mirror of
https://github.com/esphome/esphome-docs.git
synced 2024-11-15 10:45:41 +01:00
74 lines
2.5 KiB
ReStructuredText
74 lines
2.5 KiB
ReStructuredText
Power Supply Component
|
||
======================
|
||
|
||
.. seo::
|
||
:description: Instructions for setting up power supplies which will automatically turn on together with outputs.
|
||
:image: power.svg
|
||
:keywords: power, ATX
|
||
|
||
The ``power_supply`` component allows you to have a high power mode for
|
||
certain outputs. For example, if you’re using an `ATX power
|
||
supply <https://en.wikipedia.org/wiki/ATX>`__ to power your LED strips,
|
||
you usually don’t want to have the power supply on all the time while
|
||
the output is not on. The power supply component can be attached to any
|
||
:ref:`Output Component <output>` and
|
||
will automatically switch on if any of the outputs are on. Furthermore,
|
||
it also has a cooldown time that keeps the power supply on for a while
|
||
after the last output has been disabled.
|
||
|
||
.. code-block:: yaml
|
||
|
||
# Example configuration entry
|
||
power_supply:
|
||
- id: 'power_supply1'
|
||
pin: 13
|
||
|
||
Configuration variables:
|
||
------------------------
|
||
|
||
- **id** (**Required**, :ref:`config-id`): The id of the
|
||
power supply so that it can be used by the outputs.
|
||
- **pin** (**Required**, :ref:`Pin Schema <config-pin_schema>`): The
|
||
GPIO pin to control the power supply on.
|
||
- **enable_time** (*Optional*, :ref:`config-time`): The time to
|
||
that the power supply needs for startup. The output component will
|
||
wait for this period of time after turning on the PSU and before
|
||
switching the output on. Defaults to ``20ms``.
|
||
- **keep_on_time** (*Optional*, :ref:`config-time`): The time the
|
||
power supply should be kept enabled after the last output that used
|
||
it has been switch off. Defaults to ``10s``.
|
||
|
||
See the :ref:`output component base configuration <config-output>`
|
||
for information on how to apply the power supply for a specific output.
|
||
|
||
ATX Power Supplies
|
||
------------------
|
||
|
||
.. figure:: images/power_supply-atx.jpg
|
||
:align: center
|
||
:width: 80.0%
|
||
|
||
The power supply component will default to pulling the specified GPIO
|
||
pin up when high power mode is needed. Most ATX power supplies however
|
||
operate with an active-low configuration. Therefore their output needs
|
||
to be inverted.
|
||
|
||
.. code-block:: yaml
|
||
|
||
power_supply:
|
||
- id: 'atx_power_supply'
|
||
pin:
|
||
number: 13
|
||
inverted: true
|
||
|
||
Then simply connect the green control wire from the ATX power supply to
|
||
your specified pin. It’s recommended to put a small resistor (about 1kΩ)
|
||
in between to protect the ESP board.
|
||
|
||
See Also
|
||
--------
|
||
|
||
- :doc:`output/index`
|
||
- :apiref:`power_supply/power_supply.h`
|
||
- :ghedit:`Edit`
|