mirror of
https://github.com/esphome/esphome-docs.git
synced 2024-12-26 17:27:47 +01:00
126 lines
3.9 KiB
ReStructuredText
126 lines
3.9 KiB
ReStructuredText
FTLab GDK101 Gamma Radiation Sensor Module
|
|
==========================================
|
|
|
|
.. seo::
|
|
:description: Instructions for setting up GDK101 Gamma Radiation Sensor Module
|
|
:image: gdk101.jpg
|
|
:keywords: gdk101
|
|
|
|
The **GDK101** sensor platform allows you to use your GDK101 sensor to monitor radiation levels at your place.
|
|
|
|
The GDK101 can measure average dose rate per 1 and 10 minutes, it also detect vibrations that can disturb the measurement.
|
|
|
|
The GDK101 requires setting up :ref:`I²C <i2c>` for data communication.
|
|
|
|
Module Pins
|
|
-----------
|
|
|
|
============ ===============================================================
|
|
Module Pin Description
|
|
============ ===============================================================
|
|
TX UART TX pin
|
|
RX UART RX pin
|
|
+5VIN Positive supply voltage
|
|
GND1 Ground
|
|
SDA I²C data bus
|
|
SCL I²C clock bus
|
|
|
|
A0 Adress Jumper 1
|
|
A1 Adress Jumper 2
|
|
============ ===============================================================
|
|
|
|
============ ===============================================================
|
|
I2C Address Jumpers State
|
|
============ ===============================================================
|
|
0x18 A0 Short, A1 Short
|
|
0x19 A0 Open, A1 Short
|
|
0x1A A0 Short, A1 Open
|
|
0x1B A0 Open, A1 Open
|
|
============ ===============================================================
|
|
|
|
.. figure:: images/gdk101.jpg
|
|
:align: center
|
|
:width: 50.0%
|
|
|
|
GDK101 Gamma Radiation Sensor Module.
|
|
|
|
Component/Hub
|
|
-------------
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Example configuration entry
|
|
gdk101:
|
|
i2c_id: bus_a
|
|
address: 0x18
|
|
update_interval: 10s
|
|
|
|
- **address** (*Optional*, int): Manually specify the I²C address of
|
|
the sensor. Defaults to ``0x18`` (``A0`` and ``A1`` shorted).
|
|
The address is made up using the state of ``A0`` as bit 1 and the state of ``A1`` as bit 2, so a total of four addresses is possible.
|
|
- **update_interval** (*Optional*, int): Manually defined update iterval of sensor. Default to 60s.
|
|
- **i2c_id** (*Optional*, string): Optional name of the bus.
|
|
|
|
Sensor
|
|
------
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Example configuration entry
|
|
sensor:
|
|
- platform: gdk101
|
|
radiation_dose_per_1m:
|
|
name: "GDK101 Radiation Dose @ 1 min"
|
|
radiation_dose_per_10m:
|
|
name: "GDK101 Radiation Dose @ 10 min"
|
|
status:
|
|
name: "GDK101 Status"
|
|
version:
|
|
name: "GDK101 FW Version"
|
|
measurement_duration:
|
|
name: "GDK101 Measuring Time"
|
|
|
|
A sensor platform to radiation data
|
|
|
|
Configuration variables:
|
|
|
|
- **radiation_dose_per_1m** (**Required**): Radiation average dose per 1 minute.
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
- **radiation_dose_per_10m** (**Required**): Radiation average dose per 10 minutes.
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
- **version** (**Required**): Fimware version of the module.
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
- **status** (*Optional*): Sensor status.
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
- **measurement_duration** (*Optional*): Total time of measurement.
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
|
|
Binary Sensor
|
|
-------------
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Example configuration entry
|
|
binary_sensor:
|
|
- platform: gdk101
|
|
vibrations:
|
|
name: "GDK101 Vibrations"
|
|
|
|
Binary sensor that indicates if measurement was disturbed by vibrations.
|
|
|
|
Configuration variables:
|
|
|
|
- **vibrations** (**Required**): Vibration status.
|
|
All options from :ref:`Binary Sensor <config-binary_sensor>`.
|
|
|
|
|
|
See Also
|
|
--------
|
|
|
|
- :ref:`sensor-filters`
|
|
- :apiref:`gdk101/gdk101.h`
|
|
- `Data Sheet <https://www.eleparts.co.kr/data/goods_old/design/product_file/Hoon/AN_GDK101_V1.0_I2C.pdf>`__
|
|
- `Application Notes <https://merona.blob.core.windows.net/radonftlab-web/GDK101.zip>`__
|
|
- `Arduino Sensors for Everyone blog post <https://arduino.steamedu123.com/entry/GDK101-Radiation-Sensor>`__
|
|
- :ghedit:`Edit`
|