mirror of
https://github.com/esphome/esphome-docs.git
synced 2024-11-19 11:25:25 +01:00
3b92289a08
* Added Etekcity Voltson cookbook * added esw01-eu images * Added cookbook link * Added esw01-eu cookbook image for index * Removed direct docu links
122 lines
3.3 KiB
ReStructuredText
122 lines
3.3 KiB
ReStructuredText
Etekcity Voltson (ESW01-EU)
|
|
===========================
|
|
|
|
.. seo::
|
|
:description: Configure an Etekcity Voltson and calculate the missing current sensor
|
|
:image: esw01-eu.jpg
|
|
:keywords: Etekcity, Voltson, ESW01, ESW01-EU, HLW8012, Home Assistant, ESPHome
|
|
|
|
|
|
The Etekcity Voltson brings a 10A relay, two LEDs (blue and yellow), a push button and a :doc:`/components/sensor/hlw8012`
|
|
in a very small package and at a reasonable price.
|
|
|
|
.. note::
|
|
|
|
There are quite a few hardware revisions out there. Also reginal versions like US, UK and EU are different.
|
|
|
|
Flashing
|
|
--------
|
|
|
|
Opening the case for flashing varies a lot for different hardware revisions. Mine was easy as it had two tiny T5 Torx screws in the front and four Philipps screws inside.
|
|
Once you have opened the case, remove the PCB from it and attach your TTL as follows:
|
|
|
|
5V and GND go to the bottom:
|
|
|
|
.. figure:: images/esw01-eu-pcb-bottom.jpg
|
|
:align: center
|
|
:width: 75.0%
|
|
|
|
On the opposite side, T12 is TX, T13 is RX. During boot you need to connect T11 and T16 pads to GND. Easiest is to flash with pogo pins.
|
|
|
|
.. figure:: images/esw01-eu-pcb-top.jpg
|
|
:align: center
|
|
:width: 75.0%
|
|
|
|
Configuration
|
|
-------------
|
|
|
|
As the Voltson has its SEL pin permanently pulled high, we are unable to switch from voltage measurement to current measurement.
|
|
This will be circumvented by defining the initial mode to be voltage measurement (see :doc:`/components/sensor/hlw8012` documentation)
|
|
and calculating the current with `Ohm's law <https://en.wikipedia.org/wiki/Ohm%27s_law>`_: ``P (watts) = V (volts) x I (amps)``
|
|
|
|
.. code-block:: yaml
|
|
|
|
esphome:
|
|
name: voltson
|
|
platform: ESP8266
|
|
board: esp01_1m
|
|
|
|
### you wifi and other settings here ###
|
|
|
|
### pins ###
|
|
# D1 GPIO5 | LED blue | status_led
|
|
# D0 GPIO16 | LED yellow | led1
|
|
# D5 GPIO14 | SW1 | button1
|
|
# D2 GPIO4 | REL1 | relay1
|
|
# D6 GPIO12 | HLW8012/CF1 | cf1_pin
|
|
# D7 GPIO13 | HLW8012/CF | cf_pin
|
|
|
|
status_led:
|
|
pin:
|
|
number: GPIO5
|
|
|
|
output:
|
|
- platform: gpio
|
|
id: relay1
|
|
pin: GPIO4
|
|
- platform: gpio
|
|
id: led1
|
|
pin: GPIO16
|
|
|
|
switch:
|
|
- platform: output
|
|
name: "Voltson Relay"
|
|
id: switch1
|
|
output: relay1
|
|
on_turn_on:
|
|
- output.turn_on: led1
|
|
on_turn_off:
|
|
- output.turn_off: led1
|
|
|
|
binary_sensor:
|
|
- platform: gpio
|
|
id: button1
|
|
pin:
|
|
number: GPIO14
|
|
mode: INPUT_PULLUP
|
|
inverted: true
|
|
on_press:
|
|
- switch.toggle: switch1
|
|
|
|
sensor:
|
|
- platform: hlw8012
|
|
sel_pin: 0 # not connected
|
|
cf_pin: GPIO13
|
|
cf1_pin: GPIO12
|
|
voltage:
|
|
id: hlw8012_voltage
|
|
name: "HLW8012 Voltage"
|
|
power:
|
|
id: hlw8012_power
|
|
name: "HLW8012 Power"
|
|
on_value:
|
|
- sensor.template.publish:
|
|
id: hlw8012_current_calculated
|
|
state: !lambda 'return id(hlw8012_power).state / id(hlw8012_voltage).state;'
|
|
update_interval: 10s
|
|
initial_mode: VOLTAGE
|
|
change_mode_every: 4294967295 # basically never
|
|
- platform: template
|
|
id: hlw8012_current_calculated
|
|
name: "HLW8012 Current (calculated)"
|
|
unit_of_measurement: A
|
|
accuracy_decimals: 2
|
|
|
|
|
|
|
|
See Also
|
|
--------
|
|
|
|
- :doc:`/components/sensor/hlw8012`
|
|
- :ghedit:`Edit`
|