mirror of
https://github.com/esphome/esphome-docs.git
synced 2024-11-09 10:02:45 +01:00
120 lines
3.8 KiB
ReStructuredText
120 lines
3.8 KiB
ReStructuredText
ADE7953 Power Sensor
|
|
====================
|
|
|
|
.. seo::
|
|
:description: Instructions for setting up ADE7953 power sensors
|
|
:image: ade7953.png
|
|
|
|
.. note::
|
|
|
|
This page is incomplete and could some work. If you want to contribute, please read the
|
|
:doc:`contributing guide </guides/contributing>`. This page is missing:
|
|
|
|
- A complete configuration example for the Shelly 2.5
|
|
- An image for the front page
|
|
|
|
The ``ade7953`` sensor platform allows you to use ADE7953 single phase energy metering ICs
|
|
(`datasheet <https://www.analog.com/media/en/technical-documentation/data-sheets/ADE7953.pdf>`__)
|
|
with ESPHome. These are commonly found in **Shelly 2.5** devices.
|
|
|
|
This sensor can measure voltage and has two channels for reading current and active power (A & B).
|
|
|
|
The :ref:`I²C Bus <i2c>` is
|
|
required to be set up in your configuration for this sensor to work.
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Example configuration entry
|
|
sensor:
|
|
- platform: ade7953
|
|
voltage:
|
|
name: ADE7953 Voltage
|
|
current_a:
|
|
name: ADE7953 Current A
|
|
current_b:
|
|
name: ADE7953 Current B
|
|
active_power_a:
|
|
name: ADE7953 Active Power A
|
|
active_power_b:
|
|
name: ADE7953 Active Power B
|
|
update_interval: 60s
|
|
|
|
Configuration variables:
|
|
------------------------
|
|
|
|
- **address** (*Optional*, int): Manually specify the I^2C address of the sensor. Defaults to ``0x38``.
|
|
- **voltage** (*Optional*): Use the voltage value of the sensor in volt. All options from
|
|
:ref:`Sensor <config-sensor>`.
|
|
- **current_a** (*Optional*): Use the current value of the A channel in amperes. All options from
|
|
:ref:`Sensor <config-sensor>`.
|
|
- **current_b** (*Optional*): Use the current value of the B channel in amperes. All options from
|
|
:ref:`Sensor <config-sensor>`.
|
|
- **active_power_a** (*Optional*): Use the power value of the A channel in watts. All options from
|
|
:ref:`Sensor <config-sensor>`.
|
|
- **active_power_b** (*Optional*): Use the power value of the A channel in watts. All options from
|
|
:ref:`Sensor <config-sensor>`.
|
|
- **update_interval** (*Optional*, :ref:`config-time`): The interval to check the sensor. Defaults to ``60s``.
|
|
|
|
Use with Shelly 2.5
|
|
-------------------
|
|
|
|
The Shelly 2.5 device contains this sensor for power monitoring. An example config for the Shelly 2.5
|
|
is given below.
|
|
|
|
There are two oddities with the Shelly 2.5:
|
|
|
|
- First, the A and B channels are mixed up - the chip's A channel is label B on the outside and
|
|
vice versa. Probably to make the PCB easier to manufacture.
|
|
- Secondly, due to the first point the active_power values are inverted. This is fixed by
|
|
using a multiply filter as seen in the config below.
|
|
|
|
Additionally, the device has an ::doc:`NTC temperature sensor <ntc>`.
|
|
|
|
.. code-block:: yaml
|
|
|
|
i2c:
|
|
sda: GPIO12
|
|
scl: GPIO14
|
|
|
|
sensor:
|
|
- platform: ade7953
|
|
voltage:
|
|
name: Shelly Voltage
|
|
current_a:
|
|
name: Shelly Current B
|
|
current_b:
|
|
name: Shelly Current A
|
|
active_power_a:
|
|
name: Shelly Active Power B
|
|
filters:
|
|
- multiply: -1
|
|
active_power_b:
|
|
name: Shelly Active Power A
|
|
filters:
|
|
- multiply: -1
|
|
update_interval: 60s
|
|
|
|
# NTC Temperature
|
|
- platform: ntc
|
|
sensor: temp_resistance_reading
|
|
name: "Shelly Temperature"
|
|
calibration:
|
|
b_constant: 3350
|
|
reference_resistance: 10kOhm
|
|
reference_temperature: 298.15K
|
|
- platform: resistance
|
|
id: temp_resistance_reading
|
|
sensor: temp_analog_reading
|
|
configuration: DOWNSTREAM
|
|
resistor: 32kOhm
|
|
- platform: adc
|
|
id: temp_analog_reading
|
|
pin: A0
|
|
|
|
See Also
|
|
--------
|
|
|
|
- :ref:`sensor-filters`
|
|
- :apiref:`ade7953/ade7953.h`
|
|
- :ghedit:`Edit`
|