mirror of
https://github.com/esphome/esphome-docs.git
synced 2024-11-15 10:45:41 +01:00
91 lines
3.2 KiB
ReStructuredText
91 lines
3.2 KiB
ReStructuredText
CSE7766 Power Sensor
|
|
====================
|
|
|
|
.. seo::
|
|
:description: Instructions for setting up CSE7766 power sensors for the Sonoff Pow R2
|
|
:image: cse7766.svg
|
|
:keywords: cse7766, cse7759b, Sonoff Pow R2
|
|
|
|
The ``cse7766`` sensor platform allows you to use your CSE7766 voltage/current and power sensors
|
|
(`datasheet <https://itead.cc/wp-content/uploads/2022/05/CSE7766.pdf>`__) sensors with
|
|
ESPHome. This sensor is commonly found in Sonoff POW R2. CSE7759B is similar to CSE7766
|
|
and works with this component.
|
|
|
|
.. note::
|
|
|
|
SAFETY HAZARD: Some devices such as Sonoff POWs/Shelly/etc, have the digital GND connected directly to mains voltage so **the GPIOs become LIVE during normal operation**. Our advice is to mark these boards to prevent any use of the dangerous digital pins.
|
|
|
|
As the communication with the CSE7766 done using UART, you need
|
|
to have an :ref:`UART bus <uart>` in your configuration with the ``rx_pin`` connected to the CSE7766.
|
|
Additionally, you need to set the baud rate to 4800. The device sends multiple updates per second, so you
|
|
will probably want some sort of averaging or throttle filter on the sensors.
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Example configuration entry
|
|
substitutions:
|
|
update_interval: 60s
|
|
|
|
# Disable logging over USB
|
|
logger:
|
|
baud_rate: 0
|
|
|
|
uart:
|
|
rx_pin: RX
|
|
baud_rate: 4800
|
|
|
|
sensor:
|
|
- platform: cse7766
|
|
current:
|
|
name: "Sonoff Pow R2 Current"
|
|
filters:
|
|
- throttle_average: ${update_interval}
|
|
voltage:
|
|
name: "Sonoff Pow R2 Voltage"
|
|
filters:
|
|
- throttle_average: ${update_interval}
|
|
power:
|
|
name: "Sonoff Pow R2 Power"
|
|
filters:
|
|
- throttle_average: ${update_interval}
|
|
energy:
|
|
name: "Sonoff Pow R2 Energy"
|
|
filters:
|
|
- throttle: ${update_interval}
|
|
apparent_power:
|
|
name: "Sonoff Pow R2 Apparent Power"
|
|
filters:
|
|
- throttle_average: ${update_interval}
|
|
power_factor:
|
|
name: "Sonoff Pow R2 Power Factor"
|
|
filters:
|
|
- throttle_average: ${update_interval}
|
|
.. note::
|
|
|
|
The configuration above should work for Sonoff POWs (R2).
|
|
|
|
Configuration variables:
|
|
------------------------
|
|
|
|
- **current** (*Optional*): Use the current value of the sensor in amperes. All options from
|
|
:ref:`Sensor <config-sensor>`.
|
|
- **power** (*Optional*): Use the (active) power value of the sensor in watts. All options from
|
|
:ref:`Sensor <config-sensor>`.
|
|
- **voltage** (*Optional*): Use the voltage value of the sensor in V (RMS).
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
- **energy** (*Optional*): Use the total energy value of the sensor in Wh.
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
- **apparent_power** (*Optional*): Use the apparent power value of the sensor in volt amps.
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
- **power_factor** (*Optional*): Use the power factor value of the sensor.
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
- **uart_id** (*Optional*, :ref:`config-id`): Manually specify the ID of the :ref:`UART Component <uart>` if you want
|
|
to use multiple UART buses.
|
|
|
|
See Also
|
|
--------
|
|
|
|
- :ref:`sensor-filters`
|
|
- :apiref:`cse7766/cse7766.h`
|
|
- :ghedit:`Edit`
|