mirror of
https://github.com/esphome/esphome-docs.git
synced 2024-11-14 10:35:27 +01:00
88e315e0e4
* Many example yaml tidy-ups * Update components/sensor/hlw8012.rst --------- Co-authored-by: Keith Burzinski <kbx81x@gmail.com>
174 lines
5.5 KiB
ReStructuredText
174 lines
5.5 KiB
ReStructuredText
Servo Component
|
|
===============
|
|
|
|
.. seo::
|
|
:description: Instructions for setting up servos in ESPHome
|
|
:image: servo.svg
|
|
|
|
The ``servo`` component allows you to use servo motors with ESPHome. Servos are
|
|
motor controllers that contain all the electronics necessary for driving the motor and provide
|
|
a simple PWM interface to control the motor.
|
|
|
|
This component works with both continuous-rotation and absolute servos and has a similar
|
|
interface to the Arduino Servo library.
|
|
|
|
First, create an :ref:`output component <output>` (here ``esp8266_pwm``) for the pin the
|
|
servo is connected to. Then connect that output to the servo component by assigning an ID.
|
|
Please note the frequency of the output should be around 50Hz, as most servo controllers
|
|
only operate in this frequency range.
|
|
|
|
.. note::
|
|
|
|
This component will not show up in the Home Assistant front-end automatically because
|
|
Home Assistant doesn't have support for servos. Please see :ref:`servo-ha-config`.
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Example configuration entry
|
|
servo:
|
|
- id: my_servo
|
|
output: pwm_output
|
|
|
|
# Example output platform
|
|
# On ESP32, use ledc output
|
|
output:
|
|
- platform: esp8266_pwm
|
|
id: pwm_output
|
|
pin: GPIOXX
|
|
frequency: 50 Hz
|
|
|
|
Configuration variables:
|
|
------------------------
|
|
|
|
- **output** (**Required**, :ref:`config-id`): The ID of the :doc:`output component </components/output/index>`
|
|
to use for this servo.
|
|
- **id** (**Required**, :ref:`config-id`): The ID of this servo so that it can be controlled.
|
|
|
|
Advanced Options:
|
|
|
|
- **min_level** (*Optional*, percentage): The PWM duty cycle the minimum value (-100%) will map
|
|
to. Defaults to ``3%``.
|
|
- **idle_level** (*Optional*, percentage): The PWM duty cycle the idle value (0%) will map
|
|
to. This is also the state of the servo at startup. Defaults to ``7.5%``.
|
|
- **max_level** (*Optional*, percentage): The PWM duty cycle the maximum value (100%) will map
|
|
to. Defaults to ``12.0%``.
|
|
- **restore** (*Optional*, boolean): Whether to restore the state of the servo motor at startup.
|
|
This is useful if you have an absolute servo motor and it goes back to its 0 position at startup.
|
|
Defaults to ``false``.
|
|
- **auto_detach_time** (*Optional*, :ref:`config-time`): The time after reaching the target value when the servo will be detached`, if set to zero, servo will not be detached. Defaults to ``0s``.
|
|
- **transition_length** (*Optional*, :ref:`config-time`): The time needed for a full movement (-1.0 to 1.0). This will effectively limit the speed of the servo, the larger the value, the slowest the servo will move. Defaults to ``0s``.
|
|
This can slow down the servo to avoid loud noises or just make the movement not jerking.
|
|
|
|
.. note::
|
|
|
|
Some servos support a larger range for the level. For continuous rotation servos
|
|
this can speed them up a bit and for absolute servos this can extend their angle range.
|
|
You can configure the ``min_level`` and ``max_level`` options to adjust the level range
|
|
to match your servo (Experiment with these values).
|
|
|
|
.. _servo-write_action:
|
|
|
|
``servo.write`` Action
|
|
----------------------
|
|
|
|
To use your servo motor in :ref:`automations <automation>` or templates, you can use this action to set the
|
|
target level of the servo from -100% to 100%.
|
|
|
|
- -100% (= -1.0) is the minimum value of the servo. For continuous-rotation servos this will
|
|
rotate the servo backward.
|
|
- 0% (= 0.0) is the idle level of the servo. For continuous-rotation servos this will
|
|
stop the servo.
|
|
- 100% (= 1.0) is the maximum value of the servo. For continuous-rotation servos this will
|
|
rotate the servo forward.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
then:
|
|
- servo.write:
|
|
id: my_servo
|
|
level: -100.0%
|
|
|
|
# Templated
|
|
- servo.write:
|
|
id: my_servo
|
|
# For template values, range is [-1; 1]
|
|
level: !lambda |-
|
|
if (id(my_binary_sensor).state) {
|
|
return 1.0;
|
|
} else {
|
|
return -1.0;
|
|
}
|
|
|
|
Configuration options:
|
|
|
|
- **id** (**Required**, :ref:`config-id`): The ID of the servo.
|
|
- **level** (*Optional*, percentage, :ref:`templatable <config-templatable>`): The target level.
|
|
Range is from -100% to 100% (-1.0 to 1.0).
|
|
|
|
.. note::
|
|
|
|
This action can also be expressed as a :ref:`lambda <config-lambda>`:
|
|
|
|
.. code-block:: cpp
|
|
|
|
id(my_servo).write(1.0);
|
|
|
|
.. _servo-detach_action:
|
|
|
|
``servo.detach`` Action
|
|
-----------------------
|
|
|
|
This :ref:`Action <config-action>` allows you to disable the output on a servo motor -
|
|
this will make the servo motor stop immediately and disable its active control.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
then:
|
|
- servo.detach: my_servo
|
|
|
|
.. note::
|
|
|
|
This action can also be expressed as a :ref:`lambda <config-lambda>`:
|
|
|
|
.. code-block:: cpp
|
|
|
|
id(my_servo).detach();
|
|
|
|
.. _servo-ha-config:
|
|
|
|
Home Assistant Configuration
|
|
----------------------------
|
|
|
|
The easiest way to control your servo from Home Assistant is to add a ``number`` to your ESPHome
|
|
configuration. See :ref:`Number <config-number>` for more information.
|
|
|
|
.. code-block:: yaml
|
|
|
|
number:
|
|
- platform: template
|
|
name: Servo Control
|
|
min_value: -100
|
|
initial_value: 0
|
|
max_value: 100
|
|
step: 1
|
|
optimistic: true
|
|
set_action:
|
|
then:
|
|
- servo.write:
|
|
id: my_servo
|
|
level: !lambda 'return x / 100.0;'
|
|
|
|
servo:
|
|
- platform: ...
|
|
# [...] servo config
|
|
id: my_servo
|
|
|
|
|
|
See Also
|
|
--------
|
|
|
|
- :apiref:`servo/servo.h`
|
|
- :ghedit:`Edit`
|