esphome-docs/components/sensor/ld2410.rst

LD2410 Sensor
=============

.. seo::
    :description: Instructions for setting up LD2410 sensors.
    :image: ld2410.jpg

Component/Hub
-------------
.. _ld2410-component:

The ``ld2410`` sensor platform allows you to use HI-LINK LD2410 motion and presence sensor.
(`datasheet and user manual <https://drive.google.com/drive/folders/1p4dhbEJA3YubyIjIIC7wwVsSo8x29Fq-?spm=a2g0o.detail.1000023.17.93465697yFwVxH>`__) with ESPHome.
The :ref:`UART <uart>` is required to be set up in your configuration for this sensor to work.

Use of hardware UART pins is highly recommended, in order to support the out-of-the-box 256000 baud rate of the LD2410 sensor.

.. figure:: images/ld2410.jpg
    :align: center
    :width: 50.0%

    LD2410 motion and presence sensor

.. code-block:: yaml

    # Example configuration entry
    uart:
      tx_pin: REPLACEME
      rx_pin: REPLACEME
      baud_rate: 256000
      parity: NONE
      stop_bits: 1

    ld2410:
      timeout: 150s
      max_move_distance : 6m
      max_still_distance: 0.75m
      g0_move_threshold: 10
      g0_still_threshold: 20
      g1_move_threshold: 10
      g1_still_threshold: 20
      g2_move_threshold: 20
      g2_still_threshold: 21
      g3_move_threshold: 30
      g3_still_threshold: 31
      g4_move_threshold: 40
      g4_still_threshold: 41
      g5_move_threshold: 50
      g5_still_threshold: 51
      g6_move_threshold: 60
      g6_still_threshold: 61
      g7_move_threshold: 70
      g7_still_threshold: 71
      g8_move_threshold: 80
      g8_still_threshold: 81


.. note::

    For UART configuration, ``baud_rate``, ``parity`` and ``stop_bits`` **must be** respectively ``256000``, ``NONE`` and ``1``.

    Use of hardware UART pins is highly recommended, in order to support the out-of-the-box 256000 baud rate of the LD2410 sensor.

Configuration variables:
************************

The configuration is made up of three parts: The central component, individual sensors,
and binary sensors.

- **timeout** (*Optional*, int): Time in seconds during which presence state will stay present
  after leaving. Defaults to ``5s``.
- **max_move_distance** (*Optional*, int): Maximum distance for movement detection.
  Value between ``0.75m`` and ``6m`` inclusive. Defaults to ``4.5m``.
- **max_still_distance** (*Optional*, int): Maximum distance for still detection.
  Value between ``0.75m`` and ``6m`` inclusive. Defaults to ``4.5m``.
- **gX_move_threshold** (*Optional*, int): Threshold for the Xth gate for motion detection (X => 0 to 8).
  Above this level for the considered gate (distance), movement detection will be triggered. Defaults to ``see table below``.
- **gX _still_threshold** (*Optional*, int): Threshold for the Xth gate for still detection. (X => 0 to 8).
  Above this level for the considered gate (distance), still detection will be triggered. Defaults to ``see table below``.

.. list-table:: Default values for gate threshold
    :widths: 25 25 25
    :header-rows: 1

    * - Gate
      - Default Move threshold
      - Default Still threshold
    * - 0
      - 50
      - 0
    * - 1
      - 50
      - 0
    * - 2
      - 40
      - 40
    * - 3
      - 40
      - 40
    * - 4
      - 40
      - 40
    * - 5
      - 40
      - 40
    * - 6
      - 30
      - 15
    * - 7
      - 30
      - 15
    * - 8
      - 30
      - 15

Sensor
------

The ``ld2410`` sensor allows you to use your :doc:`ld2410` to perform different
measurements.

.. code-block:: yaml

    sensor:
      - platform: ld2410
        moving_distance:
          name : Moving Distance
        still_distance:
          name: Still Distance
        moving_energy:
          name: Move Energy
        still_energy:
          name: Still Energy
        detection_distance:
          name: Detection Distance

Configuration variables:
************************

- **moving_distance** (*Optional*): Distance of detected moving target.
  All options from :ref:`Sensor <config-sensor>`.
- **still_distance** (*Optional*): Distance of detected still target.
  All options from :ref:`Sensor <config-sensor>`.
- **moving_energy** (*Optional*): Energy for moving target.
  All options from :ref:`Sensor <config-sensor>`.
- **still_energy** (*Optional*): Energy for still target.
  All options from :ref:`Sensor <config-sensor>`.
- **detection_distance** (*Optional*): Distance in cm of target.
  All options from :ref:`Sensor <config-sensor>`.

Binary Sensor
-------------

The ``ld2410`` binary sensor allows you to use your :doc:`ld2410` to perform different
measurements.

.. code-block:: yaml

    binary_sensor:
      - platform: ld2410
        has_target:
          name: Presence
        has_moving_target:
          name: Moving Target
        has_still_target:
          name: Still Target

Configuration variables:
************************

- **has_target** (*Optional*): If true target detect either still or in movement.
  All options from :ref:`Binary Sensor <config-binary_sensor>`.
- **has_moving_target** (*Optional*): If true a moving target is detected.
  All options from :ref:`Binary Sensor <config-binary_sensor>`.
- **has_still_target** (*Optional*): If true a still target is detected.
  All options from :ref:`Binary Sensor <config-binary_sensor>`.


See Also
--------

- `Official Datasheet and user manuals <https://drive.google.com/drive/folders/1p4dhbEJA3YubyIjIIC7wwVsSo8x29Fq->`_
- `Source of inspiration for implementation <https://github.com/rain931215/ESPHome-LD2410>`_
- :apiref:`ld2410/ld2410.h`
- :ghedit:`Edit`