mirror of
https://github.com/esphome/esphome-docs.git
synced 2024-09-06 00:58:07 +02:00
599 lines
21 KiB
ReStructuredText
599 lines
21 KiB
ReStructuredText
Remote Transmitter
|
|
==================
|
|
|
|
.. seo::
|
|
:description: Instructions for setting up switches that send out pre-defined sequences of IR or RF signals
|
|
:image: remote.png
|
|
:keywords: Infrared, IR, RF, Remote, TX
|
|
|
|
The ``remote_transmitter`` component lets you send digital packets to control
|
|
devices in your home. For example this includes infrared data or 433MHz RF signals.
|
|
|
|
First, you need to setup a global hub that specifies which pin your remote
|
|
sender is connected to. Then you can use the available actions to send encoded
|
|
remote signals.
|
|
|
|
**See** :ref:`remote-setting-up-infrared` **and** :ref:`remote-setting-up-rf` **for set up guides.**
|
|
|
|
.. note::
|
|
|
|
This component is more accurate on the ESP32, since that chipset has a dedicated
|
|
peripheral for sending exact signal sequences.
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Example configuration entry
|
|
remote_transmitter:
|
|
pin: GPIO32
|
|
carrier_duty_percent: 50%
|
|
|
|
# Individual switches
|
|
switch:
|
|
- platform: template
|
|
name: "Panasonic TV Off"
|
|
turn_on_action:
|
|
remote_transmitter.transmit_panasonic:
|
|
address: 0x4004
|
|
command: 0x100BCBD
|
|
|
|
Configuration variables:
|
|
------------------------
|
|
|
|
- **pin** (**Required**, :ref:`config-pin`): The pin to transmit the remote signal on.
|
|
- **carrier_duty_percent** (*Optional*, int): How much of the time the remote is on. For example, infrared
|
|
protocols modulate the signal using a carrier signal. Set this is ``50%`` if you're working with IR LEDs and to
|
|
``100%`` if working with other things like 433MHz transmitters.
|
|
- **id** (*Optional*, :ref:`config-id`): Manually specify
|
|
the ID used for code generation. Use this if you have multiple remote transmitters.
|
|
|
|
.. _remote_transmitter-transmit_action:
|
|
|
|
Remote Transmitter Actions
|
|
--------------------------
|
|
|
|
Remote transmitters support a number of :ref:`actions <config-action>` that can be used
|
|
to send remote codes. All supported protocols are listed below. All actions additionally
|
|
have these configuration variables:
|
|
|
|
.. code-block::yaml
|
|
|
|
on_...:
|
|
- remote_transmitter.transmit_x:
|
|
# ...
|
|
repeat:
|
|
times: 5
|
|
wait_time: 10ms
|
|
|
|
Configuration variables:
|
|
|
|
- **repeat** (*Optional*): Optionally set the code to be repeated a number of times.
|
|
Defaults to sending the code only once.
|
|
|
|
- **times** (int): The number of times to repeat the code.
|
|
- **wait_time** (:ref:`config-time`): The time to wait between repeats.
|
|
|
|
- **transmitter_id** (*Optional*, :ref:`config-id`): The remote transmitter to send the
|
|
remote code with. Defaults to the first one defined in the configuration.
|
|
|
|
If you're looking for the same functionality as is default in the ``rpi_rf`` integration in
|
|
Home Assistant, you'll want to set the **times** to 10 and the **wait_time** to 0s.
|
|
|
|
If you're looking for the same functionality as is default in the ``rpi_rf`` integration in
|
|
Home Assistant, you'll want to set the **times** to 10 and the **wait_time** to 0s.
|
|
|
|
.. _remote_transmitter-transmit_raw:
|
|
|
|
``remote_transmitter.transmit_raw`` Action
|
|
******************************************
|
|
|
|
This :ref:`action <config-action>` sends a raw code to a remote transmitter.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
- remote_transmitter.transmit_raw:
|
|
code: [4088, -1542, 1019, -510, 513, -1019, 510, -509, 511, -510, 1020,
|
|
-1020, 1022, -1019, 510, -509, 511, -510, 511, -509, 511, -510,
|
|
1020, -1019, 510, -511, 1020, -510, 512, -508, 510, -1020, 1022,
|
|
-1021, 1019, -1019, 511, -510, 510, -510, 1022, -1020, 1019,
|
|
-1020, 511, -511, 1018, -1022, 1020, -1019, 1021, -1019, 1020,
|
|
-511, 510, -1019, 1023, -1019, 1019, -510, 512, -508, 510, -511,
|
|
512, -1019, 510, -509]
|
|
|
|
Configuration variables:
|
|
|
|
- **code** (**Required**, list): The raw code to send as a list of integers.
|
|
Positive numbers represent a digital high signal and negative numbers a digital low signal.
|
|
The number itself encodes how long the signal should last (in microseconds).
|
|
- **carrier_frequency** (*Optional*, float): Optionally set a frequency to send the signal
|
|
with for infrared signals. Defaults to ``0Hz``.
|
|
- All other options from :ref:`remote_transmitter-transmit_action`.
|
|
|
|
``remote_transmitter.transmit_jvc`` Action
|
|
******************************************
|
|
|
|
This :ref:`action <config-action>` sends a JVC infrared remote code to a remote transmitter.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
- remote_transmitter.transmit_jvc:
|
|
data: 0x1234
|
|
|
|
Configuration variables:
|
|
|
|
- **data** (**Required**, int): The JVC code to send, see dumper output for more info.
|
|
|
|
``remote_transmitter.transmit_lg`` Action
|
|
*****************************************
|
|
|
|
This :ref:`action <config-action>` sends an LG infrared remote code to a remote transmitter.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
- remote_transmitter.transmit_lg:
|
|
data: 0x1234567
|
|
nbits: 28
|
|
|
|
Configuration variables:
|
|
|
|
- **data** (**Required**, int): The LG code to send, see dumper output for more info.
|
|
- **nbits** (*Optional*, int): The number of bits to send. Defaults to ``28``.
|
|
- All other options from :ref:`remote_transmitter-transmit_action`.
|
|
|
|
``remote_transmitter.transmit_nec`` Action
|
|
******************************************
|
|
|
|
This :ref:`action <config-action>` sends an NEC infrared remote code to a remote transmitter.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
- remote_transmitter.transmit_nec:
|
|
address: 0x1234
|
|
command: 0x78AB
|
|
|
|
Configuration variables:
|
|
|
|
- **address** (**Required**, int): The address to send, see dumper output for more details.
|
|
- **command** (**Required**, int): The NEC command to send.
|
|
- All other options from :ref:`remote_transmitter-transmit_action`.
|
|
|
|
``remote_transmitter.transmit_sony`` Action
|
|
*******************************************
|
|
|
|
This :ref:`action <config-action>` a Sony infrared remote code to a remote transmitter.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
- remote_transmitter.transmit_sony:
|
|
data: 0x123
|
|
nbits: 12
|
|
|
|
Configuration variables:
|
|
|
|
- **data** (**Required**, int): The Sony code to send, see dumper output for more info.
|
|
- **nbits** (*Optional*, int): The number of bits to send. Defaults to ``12``.
|
|
- All other options from :ref:`remote_transmitter-transmit_action`.
|
|
|
|
``remote_transmitter.transmit_rc5`` Action
|
|
******************************************
|
|
|
|
This :ref:`action <config-action>` sends an RC5 infrared remote code to a remote transmitter.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
- remote_transmitter.transmit_rc5:
|
|
address: 0x1F
|
|
command: 0x3F
|
|
|
|
Configuration variables:
|
|
|
|
- **address** (**Required**, int): The address to send, see dumper output for more details.
|
|
- **command** (**Required**, int): The RC5 command to send.
|
|
- All other options from :ref:`remote_transmitter-transmit_action`.
|
|
|
|
``remote_transmitter.transmit_samsung`` Action
|
|
**********************************************
|
|
|
|
This :ref:`action <config-action>` sends a Samsung infrared remote code to a remote transmitter.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
- remote_transmitter.transmit_samsung:
|
|
data: 0x1FEF05E4
|
|
|
|
Configuration variables:
|
|
|
|
- **data** (**Required**, int): The data to send, see dumper output for more details.
|
|
- All other options from :ref:`remote_transmitter-transmit_action`.
|
|
|
|
``remote_transmitter.transmit_samsung36`` Action
|
|
************************************************
|
|
|
|
This :ref:`action <config-action>` sends a Samsung36 infrared remote code to a remote transmitter.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
- remote_transmitter.transmit_samsung36:
|
|
address: 0x0400
|
|
command: 0x000E00FF
|
|
|
|
Configuration variables:
|
|
|
|
- **address** (**Required**, int): The address to send, see dumper output for more details.
|
|
- **command** (**Required**, int): The Samsung36 command to send, see dumper output for more details.
|
|
- All other options from :ref:`remote_transmitter-transmit_action`.
|
|
|
|
``remote_transmitter.transmit_panasonic`` Action
|
|
************************************************
|
|
|
|
This :ref:`action <config-action>` sends a Panasonic infrared remote code to a remote transmitter.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
- remote_transmitter.transmit_panasonic:
|
|
address: 0x1FEF
|
|
command: 0x1F3E065F
|
|
|
|
Configuration variables:
|
|
|
|
- **address** (**Required**, int): The address to send the command to, see dumper output for more details.
|
|
- **command** (**Required**, int): The command to send.
|
|
- All other options from :ref:`remote_transmitter-transmit_action`.
|
|
|
|
``remote_transmitter.transmit_pioneer`` Action
|
|
**********************************************
|
|
|
|
This :ref:`action <config-action>` sends a Pioneer infrared remote code to a remote transmitter.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
- remote_transmitter.transmit_pioneer:
|
|
rc_code_1: 0xA556
|
|
rc_code_2: 0xA506
|
|
repeat:
|
|
times: 2
|
|
|
|
Configuration variables:
|
|
|
|
- **rc_code_1** (**Required**, int): The remote control code to send, see dumper output for more details.
|
|
- **rc_code_2** (*Optional*, int): The secondary remote control code to send; some codes are sent in
|
|
two parts.
|
|
- Note that ``repeat`` is still optional, however **Pioneer devices may require that a given code is
|
|
received multiple times before they will act on it.** Add this if your device does not respond to
|
|
commands sent with this action.
|
|
- All other options from :ref:`remote_transmitter-transmit_action`.
|
|
|
|
At the time this action was created, Pioneer maintained listings of IR codes used for their devices
|
|
`here <https://www.pioneerelectronics.com/PUSA/Support/Home-Entertainment-Custom-Install/IR+Codes>`__.
|
|
If unable to find your specific device in the documentation, find a device in the same class; the codes
|
|
are largely shared among devices within a given class.
|
|
|
|
``remote_transmitter.transmit_rc_switch_raw`` Action
|
|
****************************************************
|
|
|
|
This :ref:`action <config-action>` sends a raw RC-Switch code to a
|
|
remote transmitter.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
- remote_transmitter.transmit_rc_switch_raw:
|
|
code: '001010011001111101011011'
|
|
protocol: 1
|
|
|
|
Configuration variables:
|
|
|
|
- **code** (**Required**, string): The raw code to send, copy this from the dump output.
|
|
- **protocol** (*Optional*): The RC Switch protocol to use, see :ref:`remote_transmitter-rc_switch-protocol`
|
|
for more information.
|
|
- All other options from :ref:`remote_transmitter-transmit_action`.
|
|
|
|
.. _remote_transmitter-rc_switch-protocol:
|
|
|
|
RC Switch Protocol
|
|
^^^^^^^^^^^^^^^^^^
|
|
|
|
All RC Switch ``protocol`` settings have these settings:
|
|
|
|
- Either the value is an integer, then the inbuilt protocol definition with the given number
|
|
is used.
|
|
- Or a key-value mapping is given, then there are these settings:
|
|
|
|
- **pulse_length** (**Required**, int): The pulse length of the protocol - how many microseconds
|
|
one pulse should last for.
|
|
- **sync** (*Optional*): The number of high/low pulses for the sync header, defaults to ``[1, 31]``
|
|
- **zero** (*Optional*): The number of high/low pulses for a zero bit, defaults to ``[1, 3]``
|
|
- **one** (*Optional*): The number of high/low pulses for a one bit, defaults to ``[3, 1]``
|
|
- **inverted** (*Optional*, boolean): If this protocol is inverted. Defaults to ``false``.
|
|
|
|
``remote_transmitter.transmit_rc_switch_type_a`` Action
|
|
*******************************************************
|
|
|
|
This :ref:`action <config-action>` sends a type A RC-Switch code to a
|
|
remote transmitter.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
- remote_transmitter.transmit_rc_switch_type_a:
|
|
group: '01001'
|
|
device: '10110'
|
|
state: off
|
|
protocol: 1
|
|
|
|
Configuration variables:
|
|
|
|
- **group** (**Required**, string): The group to send the command to.
|
|
- **device** (**Required**, string): The device in the group to send the command to.
|
|
- **state** (**Required**, boolean): The on/off state to send.
|
|
- **protocol** (*Optional*): The RC Switch protocol to use, see :ref:`remote_transmitter-rc_switch-protocol`
|
|
for more information.
|
|
- All other options from :ref:`remote_transmitter-transmit_action`.
|
|
|
|
``remote_transmitter.transmit_rc_switch_type_b`` Action
|
|
*******************************************************
|
|
|
|
This :ref:`action <config-action>` sends a type B RC-Switch code to a
|
|
remote transmitter.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
- remote_transmitter.transmit_rc_switch_type_b:
|
|
address: '0100'
|
|
channel: '1011'
|
|
state: off
|
|
protocol: 1
|
|
|
|
Configuration variables:
|
|
|
|
- **address** (**Required**, int): The address to send the command to.
|
|
- **channel** (**Required**, int): The channel to send the command to.
|
|
- **state** (**Required**, boolean): The on/off state to send.
|
|
- **protocol** (*Optional*): The RC Switch protocol to use, see :ref:`remote_transmitter-rc_switch-protocol`
|
|
for more information.
|
|
- All other options from :ref:`remote_transmitter-transmit_action`.
|
|
|
|
``remote_transmitter.transmit_rc_switch_type_c`` Action
|
|
*******************************************************
|
|
|
|
This :ref:`action <config-action>` sends a type C RC-Switch code to a
|
|
remote transmitter.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
- remote_transmitter.transmit_rc_switch_type_c:
|
|
family: 'C'
|
|
group: 3
|
|
device: 1
|
|
state: off
|
|
protocol: 1
|
|
|
|
Configuration variables:
|
|
|
|
- **family** (**Required**, string): The family to send the command to. Range is ``a`` to ``p``.
|
|
- **group** (**Required**, int): The group to send the command to. Range is 1 to 4.
|
|
- **device** (**Required**, int): The device to send the command to. Range is 1 to 4.
|
|
- **state** (**Required**, boolean): The on/off state to send.
|
|
- **protocol** (*Optional*): The RC Switch protocol to use, see :ref:`remote_transmitter-rc_switch-protocol`
|
|
for more information.
|
|
- All other options from :ref:`remote_transmitter-transmit_action`.
|
|
|
|
``remote_transmitter.transmit_rc_switch_type_d`` Action
|
|
*******************************************************
|
|
|
|
This :ref:`action <config-action>` sends a type D RC-Switch code to a
|
|
remote transmitter.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
- remote_transmitter.transmit_rc_switch_type_d:
|
|
group: 'c'
|
|
device: 1
|
|
state: off
|
|
protocol: 1
|
|
|
|
Configuration variables:
|
|
|
|
- **group** (**Required**, int): The group to send the command to. Range is 1 to 4.
|
|
- **device** (**Required**, int): The device to send the command to. Range is 1 to 3.
|
|
- **state** (**Required**, boolean): The on/off state to send.
|
|
- **protocol** (*Optional*): The RC Switch protocol to use, see :ref:`remote_transmitter-rc_switch-protocol`
|
|
for more information.
|
|
- All other options from :ref:`remote_transmitter-transmit_action`.
|
|
|
|
.. _remote-setting-up-infrared:
|
|
|
|
Setting up Infrared Devices
|
|
---------------------------
|
|
|
|
In this guide an infrared device will be set up with ESPHome. First, the remote code
|
|
will be captured with an IR receiver module (like `this one <https://www.sparkfun.com/products/10266>`__).
|
|
We will use ESPHome's dumping ability to output the decoded remote code directly.
|
|
|
|
Then we will set up a new remote transmitter with an infrared LED (like
|
|
`this one <https://learn.sparkfun.com/tutorials/ir-communication/all>`__) to transmit the
|
|
code when a switch is triggered.
|
|
|
|
First, connect the infrared receiver module to a pin on your board and set up a
|
|
remote_receiver instance:
|
|
|
|
.. code-block:: yaml
|
|
|
|
remote_receiver:
|
|
pin: D0
|
|
dump: all
|
|
|
|
Compile and upload the code. While viewing the log output from the ESP,
|
|
press a button on an infrared remote you want to capture (one at a time).
|
|
|
|
You should see log output like below:
|
|
|
|
.. code-block:: text
|
|
|
|
# If the codec is known:
|
|
[D][remote.panasonic] Received Panasonic: address=0x4004 command=0x8140DFA2
|
|
|
|
# Or raw output if it's not known yet
|
|
# The values may fluctuate a bit, but as long as they're similar it's ok
|
|
[D][remote.raw] Received Raw: 4088, -1542, 1019, -510, 513, -1019, 510, -509, 511, -510, 1020,
|
|
[D][remote.raw] -1020, 1022, -1019, 510, -509, 511, -510, 511, -509, 511, -510,
|
|
[D][remote.raw] 1020, -1019, 510, -511, 1020, -510, 512, -508, 510, -1020, 1022
|
|
|
|
If the codec is already implemented in ESPHome, you will see the decoded value directly -
|
|
otherwise you will see the raw data dump (which you can use just as well). You have
|
|
just successfully captured your first infrared code.
|
|
|
|
Now let's use this information to emulate a button press from the ESP. First, wire up the
|
|
IR diode to a new pin on the ESP and configure a global ``remote_transmitter`` instance:
|
|
|
|
.. code-block:: yaml
|
|
|
|
remote_transmitter:
|
|
pin: D1
|
|
# Infrared remotes use a 50% carrier signal
|
|
carrier_duty_percent: 50%
|
|
|
|
This will allow us to send any data we want via the IR LED. To replicate the codes we decoded
|
|
earlier, create a new template switch that sends the infrared code when triggered:
|
|
|
|
.. code-block:: yaml
|
|
|
|
switch:
|
|
- platform: template
|
|
name: Panasonic Power Button
|
|
turn_on_action:
|
|
- remote_transmitter.transmit_panasonic:
|
|
address: 0x4004
|
|
command: 0x8140DFA2
|
|
|
|
# Or for raw code
|
|
switch:
|
|
- platform: template
|
|
name: Raw Code Power Button
|
|
turn_on_action:
|
|
- remote_transmitter.transmit_raw:
|
|
carrier_frequency: 38kHz
|
|
code: [4088, -1542, 1019, -510, 513, -1019, 510, -509, 511, -510, 1020,
|
|
-1020, 1022, -1019, 510, -509, 511, -510, 511, -509, 511, -510,
|
|
1020, -1019, 510, -511, 1020, -510, 512, -508, 510, -1020, 1022]
|
|
|
|
Recompile again, when you power up the device the next time you will see a new switch
|
|
in the frontend. Click on it and you should see the remote signal being transmitted. Done!
|
|
|
|
.. _remote-setting-up-rf:
|
|
|
|
Setting Up RF Devices
|
|
---------------------
|
|
|
|
The ``remote_transmitter`` and ``remote_receiver`` components can also be used to send
|
|
and receive 433MHz RF signals. This guide will discuss setting up a 433MHz receiver to
|
|
capture a device's remote codes. After that we will set up a 433MHz transmitter to replicate
|
|
the remote code with the press of a switch in the frontend.
|
|
|
|
First, connect the RF module to a pin on the ESP and set up a remote_receiver instance:
|
|
|
|
.. code-block:: yaml
|
|
|
|
remote_receiver:
|
|
pin: D0
|
|
dump: all
|
|
# Settings to optimize recognition of RF devices
|
|
tolerance: 50%
|
|
filter: 250us
|
|
idle: 4ms
|
|
buffer_size: 2kb
|
|
|
|
Compile and upload the code. While viewing the log output from the ESP,
|
|
press a button on an RF remote you want to capture (one at a time).
|
|
|
|
You should see log output like below:
|
|
|
|
.. code-block:: text
|
|
|
|
# If the codec is known:
|
|
[D][remote.rc_switch] Received RCSwitch: protocol=2 data='100010000000000010111110'
|
|
|
|
# Or raw output if it's not known yet
|
|
# The values may fluctuate a bit, but as long as they're similar it's ok
|
|
[D][remote.raw] Received Raw: 4088, -1542, 1019, -510, 513, -1019, 510, -509, 511, -510, 1020,
|
|
[D][remote.raw] -1020, 1022, -1019, 510, -509, 511, -510, 511, -509, 511, -510,
|
|
[D][remote.raw] 1020, -1019, 510, -511, 1020, -510, 512, -508, 510, -1020, 1022
|
|
|
|
.. note::
|
|
|
|
If the log output is flooded with "Received Raw" messages, you can also disable raw
|
|
remote code reporting and rely on rc_switch to decode the values.
|
|
|
|
.. code-block:: yaml
|
|
|
|
remote_receiver:
|
|
pin: D0
|
|
dump:
|
|
- rc_switch
|
|
tolerance: 50%
|
|
filter: 250us
|
|
idle: 4ms
|
|
buffer_size: 2kb
|
|
|
|
If the codec is already implemented in ESPHome, you will see the decoded value directly -
|
|
otherwise you will see the raw data dump (which you can use just as well). You have
|
|
just successfully captured your first RF code.
|
|
|
|
Now let's use this information to emulate a button press from the ESP. First, wire up the
|
|
RF transmitter to a new pin on the ESP and configure a global ``remote_transmitter`` instance:
|
|
|
|
.. code-block:: yaml
|
|
|
|
remote_transmitter:
|
|
pin: D1
|
|
# RF uses a 100% carrier signal
|
|
carrier_duty_percent: 100%
|
|
|
|
This will allow us to send any data we want via the RF transmitter. To replicate the codes we decoded
|
|
earlier, create a new template switch that sends the RF code when triggered:
|
|
|
|
.. code-block:: yaml
|
|
|
|
switch:
|
|
- platform: template
|
|
name: RF Power Button
|
|
turn_on_action:
|
|
- remote_transmitter.transmit_rc_switch_raw:
|
|
code: '100010000000000010111110'
|
|
protocol: 2
|
|
|
|
# Or for raw code
|
|
switch:
|
|
- platform: template
|
|
name: Raw Code Power Button
|
|
turn_on_action:
|
|
- remote_transmitter.transmit_raw:
|
|
code: [4088, -1542, 1019, -510, 513, -1019, 510, -509, 511, -510, 1020,
|
|
-1020, 1022, -1019, 510, -509, 511, -510, 511, -509, 511, -510,
|
|
1020, -1019, 510, -511, 1020, -510, 512, -508, 510, -1020, 1022]
|
|
|
|
Recompile again, when you power up the device the next time you will see a new switch
|
|
in the frontend. Click on it and you should see the remote signal being transmitted. Done!
|
|
|
|
See Also
|
|
--------
|
|
|
|
- :doc:`index`
|
|
- :doc:`/components/remote_receiver`
|
|
- `RCSwitch <https://github.com/sui77/rc-switch>`__ by `Suat Özgür <https://github.com/sui77>`__
|
|
- `IRRemoteESP8266 <https://github.com/markszabo/IRremoteESP8266/>`__ by `Mark Szabo-Simon <https://github.com/markszabo>`__
|
|
- :apiref:`remote_transmitter/remote_transmitter.h`
|
|
- :ghedit:`Edit`
|