mirror of
https://github.com/esphome/esphome-docs.git
synced 2024-12-24 17:08:15 +01:00
125 lines
4.8 KiB
ReStructuredText
125 lines
4.8 KiB
ReStructuredText
Sonoff D1 Dimmer
|
|
================
|
|
|
|
.. seo::
|
|
:description: Instructions for setting up a Sonoff D1 dimmer switch.
|
|
:image: brightness-medium.svg
|
|
|
|
The ``sonoff_d1`` light platform creates a simple brightness-only light for the
|
|
hardware found in `Sonoff D1 dimmer <https://itead.cc/product/sonoff-d1-smart-dimmer-switch/>`__. Installations with Sonoff RM433 433MHz radio
|
|
remotes are also supported. Use this component to integrate Sonoff D1 dimmer into
|
|
ESPHome / Home Assistant ecosystem.
|
|
|
|
.. figure:: images/sonoff_d1.jpg
|
|
:align: center
|
|
:width: 100.0%
|
|
|
|
Sonoff D1 dimmer front and back view. Image by `ITEAD <https://itead.cc/product/sonoff-d1-smart-dimmer-switch/>`__.
|
|
|
|
Sonoff D1 uses another MCU for light dimming and handling of radio commands.
|
|
It's hooked up to ESP8266 via UART bus with default RX / TX pins being used on
|
|
ESP8266 side. Bi-directional symmetric request / response protocol is implemented
|
|
between ESP8266 and MCU. ``sonoff_d1`` component implements this protocol and
|
|
translates between HA light commands and serial messages.
|
|
|
|
For detailed instructions on how to replace the stock firmware with ESPHome see :doc:`/devices/sonoff_s20`.
|
|
You will need to locate GPIO0 pin and serial port. Photos below should help.
|
|
|
|
.. figure:: images/sonoff_d1_gpio0.jpg
|
|
:align: center
|
|
:width: 100.0%
|
|
|
|
Photo of GPIO 0, images by `klotzma <https://github.com/arendst/Tasmota/issues/7598#issuecomment-578433417>`__.
|
|
.. figure:: images/sonoff_d1_serial.jpg
|
|
:align: center
|
|
:width: 100.0%
|
|
|
|
Photo of serial port pins, images by `klotzma <https://github.com/arendst/Tasmota/issues/7598#issuecomment-578433417>`__.
|
|
|
|
Before using this components make sure:
|
|
|
|
- board is configured to ``esp8285``
|
|
- :ref:`UART bus <uart>` is configured with default RX / TX pins and 9600 baud rate
|
|
- :doc:`logger </components/logger>` to the serial port is disabled by setting ``baud_rate`` to ``0``
|
|
- in case you need light state restoration on power up, make sure ``restore_from_flash`` is set to ``true`` in the :doc:`ESP8266 platform </components/esp8266>`
|
|
|
|
|
|
This component is useless for devices other than Sonoff D1 dimmer.
|
|
|
|
.. code-block:: yaml
|
|
|
|
|
|
# Example configuration entry
|
|
esphome:
|
|
name: my-d1-dimmer
|
|
|
|
# Restore from flash if you want to keep the last state at power up
|
|
esp8266:
|
|
board: esp8285
|
|
restore_from_flash: true
|
|
|
|
# Make sure your WiFi will connect
|
|
wifi:
|
|
ssid: "ssid"
|
|
password: "password"
|
|
|
|
# Make sure logging is not using the serial port
|
|
logger:
|
|
baud_rate: 0
|
|
|
|
# Enable Home Assistant API
|
|
api:
|
|
|
|
# Make sure you can upload new firmware OTA
|
|
ota:
|
|
|
|
# D1 dimmer uses hardware serial port on the default pins @ 9600 bps
|
|
uart:
|
|
rx_pin: RX
|
|
tx_pin: TX
|
|
baud_rate: 9600
|
|
|
|
# And finally the light component
|
|
# gamma correction equal to zero gives linear scale,
|
|
# exactly what's needed for this device
|
|
light:
|
|
- platform: sonoff_d1
|
|
use_rm433_remote: False
|
|
name: Sonoff D1 Dimmer
|
|
restore_mode: RESTORE_DEFAULT_OFF
|
|
gamma_correct: 0.0
|
|
default_transition_length: 1s
|
|
|
|
|
|
Configuration variables:
|
|
------------------------
|
|
|
|
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID used for code generation.
|
|
- **name** (**Required**, string): The name of the light.
|
|
- **use_rm433_remote** (*Optional*, boolean): Set to ``True`` if your setup uses Sonoff RM433
|
|
or any other radio remote control. Properly setting this parameter allows the platform to
|
|
identify what to do with incoming UART commands. RF chip is known to catch random commands
|
|
if not paired with a real remote (so called ghost commands). This problem is observed even
|
|
with the stock firmware and most probably is a bug in the MCU firmware or in the RF chip
|
|
firmware. Setting this to ``False`` instructs the platform to properly ignore such commands
|
|
and thus prevent unexpected switches or light intensity changes.
|
|
- **min_value** (*Optional*, int): The lowest dimmer value allowed. Acceptable value for your
|
|
setup will depend on actual light bulbs installed and number of them. Start with the default
|
|
value and check what will be the minimal brightness bulbs can render. Pay attention that for
|
|
some dimmable LED lamps minimal turn-on brightness will be higher that the minimal achievable
|
|
brightness if you just decrease it when lamp is already turned on. Defaults to 0.
|
|
- **max_value** (*Optional*, int): The highest dimmer value allowed. Use this to hard-limit light
|
|
intensity for your setup. For some bulbs this parameter might be also useful to prevent
|
|
flickering at high brightness values. Defaults to 100.
|
|
- All other options from :ref:`Light <config-light>`.
|
|
|
|
|
|
See Also
|
|
--------
|
|
|
|
- :doc:`/components/light/index`
|
|
- :doc:`/components/uart`
|
|
- :doc:`/components/logger`
|
|
- :doc:`/components/esp8266`
|
|
- :ghedit:`Edit`
|