)); it.rectangle(0, 20, it.get_width(), it.get_height(), id(my_blue)); // header bar it.strftime((240 / 2), (140 / 3) * 1 + 5, id(helvetica_24), id(my_gray), TextAlign::CENTER, "%Y-%m-%d", id(esptime).now()); it.strftime((240 / 2), (140 / 3) * 2 + 5, id(helvetica_48), id(my_gray), TextAlign::CENTER, "%H:%M:%S", id(esptime).now()); it.print(5, 5, id(helvetica_12), id(my_yellow), TextAlign::TOP_LEFT, "ESPHome"); // Comment out the above lines to see the image without text overlaid // it.image(0, 0, id(my_image)); if (id(system_status).state) { it.print(235, 5, id(helvetica_12), id(my_green), TextAlign::TOP_RIGHT, "Online"); } else { it.print(235, 5, id(helvetica_12), id(my_red), TextAlign::TOP_RIGHT, "Offline"); } See Also -------- - :doc:`index` - :doc:`Power Supply Component ` - :apiref:`st7789v_base/st7789v_base.h` - :ghedit:`Edit`