mirror of
https://github.com/esphome/esphome-docs.git
synced 2024-11-16 10:55:21 +01:00
69 lines
2.4 KiB
ReStructuredText
69 lines
2.4 KiB
ReStructuredText
Belling BL0942 Energy Monitor
|
|
==================================
|
|
|
|
.. seo::
|
|
:description: Instructions for setting up BL0942 power monitors.
|
|
:image: bl0942.png
|
|
:keywords: BL0942, Aubess, Mini Smart Switch With Energy Monitor
|
|
|
|
The ``bl0942`` sensor platform allows you to use BL0942 energy monitors sensors with
|
|
ESPHome. These are used in some Tuya-devices (e.g. Aubess Tuya WiFi Mini Smart Switch With Energy Monitor)
|
|
|
|
The communication with this integration is done over a :ref:`UART bus <uart>`.
|
|
You must therefore have a ``uart:`` entry in your configuration with both the TX and RX pins set
|
|
to some pins on your board and the baud rate set to 4800 with 1 stop bit.
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Example configuration entry
|
|
uart:
|
|
id: uart_bus
|
|
tx_pin: TX
|
|
rx_pin: RX
|
|
baud_rate: 4800
|
|
stop_bits: 1
|
|
|
|
sensor:
|
|
- platform: bl0942
|
|
uart_id: uart_bus
|
|
voltage:
|
|
name: 'BL0942 Voltage'
|
|
current:
|
|
name: 'BL0942 Current'
|
|
power:
|
|
name: 'BL0942 Power'
|
|
filters:
|
|
multiply: -1
|
|
energy:
|
|
name: 'BL0942 Energy'
|
|
frequency:
|
|
name: "BL0942 Frequency"
|
|
accuracy_decimals: 2
|
|
|
|
update_interval: 60s
|
|
|
|
Configuration variables:
|
|
------------------------
|
|
|
|
- **voltage** (*Optional*): The voltage value of the sensor in Volts.
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
- **current** (*Optional*): The current value of the sensor in Amperes. All options from
|
|
:ref:`Sensor <config-sensor>`.
|
|
- **power** (*Optional*): The (active) power value of the sensor in Watts. Note that some power meters will report this in negative values (probably wired backwards), so you may want to use a filter to multiply it by -1. All options from :ref:`Sensor <config-sensor>`.
|
|
- **energy** (*Optional*): Use the voltage value of the sensor in kWh.
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
- **frequency** (*Optional*): The frequency value of the sensor in Hertz. All options from
|
|
:ref:`Sensor <config-sensor>`.
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
- **update_interval** (*Optional*, :ref:`config-time`): The interval to check the
|
|
sensor. Defaults to ``60s``.
|
|
- **uart_id** (*Optional*, :ref:`config-id`): Manually specify the ID of the :ref:`UART Component <uart>` if you want
|
|
to use multiple UART buses.
|
|
|
|
See Also
|
|
--------
|
|
|
|
- :ref:`sensor-filters`
|
|
- :apiref:`bl0942/bl0942.h`
|
|
- :ghedit:`Edit`
|