esphome-docs/components/sensor/qmc5883l.rst

92 lines
3.2 KiB
ReStructuredText

QMC5883L Magnetometer
=====================
.. seo::
:description: Instructions for setting up QMC5883L IMU compass sensors.
:image: qmc5883l.jpg
:keywords: QMC5883L
The ``qmc5883l`` allows you to use your QMC5883L triple-axis magnetometers
(`datasheet <http://wiki.sunfounder.cc/images/7/72/QMC5883L-Datasheet-1.0.pdf>`__) with
ESPHome. This sensor is very simular to the :ref:`HMC5883L <hmc5883l>` sensor and is oftern found
as a knock off replacement. The QMC5883L sensor performs on par to the HMC5883L sensor,
though the configuration differs. The :ref:`I²C Bus <i2c>` is required to be set up in your
configuration for this sensor to work.
.. figure:: ../../images/qmc5883l.jpg
:align: center
:width: 30.0%
QMC5883L Magnetometer.
.. code-block:: yaml
# Example configuration entry
sensor:
- platform: qmc5883l
address: 0x0D
field_strength_x:
name: "QMC5883L Field Strength X"
field_strength_y:
name: "QMC5883L Field Strength Y"
field_strength_z:
name: "QMC5883L Field Strength Z"
heading:
name: "QMC5883L Heading"
temperature:
name: "QMC5883L Temperature"
filters:
- offset: 34.0
range: 200uT
oversampling: 512x
update_interval: 60s
Configuration variables:
------------------------
- **address** (*Optional*, int): Manually specify the I²c address of the sensor. Defaults to ``0x0D``.
- **field_strength_x** (*Optional*): The field strength in microtesla along the X-Axis. All options from
:ref:`Sensor <config-sensor>`.
- **field_strength_y** (*Optional*): The field strength in microtesla along the Y-Axis. All options from
:ref:`Sensor <config-sensor>`.
- **field_strength_z** (*Optional*): The field strength in microtesla along the Z-Axis. All options from
:ref:`Sensor <config-sensor>`.
- **heading** (*Optional*): The heading of the sensor in degrees. All options from
:ref:`Sensor <config-sensor>`.
- **temperature** (*Optional*): The temperature of the sensor. Per the datasheet:
"Temperature sensor gain is factory-calibrated, but its offset has not been compensated, only relative
temperature value is accurate". Above example has an offset that you need to calibrate. All options from
:ref:`Sensor <config-sensor>`.
- **range** (*Optional*): The range parameter for the sensor.
- **oversampling** (*Optional*): The oversampling parameter for the sensor.
- **update_interval** (*Optional*, :ref:`config-time`): The interval to check the sensor. Defaults to ``60s``.
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID used for code generation.
Range Options
-------------
By default, the QMC5883L sensor measurement range is 200µT. You can, however,
configure this amount. Possible values:
- ``200µT`` (default)
- ``800µT``
Oversampling Options
--------------------
By default, the QMC5883L sensor measures each value 512 times when requesting a new value. You can, however,
configure this amount. The result is the sensor will take the adverage of the x samples. Possible sampling values:
- ``512x`` (default)
- ``256x``
- ``128x``
- ``64x``
See Also
--------
- :ref:`sensor-filters`
- :doc:`template`
- :apiref:`qmc5883l/qmc5883l.h`
- :ghedit:`Edit`