Upstream/esphome-docs
1
0
Fork 0
mirror of https://github.com/esphome/esphome-docs.git synced 2024-11-05 09:20:08 +01:00
Code Issues Projects Releases Wiki Activity
32740a2fa8
esphome-docs/cookbook/brilliant-mirabella-genio-smart-plugs.rst
Jesse Hills 1f8ecd46a6
Convert pin mode examples to new format (#1591)
2021-11-03 19:55:26 +01:00

546 lines
16 KiB
ReStructuredText
Raw Blame History

Brilliant / Mirabella Genio Smart Plugs
=======================================
Brilliant / Mirabella Genio Smart Plugs are a Tuya-based smart plugs sold by Bunnings and Kmart respectively in Australia.
.. figure:: images/brilliant-mirabella-genio-smart-plugs.jpg
:align: center
:width: 50.0%
Originally intended to be used with their companion apps once flashed using `tuya-convert <https://github.com/ct-Open-Source/tuya-convert>`__ ESPHome generated
firmware can be uploaded allowing you to control the smart plugs via Home Assistant.
1. Create the ESPHome Firmware
------------------------------
#. Refer to either :doc:`/guides/getting_started_command_line` or :doc:`/guides/getting_started_hassio` before moving onto the next step.
#. Select a plug configuration below based on the plug/s you have and copy all of the text in the code block and paste into your
``name_of_esphome_configuration.yaml`` file.
#. Compile the firmware, again depending on your chosen setup refer to the guides in the first point.
2. Flashing
-----------
2.1 Prerequisites
*****************
#. Before you begin you'll need one of the following Linux machines running the latest copy of `Raspbian Stretch Lite
<https://www.raspberrypi.org/downloads/raspbian/>`__
a. Raspberry Pi 2B/B+ with `USB WiFi Dongle <https://www.raspberrypi.org/products/raspberry-pi-usb-wifi-dongle/>`__.
b. Raspberry Pi 3B/B+.
.. note::
As per the `tuya-convert documentation <https://github.com/ct-Open-Source/tuya-convert/blob/master/README.md#requirements>`__:
Any Linux with a Wifi adapter which can act as an Access Point should also work. Please note that we have tested the Raspberry Pi with clean installations
only. If you use your Raspberry Pi for anything else, we recommend using another SD card with a clean installation.
#. A microSD card (minimum 2GB, 8GB+ recommended).
#. Any WiFi device which can connect to the SSID generated by the Raspberry Pi and eventually the flashed Tuya device. **This cannot be an iOS / Apple device.
Android devices will work.**
2.2 Installing the OS
*********************
#. It's recommended to read the documentation provided by the Raspberry Pi Foundation on the best way to flash the OS to the microSD card depending on your
platform - `Installing operating system images <https://www.raspberrypi.org/documentation/installation/installing-images/>`__.
#. After you've flashed the microSD card browse to the "boot" partition and add a blank file called "ssh" **(without any extension)** which will enable the
SSH server upon first boot, extended information on this step can be found `here
<https://www.raspberrypi.org/documentation/remote-access/ssh/README.md#3-enable-ssh-on-a-headless-raspberry-pi-add-file-to-sd-card-on-another-machine>`__.
#. Plug the microSD card into the Raspberry Pi, connect network cable and power, the Raspberry Pi will start to boot.
2.3 Connecting to the Pi via SSH
********************************
#. Download and install `Putty <https://www.chiark.greenend.org.uk/~sgtatham/putty/latest.html>`__.
#. Open Putty.
#. Enter the IP of Raspberry Pi in the box that says "Host Name", leaving the port set to 22 (default for SSH). A list of recommended ways can be found `here
<https://www.raspberrypi.org/documentation/remote-access/ip-address.md>`__, but the easiest is to download and use `Fing <https://www.fing.com/>`__
(`Android <https://play.google.com/store/apps/details?id=com.overlook.android.fing&hl=en_GB>`__ / `iOS
<https://itunes.apple.com/us/app/fing-network-scanner/id430921107?mt=8>`__).
#. In the "Saved Sessions" input box, name the Raspberry Pi connection and then press "Save".
#. Select your new saved session from the list.
#. Press "Open".
2.4 Configuring the Pi
**********************
#. In the putty window login with the **pi** as the user and **raspberry** for the password.
#. Type ``sudo apt-get update && sudo apt-get dist-upgrade -y`` and wait for the upgrades to install.
#. Type ``sudo apt-get install git`` and wait for it to install.
2.5 Setup and Install tuya-convert
**********************************
#. In the putty window type ``git clone https://github.com/ct-Open-Source/tuya-convert`` press enter and wait while the repository is cloned.
#. Type ``cd tuya-convert`` and press enter.
#. Type ``./install_prereq.sh`` press enter and wait as the script gathers all the required components needed to function.
2.6 Upload ESPHome Firmware using SFTP
**************************************
#. Download `FileZilla <https://filezilla-project.org/download.php?type=client>`__ or `WinSCP <https://winscp.net/eng/index.php>`__ or use your preferred FTP
client.
#. Depending on the program you need to connect to the Pi using the IP address as the hostname and the username and password the same as you used to connect
via SSH and ensure your connection type is set to **SFTP**
#. Browse to ``/root/tuya-convert/files``.
#. Upload your compiled ``firmware.bin`` file to this directory. For command line based installs you can access the file under
``<CONFIG_DIR>/<NODE_NAME>/.pioenvs/<NODE_NAME>/firmware.bin`` alternatively Home Assistant add-on users can download the file directly from the web ui.
2.7 Use tuya-convert to install ESPHome Firmware
************************************************
#. Type ``./start_flash.sh``
#. Type ``yes`` to accept the warning.
#. Connect your alternative WiFi device (non iOS / Apple based) to the ``vtrust-flash`` SSID using ``flashmeifyoucan`` as the password. This is the network
being broadcast by the Pi from the tuya flash script.
#. If you haven't already connect your smart plug and turn it on. It should automatically enter pairing mode, if it doesn't follow the instructions below:
* Brilliant `(PDF Manual) <https://www.brilliantsmart.com.au/wp-content/uploads/2019/02/03.-How-to-setup-the-Smart-plug.pdf>`__
* To connect the Smart WiFi Plug to your WiFi press and hold the manual control button for about 5 seconds until you hear a click. Let go of the button
as soon as you hear the **click**. Then press button once again to activate blinking. **The red indicator light should now blink rapidly (2 times per
second)**.
* Mirabella `(PDF Manual) <https://img1.wsimg.com/blobby/go/67cdd3b9-3600-4104-b097-603c05201237/downloads/1cq5h6nt7_336441.pdf>`__
* To do this, ensure your plug is on (the indicator light should be blue), hold the power button down for 5 seconds until you hear a click, let go of the
power button and then press the button once to activate.
#. Press enter on your putty window to start the flash process and wait. If the connection is successful you should see a large amount of scrolling text, this
is the script backing up the factory shipped firmware.
#. Once the process is complete you can type ``curl http://10.42.42.42/flashURL?url=http://10.42.42.1/files/firmware.bin``
#. The plug will restart and if everything is working correctly after a few seconds you should be able to press the button triggering the relay and turning the
blue led on.
3. Smart Plug Configurations
----------------------------
Thanks to the existing work by `@ideasman69 <https://github.com/ct-Open-Source/tuya-convert/issues/66>`__ and
`afalzon <https://github.com/arendst/Sonoff-Tasmota/wiki/Mirabella-Genio-Smart-Plug>`__
which these adaptions created by `@cryptelli <https://community.home-assistant.io/u/cryptelli>`__ are based on.
3.1 Brilliant Smart Plug
************************
.. code-block:: yaml
esphome:
name: brilliant_smart_plug
platform: ESP8266
board: esp01_1m
wifi:
ssid: 'WIFI'
password: 'WIFIPASS'
logger:
api:
ota:
binary_sensor:
- platform: gpio
pin:
number: 14
mode:
input: true
pullup: true
inverted: true
name: "Power Button"
on_press:
- switch.toggle: relay
- platform: status
name: "Status"
switch:
- platform: gpio
id: red_led
pin:
number: GPIO12
inverted: true
- platform: gpio
name: "Brilliant Smart Plug"
pin: GPIO5
id: relay
# Turn off red LED to show blue when turned on
on_turn_on:
- switch.turn_off: red_led
# Turns on the red LED once the plug is turned off. Stock plug doesn't do this, to restore normal behavior remove the on_turn_on and on_turn_off
# blocks.
on_turn_off:
- switch.turn_on: red_led
3.2 Mirabella Genio Wi-Fi 1 USB Adaptor
***************************************
.. code-block:: yaml
esphome:
name: mirabella_genio_smart_plug
platform: ESP8266
board: esp01_1m
wifi:
ssid: 'WIFI'
password: 'WIFIPASS'
logger:
api:
ota:
binary_sensor:
- platform: gpio
pin:
number: GPIO13
mode:
input: true
pullup: true
inverted: true
name: "Power Button"
on_press:
- switch.toggle: relay
- platform: status
name: Status
switch:
- platform: gpio
id: red_led
pin:
number: GPIO4
inverted: true
- platform: gpio
name: "Mirabella Genio Smart Plug"
pin: GPIO12
id: relay
# Turn on red LED
on_turn_on:
- switch.turn_on: red_led
# Turns off red LED
on_turn_off:
- switch.turn_off: red_led
3.3 Gosund SP1
**************
.. code-block:: yaml
esphome:
name: gosund_sp1_smart_plug
platform: ESP8266
board: esp8285
wifi:
ssid: 'WIFI'
password: 'WIFIPASS'
logger:
api:
ota:
binary_sensor:
- platform: gpio
pin:
number: GPIO3
inverted: true
name: "Power Button"
on_press:
- switch.toggle: relay
switch:
- platform: gpio
id: led
pin: GPIO1
- platform: gpio
name: "Gosund SP1 Smart Plug"
pin: GPIO14
id: relay
on_turn_on:
- switch.turn_on: led
on_turn_off:
- switch.turn_off: led
sensor:
- platform: hlw8012
sel_pin:
number: GPIO12
inverted: true
cf_pin: GPIO04
cf1_pin: GPIO05
current_resistor: 0.00221
voltage_divider: 871
current:
name: "Gosund SP1 Smart Plug current"
unit_of_measurement: A
voltage:
name: "Gosund SP1 Smart Plug Voltage"
unit_of_measurement: V
power:
name: "Gosund SP1 Smart Plug Wattage"
unit_of_measurement: W
id: "energy_temp_Wattage"
change_mode_every: 8
update_interval: 10s
Check the following page for calibrating the measurements: :ref:`sensor-filter-calibrate_linear`.
3.4 Topersun WL-SC01 Smart Plug
*******************************
.. code-block:: yaml
esphome:
name: topersun_smart_plug
platform: ESP8266
board: esp01_1m
wifi:
ssid: 'WIFI'
password: 'WIFIPASS'
logger:
api:
ota:
binary_sensor:
- platform: gpio
pin:
number: 14
mode:
input: true
pullup: true
inverted: true
name: "Power Button"
on_press:
- switch.toggle: relay
- platform: status
name: "Status"
switch:
- platform: gpio
id: green_led
pin:
number: GPIO4
inverted: true
- platform: gpio
name: "Brilliant Smart Plug"
pin: GPIO12
id: relay
# Turn off green LED to show red when turned on.
on_turn_on:
- switch.turn_off: green_led
# Turns on the green LED once the plug is turned off.
on_turn_off:
- switch.turn_on: green_led
3.5 NEO Coolcam wifi smart plug
*******************************
.. code-block:: yaml
substitutions:
plug_name: coolcam_plug1
# Higher value gives lower watt readout
current_res: "0.00221"
# Lower value gives lower voltage readout
voltage_div: "800"
esphome:
name: ${plug_name}
platform: ESP8266
board: esp8285
wifi:
ssid: 'WIFI'
password: 'WIFIPASS'
logger:
api:
ota:
binary_sensor:
- platform: gpio
pin:
number: GPIO0
inverted: true
name: "${plug_name}_button"
on_press:
- switch.toggle: relay
switch:
- platform: gpio
name: "${plug_name}_LED_Red"
pin: GPIO13
inverted: true
restore_mode: ALWAYS_OFF
id: red_led
- platform: gpio
name: "${plug_name}_Relay"
pin: GPIO14
restore_mode: ALWAYS_ON
id: relay
on_turn_on:
- switch.turn_on: red_led
on_turn_off:
- switch.turn_off: red_led
sensor:
- platform: hlw8012
sel_pin:
number: GPIO12
inverted: true
cf_pin: GPIO04
cf1_pin: GPIO05
current_resistor: ${current_res}
voltage_divider: ${voltage_div}
current:
name: "${plug_name}_Amperage"
unit_of_measurement: A
voltage:
name: "${plug_name}_Voltage"
unit_of_measurement: V
power:
name: "${plug_name}_Wattage"
unit_of_measurement: W
id: "${plug_name}_Wattage"
change_mode_every: 8
update_interval: 10s
- platform: total_daily_energy
name: "${plug_name}_Total Daily Energy"
power_id: "${plug_name}_Wattage"
filters:
# Multiplication factor from W to kW is 0.001
- multiply: 0.001
unit_of_measurement: kWh
# Extra sensor to keep track of plug uptime
- platform: uptime
name: ${plug_name}_Uptime SensorPreformatted text
3.6 Arlec Grid Connect Smart Plug In Socket With 2.1A USB Charger
*****************************************************************
.. code-block:: yaml
substitutions:
item_name: "arlec_pc389ha_001"
esphome:
name: ${item_name}
platform: ESP8266
board: esp01_1m
wifi:
ssid: 'WIFI'
password: 'WIFIPASS'
# Enable fallback hotspot (captive portal) in case wifi connection fails
ap:
ssid: ${item_name}
captive_portal:
# Enable logging
logger:
# Enable Home Assistant API
api:
ota:
binary_sensor:
- platform: gpio
pin:
number: 14
mode:
input: true
pullup: true
inverted: true
name: "${item_name}_button"
on_press:
- switch.toggle: relay
- platform: status
name: "${item_name}_status"
switch:
- platform: gpio
id: blue_led
pin:
number: GPIO4
inverted: true
- platform: gpio
id: red_led
pin:
number: GPIO13
inverted: true
- platform: gpio
name: "${item_name}_power"
pin: GPIO12
id: relay
on_turn_on:
# Turn off blue LED to show blue when turned on
- switch.turn_off: red_led
- switch.turn_on: blue_led
on_turn_off:
# Turns on the blue LED once the plug is turned off
- switch.turn_off: blue_led
- switch.turn_on: red_led
sensor:
- platform: wifi_signal
name: "${item_name}_wifi_signal"
update_interval: 60s
4. Adding to Home Assistant
---------------------------
You can now add your smart plug to home assistant via the configurations page, look for 'ESPHome' under the Integrations option and click 'Configure'.
.. figure:: images/brilliant-mirabella-genio-smart-plugs-homeassistant.jpg
:align: center
:width: 50.0%
See Also
--------
- :doc:`/components/switch/index`
- :doc:`/components/binary_sensor/index`
- :doc:`/components/light/index`
- :doc:`/components/light/monochromatic`
- :doc:`/components/output/index`
- :doc:`/components/output/esp8266_pwm`
- :doc:`/guides/automations`
- :ghedit:`Edit`
Reference in New Issue View Git Blame Copy Permalink