esphome-docs/components/rf_bridge.rst
2024-08-06 05:10:01 +00:00

413 lines
12 KiB
ReStructuredText

RF Bridge Component
===================
.. seo::
:description: Instructions for setting up the RF Bridge in ESPHome.
:image: rf_bridge.jpg
:keywords: RF Bridge
The ``RF Bridge`` Component provides the ability to send and receive 433MHz remote codes using the
embedded EFM8BB1 microcontroller. This component implements the communication protocol
that the original ``efm8bb1`` firmware implements. The device is connected via the
:doc:`UART bus </components/uart>`. The uart bus must be configured at the same speed of the module
which is 19200bps.
.. warning::
If you are using the :doc:`logger` make sure you disable the uart logging with the
``baud_rate: 0`` option.
.. figure:: images/rf_bridge-full.jpg
:align: center
:width: 60.0%
Sonoff RF Bridge 433, version R1 or R2 V1.0
.. code-block:: yaml
# Example configuration entry
uart:
baud_rate: 19200
rf_bridge:
on_code_received:
- homeassistant.event:
event: esphome.rf_code_received
data:
sync: !lambda 'return format_hex(data.sync);'
low: !lambda 'return format_hex(data.low);'
high: !lambda 'return format_hex(data.high);'
code: !lambda 'return format_hex(data.code);'
Configuration variables:
------------------------
- **uart_id** (*Optional*, :ref:`config-id`): Manually specify the ID of the UART hub.
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID used for code generation.
- **on_code_received** (*Optional*, :ref:`Automation <automation>`): An action to be
performed when a code is received. See :ref:`rf_bridge-on_code_received`.
.. _rf_bridge-on_code_received:
``on_code_received`` Trigger
----------------------------
With this configuration option you can write complex automations whenever a code is
received. To use the code, use a :ref:`lambda <config-lambda>` template, the code
and the corresponding protocol timings are available inside that lambda under the
variables named ``code``, ``sync``, ``high`` and ``low``.
.. code-block:: yaml
on_code_received:
- homeassistant.event:
event: esphome.rf_code_received
data:
sync: !lambda 'return format_hex(data.sync);'
low: !lambda 'return format_hex(data.low);'
high: !lambda 'return format_hex(data.high);'
code: !lambda 'return format_hex(data.code);'
.. _rf_bridge-send_code_action:
``rf_bridge.send_code`` Action
------------------------------
Send an RF code using this action in automations.
.. code-block:: yaml
on_...:
then:
- rf_bridge.send_code:
sync: 0x700
low: 0x800
high: 0x1000
code: 0xABC123
Configuration options:
- **sync** (**Required**, int, :ref:`templatable <config-templatable>`): RF Sync timing
- **low** (**Required**, int, :ref:`templatable <config-templatable>`): RF Low timing
- **high** (**Required**, int, :ref:`templatable <config-templatable>`): RF high timing
- **code** (**Required**, int, :ref:`templatable <config-templatable>`): RF code
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID of the RF Bridge if you have multiple components.
.. note::
This action can also be written in :ref:`lambdas <config-lambda>`:
.. code-block:: cpp
id(rf_bridge).send_code(0x700, 0x800, 0x1000, 0xABC123);
.. _rf_bridge-send_raw_action:
``rf_bridge.send_raw`` Action
-----------------------------
Send a raw command to the onboard EFM8BB1 chip.
You can see a list of available commands and format in the `Portisch Wiki <https://github.com/Portisch/RF-Bridge-EFM8BB1/wiki/Commands>`__
This can be used to send raw RF codes in automation's, mainly for protocols that are not supported.
If you have *Portisch* firmware installed, these raw codes can be obtained with the help of :ref:`rf_bridge-start_bucket_sniffing_action`
.. code-block:: yaml
on_...:
then:
- rf_bridge.send_raw:
raw: AAA5070008001000ABC12355
Configuration options:
- **raw** (**Required**, string, :ref:`templatable <config-templatable>`): RF raw string
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID of the RF Bridge if you have multiple components.
.. note::
This action can also be written in :ref:`lambdas <config-lambda>`:
.. code-block:: cpp
id(rf_bridge).send_raw("AAA5070008001000ABC12355");
.. _rf_bridge-learn_action:
``rf_bridge.learn`` Action
--------------------------
Tell the RF Bridge to learn new protocol timings using this action in automations.
A new code with timings will be returned to :ref:`rf_bridge-on_code_received`
.. code-block:: yaml
on_...:
then:
- rf_bridge.learn
Configuration options:
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID of the RF Bridge if you have multiple components.
.. note::
This action can also be written in :ref:`lambdas <config-lambda>`:
.. code-block:: cpp
id(rf_bridge).learn();
Portisch firmware
-----------------
If you have flashed the secondary MCU with the `Portisch firmware <https://github.com/Portisch/RF-Bridge-EFM8BB1>`__,
ESPHome is able to receive the extra protocols that can be decoded as well as activate the other modes supported.
.. _rf_bridge-on_advanced_code_received:
``on_advanced_code_received`` Trigger
*************************************
Similar to :ref:`rf_bridge-on_code_received`, this trigger receives the codes after advanced sniffing is started.
To use the code, use a :ref:`lambda <config-lambda>` template, the code and the corresponding protocol and length
are available inside that lambda under the variables named ``code``, ``protocol`` and ``length``.
.. code-block:: yaml
on_advanced_code_received:
- homeassistant.event:
event: esphome.rf_advanced_code_received
data:
length: !lambda 'return format_hex(data.length);'
protocol: !lambda 'return format_hex(data.protocol);'
code: !lambda 'return data.code;'
.. _rf_bridge-send_advanced_code_action:
``rf_bridge.send_advanced_code`` Action
***************************************
Send an RF code using this action in automations.
.. code-block:: yaml
on_...:
then:
- rf_bridge.send_advanced_code:
length: 0x04
protocol: 0x01
code: "ABC123"
Configuration options:
- **length** (**Required**, int, :ref:`templatable <config-templatable>`): Length of code plus protocol
- **protocol** (**Required**, int, :ref:`templatable <config-templatable>`): RF Protocol
- **code** (**Required**, string, :ref:`templatable <config-templatable>`): RF code
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID of the RF Bridge if you have multiple components.
.. note::
This action can also be written in :ref:`lambdas <config-lambda>`:
.. code-block:: cpp
id(rf_bridge).send_advanced_code(0x04, 0x01, "ABC123");
.. _rf_bridge-start_advanced_sniffing_action:
``rf_bridge.start_advanced_sniffing`` Action
********************************************
Tell the RF Bridge to listen for the advanced/extra protocols defined in the portisch firmware.
The decoded codes with length and protocol will be returned to :ref:`rf_bridge-on_advanced_code_received`
.. code-block:: yaml
on_...:
then:
- rf_bridge.start_advanced_sniffing
Configuration options:
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID of the RF Bridge if you have multiple components.
.. note::
This action can also be written in :ref:`lambdas <config-lambda>`:
.. code-block:: cpp
id(rf_bridge).start_advanced_sniffing();
.. _rf_bridge-stop_advanced_sniffing_action:
``rf_bridge.stop_advanced_sniffing`` Action
*******************************************
Tell the RF Bridge to stop listening for the advanced/extra protocols defined in the portisch firmware.
.. code-block:: yaml
on_...:
then:
- rf_bridge.stop_advanced_sniffing
Configuration options:
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID of the RF Bridge if you have multiple components.
.. note::
This action can also be written in :ref:`lambdas <config-lambda>`:
.. code-block:: cpp
id(rf_bridge).stop_advanced_sniffing();
.. _rf_bridge-start_bucket_sniffing_action:
``rf_bridge.start_bucket_sniffing`` Action
******************************************
Tell the RF Bridge to dump raw sniffing data. Useful for getting codes for unsupported protocols.
The raw data will be available in the log and can later be used with :ref:`rf_bridge-send_raw_action` action.
.. note::
A conversion from *B1* (received) raw format to *B0* (send) raw command format should be applied.
For this, you can use the tool `BitBucket Converter <https://bbconv.hrbl.pl/>`__
.. note::
There seems to be an overflow problem in Portisch firmware and after a short while, the bucket sniffing stops.
You should re-call the action to reset and start sniffing again.
.. code-block:: yaml
on_...:
then:
- rf_bridge.start_bucket_sniffing
Configuration options:
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID of the RF Bridge if you have multiple components.
.. note::
This action can also be written in :ref:`lambdas <config-lambda>`:
.. code-block:: cpp
id(rf_bridge).start_bucket_sniffing();
.. _rf_bridge-beep_action:
``rf_bridge.beep`` Action
*************************
Activate the internal buzzer to make a beep.
.. code-block:: yaml
on_...:
then:
- rf_bridge.beep:
duration: 100
Configuration options:
- **duration** (**Required**, string, :ref:`templatable <config-templatable>`): beep duration in milliseconds.
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID of the RF Bridge if you have multiple components.
.. note::
This action can also be written in :ref:`lambdas <config-lambda>`:
.. code-block:: cpp
id(rf_bridge).beep(100);
Getting started with Home Assistant
-----------------------------------
The following code will get you up and running with a configuration sending codes to
Home Assistant as events and will also setup a service so you can send codes with your RF Bridge.
.. code-block:: yaml
api:
actions:
- action: send_rf_code
variables:
sync: int
low: int
high: int
code: int
then:
- rf_bridge.send_code:
sync: !lambda 'return sync;'
low: !lambda 'return low;'
high: !lambda 'return high;'
code: !lambda 'return code;'
- action: learn
then:
- rf_bridge.learn
uart:
tx_pin: 1
rx_pin: 3
baud_rate: 19200
logger:
baud_rate: 0
rf_bridge:
on_code_received:
then:
- homeassistant.event:
event: esphome.rf_code_received
data:
sync: !lambda 'return format_hex(data.sync);'
low: !lambda 'return format_hex(data.low);'
high: !lambda 'return format_hex(data.high);'
code: !lambda 'return format_hex(data.code);'
Now your latest received code will be in an event.
To trigger the automation from Home Assistant you can invoke the service with this code:
.. code-block:: yaml
automation:
# ...
action:
- action: esphome.rf_bridge_send_rf_code
data:
sync: 0x700
low: 0x800
high: 0x1000
code: 0xABC123
See Also
--------
- :apiref:`rf_bridge/rf_bridge.h`
- :ref:`lambda_magic_rf_queues`
- `RF-Bridge-EFM8BB1 <https://github.com/Portisch/RF-Bridge-EFM8BB1>`__ by `Portisch <https://github.com/Portisch>`__
- :doc:`/components/uart`
- :doc:`/components/remote_receiver`
- :doc:`/components/remote_transmitter`
- :ghedit:`Edit`