mirror of
https://github.com/esphome/esphome-docs.git
synced 2024-11-17 11:05:39 +01:00
72 lines
2.5 KiB
ReStructuredText
72 lines
2.5 KiB
ReStructuredText
.. _i2c:
|
|
|
|
I²C Bus
|
|
=======
|
|
|
|
.. seo::
|
|
:description: Instructions for setting up the I²C bus to communicate with 2-wire devices in ESPHome
|
|
:image: i2c.svg
|
|
:keywords: i2c, iic, bus
|
|
|
|
This component sets up the I²C bus for your ESP32 or ESP8266. In order for these components
|
|
to work correctly, you need to define the I²C bus in your configuration. Please note the ESP
|
|
will enable its internal 10kΩ pullup resistors for these pins, so you usually don't need to
|
|
put on external ones. You can use multiple devices on one I²C bus as each device is given a
|
|
unique address for communicating between it and the ESP. You can do this by hopping
|
|
wires from the two lines (SDA and SCL) from each device board to the next device board or by
|
|
connecting the wires from each device back to the two I²C pins on the ESP.
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Example configuration entry for ESP32
|
|
i2c:
|
|
sda: 21
|
|
scl: 22
|
|
scan: true
|
|
id: bus_a
|
|
|
|
Configuration variables:
|
|
------------------------
|
|
|
|
- **sda** (*Optional*, :ref:`config-pin`): The pin for the data line of the I²C bus.
|
|
Defaults to the default of your board (usually GPIO21 for ESP32 and GPIO4 for ESP8266).
|
|
- **scl** (*Optional*, :ref:`config-pin`): The pin for the clock line of the I²C bus.
|
|
Defaults to the default of your board (usually GPIO22 for ESP32 and
|
|
GPIO5 for ESP8266).
|
|
- **scan** (*Optional*, boolean): If ESPHome should do a search of the I²C address space on startup.
|
|
Defaults to ``true``.
|
|
- **frequency** (*Optional*, float): Set the frequency the I²C bus should operate on.
|
|
Defaults to ``50kHz``. Values are ``10kHz``, ``50kHz``, ``100kHz``, ``200kHz``, ... ``800kHz``
|
|
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID for this I²C bus if you need multiple I²C buses.
|
|
|
|
.. note::
|
|
|
|
If the device can support multiple I²C buses (ESP32 has 2, ESP8266 does not support more than one) these buses need to be defined as below and sensors need to be setup specifying the correct bus:
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Example configuration entry
|
|
i2c:
|
|
- id: bus_a
|
|
sda: 13
|
|
scl: 16
|
|
scan: true
|
|
- id: bus_b
|
|
sda: 14
|
|
scl: 15
|
|
scan: true
|
|
# Sensors should be specified as follows
|
|
- platform: bme680
|
|
i2c_id: bus_b
|
|
address: 0x76
|
|
# ...
|
|
|
|
For I2C multiplexing see :doc:`/components/tca9548a`.
|
|
|
|
See Also
|
|
--------
|
|
|
|
- :doc:`/components/tca9548a`
|
|
- :apiref:`i2c/i2c.h`
|
|
- :ghedit:`Edit`
|