Peacefair PZEM-004T V3 Energy Monitor
=====================================

.. seo::
    :description: Instructions for setting up PZEM-004T power monitors.
    :image: pzem-ac.jpg
    :keywords: PZEM-004T V3

.. note::

    This page is incomplete and could use some work. If you want to contribute, please read the
    :doc:`contributing guide </guides/contributing>`. This page is missing:

      - Images/screenshots/example configs of this device being used in action.

The ``pzemac`` sensor platform allows you to use PZEM-004T V3 energy monitors
(`website <https://innovatorsguru.com/pzem-004t-v3/>`__,
`datasheet <https://innovatorsguru.com/wp-content/uploads/2019/06/PZEM-004T-V3.0-Datasheet-User-Manual.pdf>`__)
with ESPHome.

The sensor can be connected in various configurations - please see the `manufacturer's website <https://innovatorsguru.com/pzem-004t-v3/>`__
for more information.

.. figure:: images/pzem-ac.png
    :align: center
    :width: 80.0%

    PZEM-004T Version 3.

.. warning::

    This page refers to version V3 of the PZEM004T.
    For using the older V1 variant of this sensor please see :doc:`pzem004t <pzem004t>`.

The communication with this integration is done over a :ref:`UART bus <uart>` using :ref:`Modbus <modbus>`.
You must therefore have a ``uart:`` entry in your configuration with both the TX and RX pins set
to some pins on your board and the baud rate set to 9600.

.. code-block:: yaml

    # Example configuration entry
    uart:
      rx_pin: D1
      tx_pin: D2
      baud_rate: 9600

    modbus:

    sensor:
      - platform: pzemac
        current:
          name: "PZEM-004T V3 Current"
        voltage:
          name: "PZEM-004T V3 Voltage"
        energy:
          name: "PZEM-004T V3 Energy"
        power:
          name: "PZEM-004T V3 Power"
        frequency:
          name: "PZEM-004T V3 Frequency"
        power_factor:
          name: "PZEM-004T V3 Power Factor"
        update_interval: 60s

Configuration variables:
------------------------

- **current** (*Optional*): Use the current value of the sensor in amperes. All options from
  :ref:`Sensor <config-sensor>`.
- **energy** (*Optional*): Use the (active) energy value of the sensor in watt*hours. All options from
  :ref:`Sensor <config-sensor>`.
- **power** (*Optional*): Use the (active) power value of the sensor in watts. All options from
  :ref:`Sensor <config-sensor>`.
- **voltage** (*Optional*): Use the voltage value of the sensor in volts.
  All options from :ref:`Sensor <config-sensor>`.
- **frequency** (*Optional*): Use the frequency value of the sensor in hertz.
  All options from :ref:`Sensor <config-sensor>`.
- **power_factor** (*Optional*): Use the power factor value of the sensor.
  All options from :ref:`Sensor <config-sensor>`.
- **update_interval** (*Optional*, :ref:`config-time`): The interval to check the
  sensor. Defaults to ``60s``.
- **address** (*Optional*, int): The address of the sensor if multiple sensors are attached to
  the same UART bus. You will need to set the address of each device manually. Defaults to ``1``.
- **modbus_id** (*Optional*, :ref:`config-id`): Manually specify the ID of the Modbus hub.

.. _pzemac-reset_energy_action:

``pzemac.reset_energy`` Action
******************************

This action resets the total energy value of the pzemac device with the given ID when executed.

.. code-block:: yaml

    on_...:
      then:
        - pzemac.reset_energy: pzemac_1

Changing the address of a PZEM-004T:
------------------------------------

You can use the following configuration to change the address of a sensor.
You must set the ``address`` of the ``modbus_controller`` to the current address, and ``new_address`` of the ``on_boot`` lambda to the new one.

.. warning::

    This should be used only once! After changing the address, this code should be removed from the ESP before using the actual sensor code.

.. code-block:: yaml

    esphome:
      ...
      on_boot:
        ## configure controller settings at setup
        ## make sure priority is lower than setup_priority of modbus_controller
        priority: -100
        then:
          - lambda: |-
              auto new_address = 0x03;

              if(new_address < 0x01 || new_address > 0xF7) // sanity check
              {
                ESP_LOGE("ModbusLambda", "Address needs to be between 0x01 and 0xF7");
                return;
              }

              esphome::modbus_controller::ModbusController *controller = id(pzem);
              auto set_addr_cmd = esphome::modbus_controller::ModbusCommandItem::create_write_single_command(
                controller, 0x0002, new_address);

              delay(200) ;
              controller->queue_command(set_addr_cmd);
              ESP_LOGI("ModbusLambda", "PZEM Addr set");

    modbus:
      send_wait_time: 200ms
      id: mod_bus_pzem

    modbus_controller:
      - id: pzem
        ## the current device addr
        address: 0x1
        modbus_id: mod_bus_pzem
        command_throttle: 0ms
        setup_priority: -10
        update_interval: 30s


See Also
--------

- :ref:`sensor-filters`
- :doc:`pzem004t`
- :doc:`pzemdc`
- :apiref:`pzemac/pzemac.h`
- :ghedit:`Edit`