mirror of
https://github.com/esphome/esphome-docs.git
synced 2024-11-05 09:20:08 +01:00
6ba7556bb9
makes it clearer when that component can be used !
157 lines
4.8 KiB
ReStructuredText
157 lines
4.8 KiB
ReStructuredText
Ethernet Component
|
||
==================
|
||
|
||
.. seo::
|
||
:description: Instructions for setting up the Ethernet configuration for your ESP32 node in ESPHome.
|
||
:image: ethernet.svg
|
||
:keywords: Ethernet, ESP32
|
||
|
||
This core ESPHome component sets up ethernet connections for ESP32s.
|
||
Ethernet for ESP8266 is not supported.
|
||
This component can't be used in same time than Wifi one, even if your ESP32 has both wired.
|
||
|
||
.. code-block:: yaml
|
||
|
||
# Example configuration entry
|
||
ethernet:
|
||
type: LAN8720
|
||
mdc_pin: GPIO23
|
||
mdio_pin: GPIO18
|
||
clk_mode: GPIO0_IN
|
||
phy_addr: 0
|
||
|
||
# Optional manual IP
|
||
manual_ip:
|
||
static_ip: 10.0.0.42
|
||
gateway: 10.0.0.1
|
||
subnet: 255.255.255.0
|
||
|
||
Configuration variables:
|
||
------------------------
|
||
|
||
- **type** (**Required**, string): The type of LAN chipset. Must be one of
|
||
``LAN8720`` or ``TLK110`` (see datasheet for more details).
|
||
- **mdc_pin** (**Required**, :ref:`config-pin`): The MDC pin of the board.
|
||
Usually this is ``GPIO23``.
|
||
- **mdio_pin** (**Required**, :ref:`config-pin`): The MDIO pin of the board.
|
||
Usually this is ``GPIO18``.
|
||
- **clk_mode** (*Optional*, string): The clock mode of the data lines, this must be one
|
||
of these values: (see datasheet of your board for more details)
|
||
|
||
- ``GPIO0_IN`` (Default) - External clock
|
||
- ``GPIO0_OUT`` - Internal clock
|
||
- ``GPIO16_OUT`` - Internal clock
|
||
- ``GPIO17_OUT`` - Internal clock
|
||
|
||
- **phy_addr** (*Optional*, int): The PHY addr type of the ethernet controller. Defaults to 0.
|
||
- **power_pin** (*Optional*, :ref:`Pin Schema <config-pin_schema>`): The pin with which
|
||
to control the power of the board. Leave unspecified for no power pin (default)
|
||
|
||
- **manual_ip** (*Optional*): Manually configure the static IP of the node.
|
||
|
||
- **static_ip** (**Required**, IPv4 address): The static IP of your node.
|
||
- **gateway** (**Required**, IPv4 address): The gateway of the local network.
|
||
- **subnet** (**Required**, IPv4 address): The subnet of the local network.
|
||
- **dns1** (*Optional*, IPv4 address): The main DNS server to use.
|
||
- **dns2** (*Optional*, IPv4 address): The backup DNS server to use.
|
||
|
||
- **use_address** (*Optional*, string): Manually override what address to use to connect
|
||
to the ESP. Defaults to auto-generated value. For example, if you have changed your
|
||
static IP and want to flash OTA to the previously configured IP address.
|
||
- **domain** (*Optional*, string): Set the domain of the node hostname used for uploading.
|
||
For example, if it's set to ``.local``, all uploads will be sent to ``<HOSTNAME>.local``.
|
||
Defaults to ``.local``.
|
||
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID used for code generation.
|
||
|
||
|
||
.. note::
|
||
|
||
If your ethernet board is not designed with an ESP32 built in, chances are that you are going
|
||
to use flying leads, dupont wires, etc. to connect the ethernet to the ESP32. This is
|
||
probably to fail as the ethernet interface uses a high frequency clock signal. For more
|
||
information and wiring details refer to the link in the *See also* section.
|
||
|
||
Configuration for wESP32 board
|
||
------------------------------
|
||
|
||
.. code-block:: yaml
|
||
|
||
ethernet:
|
||
type: LAN8720
|
||
mdc_pin: GPIO16
|
||
mdio_pin: GPIO17
|
||
clk_mode: GPIO0_IN
|
||
phy_addr: 0
|
||
|
||
Configuration for Olimex ESP32-POE
|
||
----------------------------------
|
||
|
||
.. code-block:: yaml
|
||
|
||
ethernet:
|
||
type: LAN8720
|
||
mdc_pin: GPIO23
|
||
mdio_pin: GPIO18
|
||
clk_mode: GPIO17_OUT
|
||
phy_addr: 0
|
||
power_pin: GPIO12
|
||
|
||
Configuration for Olimex ESP32-EVB
|
||
----------------------------------
|
||
|
||
.. code-block:: yaml
|
||
|
||
ethernet:
|
||
type: LAN8720
|
||
mdc_pin: GPIO23
|
||
mdio_pin: GPIO18
|
||
clk_mode: GPIO0_IN
|
||
phy_addr: 0
|
||
|
||
Configuration for LILYGO TTGO T-Internet-POE ESP32-WROOM LAN8270A Chip
|
||
----------------------------------------------------------------------
|
||
|
||
.. code-block:: yaml
|
||
|
||
ethernet:
|
||
type: LAN8720
|
||
mdc_pin: GPIO23
|
||
mdio_pin: GPIO18
|
||
clk_mode: GPIO17_OUT
|
||
phy_addr: 0
|
||
|
||
Configuration for OpenHacks LAN8720
|
||
-----------------------------------
|
||
|
||
.. code-block:: yaml
|
||
|
||
ethernet:
|
||
type: LAN8720
|
||
mdc_pin: GPIO23
|
||
mdio_pin: GPIO18
|
||
phy_addr: 1
|
||
|
||
Note: This board has an issue that might cause the ESP32 to boot in program mode. When testing, make sure you are monitoring the
|
||
serial output and reboot the device several times to see if it boots into the program properly.
|
||
|
||
Configuration for Wireless Tag WT32-ETH01
|
||
-----------------------------------------
|
||
|
||
.. code-block:: yaml
|
||
|
||
ethernet:
|
||
type: LAN8720
|
||
mdc_pin: GPIO23
|
||
mdio_pin: GPIO18
|
||
clk_mode: GPIO0_IN
|
||
phy_addr: 1
|
||
power_pin: GPIO16
|
||
|
||
See Also
|
||
--------
|
||
|
||
- :doc:`network`
|
||
- :apiref:`ethernet/ethernet_component.h`
|
||
- `ESP32 Ethernet PHY connection info <https://pcbartists.com/design/embedded/esp32-ethernet-phy-schematic-design/>`__
|
||
- :ghedit:`Edit`
|