esphome-docs/devices/nodemcu_esp8266.rst
Otto Winter 8d9b0d2375
Netlify (#153)
* Netlify

* Fix

* Faster doxygen

* Update Makefile

* Try without api

* Debug

* Fix

* Update Makefile

* Debug

* Try 1.8.13

* Remove debug

* Update Makefile

* Optimize
2019-02-07 13:54:45 +01:00

79 lines
2.9 KiB
ReStructuredText

NodeMCU ESP8266
===============
.. seo::
:description: Instructions for using nodemcu ESP8266 boards in esphomelib together with a description of their pins and uses.
:image: nodemcu_esp8266.jpg
:keywords: NodeMCU, ESP8266
The NodeMCU board is fully supported by esphomeyaml. Simply select ``ESP8266`` when
the esphomeyaml wizard asks you for your platform and |nodemcuv2|_ as the board type.
.. note::
Most NodeMCU that can be purchased now are version 2 or upwards, if you're using an
original v1 board, set the board type to |nodemcu|_.
.. |nodemcuv2| replace:: ``nodemcuv2``
.. _nodemcuv2: http://docs.platformio.org/en/latest/platforms/espressif8266.html#nodemcu
.. |nodemcu| replace:: ``nodemcu``
.. _nodemcu: http://docs.platformio.org/en/latest/platforms/espressif8266.html#nodemcu
.. code-block:: yaml
# Example configuration entry
esphomeyaml:
name: livingroom
platform: ESP8266
board: nodemcuv2
The NodeMCU's pin numbering as seen on the board (the ``D0`` etc pins) is different from
the internal pin numbering. For example, the ``D8`` pin number maps to the internal
``GPIO0`` pin. Fortunately esphomeyaml knows the mapping from the on-board pin numbers
to the internal pin numbering, but you need to prefix the pin numbers with ``D`` as in below
image in order for this automatic mapping to occur.
In general, it is best to just use the ``D0``, ``D1``, ... pin numbering to avoid confusion
.. figure:: images/nodemcu_esp8266-full.jpg
:align: center
Pins on the NodeMCU ESP8266 development board.
Note that in certain conditions you *can* use the pins marked as ``INTERNAL`` in above image.
- ``D0`` also can be used to wake the device up from :doc:`deep sleep </components/deep_sleep>` if
the pin is connected to the ``RESET`` pin. ``D0`` is additionally connected to the LED
next to the UART chip, but in an inverted mode.
- ``D3``, ``D4`` and ``D8`` are used on startup to determine the boot mode, therefore these pins should
not be pulled low on startup. You can, however, still use them as output pins.
- ``A0``: This pin can be used as a normal GPIO pin (like ``D1`` etc) but additionally can measure
voltages from 0 to 1.0V using the :doc:`/components/sensor/adc`.
- ``VIN``: This pin can be used to use an external power supply with the board. Supply a voltage from
3.3V to 12V to this pin and the linear voltage regulator on the board will power the board.
- ``ENABLE``/``RESET``: When these pins are triggered, the board resets. The difference between the pins
is how they can handle voltages above 3.3V
.. code-block:: yaml
# Example configuration entry
esphomeyaml:
name: livingroom
platform: ESP8266
board: nodemcuv2
binary_sensor:
- platform: gpio
name: "Pin D0"
pin: D0
See Also
--------
- :doc:`esp8266`
- :doc:`nodemcu_esp32`
- :ghedit:`Edit`
.. disqus::