mirror of
https://github.com/esphome/esphome-docs.git
synced 2024-11-07 09:43:08 +01:00
71279eccde
* More descriptive information for noobs The original doc was fairly bare and has led to some confusion, especially around naming and other "magic". I've added more description to make this easier to understand. * Minor changes * Update formatting Co-authored-by: Fabian Affolter <mail@fabian-affolter.ch>
351 lines
13 KiB
ReStructuredText
351 lines
13 KiB
ReStructuredText
Stepper Component
|
|
=================
|
|
|
|
.. seo::
|
|
:description: Instructions for setting up stepper motor drivers in ESPHome
|
|
:image: folder-open.png
|
|
:keywords: stepper motor, stepper driver, a4988
|
|
|
|
The ``stepper`` component allows you to use stepper motors with ESPHome.
|
|
Currently only the A4988 stepper driver
|
|
(`datasheet <https://www.pololu.com/file/0J450/a4988_DMOS_microstepping_driver_with_translator.pdf>`__)
|
|
and ULN2003 (`datasheet <http://www.ti.com/lit/ds/symlink/uln2003a.pdf>`__) are supported.
|
|
|
|
.. note::
|
|
|
|
This component will not show up in the Home Assistant front-end automatically because
|
|
Home Assistant doesn't have support for steppers. Please see :ref:`stepper-ha-config`.
|
|
|
|
A4988 Configuration
|
|
-------------------
|
|
|
|
Put this code into the configuration file on ESPhome for this device.
|
|
|
|
.. code-block:: yaml
|
|
|
|
stepper:
|
|
- platform: a4988
|
|
id: my_stepper
|
|
step_pin: D0
|
|
dir_pin: D1
|
|
max_speed: 250 steps/s
|
|
|
|
# Optional:
|
|
sleep_pin: D2
|
|
acceleration: inf
|
|
deceleration: inf
|
|
|
|
|
|
Configuration variables:
|
|
|
|
- **id** (**Required**, :ref:`config-id`): Specify the ID of the stepper so that you can control it.
|
|
- **step_pin** (**Required**, :ref:`Pin Schema <config-pin_schema>`): The ``STEP`` pin of the A4988
|
|
stepper driver.
|
|
- **dir_pin** (**Required**, :ref:`Pin Schema <config-pin_schema>`): The ``DIRECTION`` pin of the A4988
|
|
stepper driver.
|
|
- **max_speed** (**Required**, float): The maximum speed in ``steps/s`` (steps per seconds) to drive the
|
|
stepper at. Note most steppers can't step properly with speeds higher than 250 steps/s.
|
|
- **sleep_pin** (*Optional*, :ref:`Pin Schema <config-pin_schema>`): Optionally also use the ``SLEEP`` pin
|
|
of the A4988 stepper driver. If specified, the driver will be put into sleep mode as soon as the stepper
|
|
reaches the target steps.
|
|
- **acceleration** (*Optional*, float): The acceleration in ``steps/s^2`` (steps per seconds squared)
|
|
to use when starting to move. The default is ``inf`` which means infinite acceleration, so the
|
|
stepper will try to drive with the full speed immediately.
|
|
- **deceleration** (*Optional*, float): The same as ``acceleration``, but for when the motor is decelerating
|
|
shortly before reaching the set position. Defaults to ``inf`` (immediate deceleration).
|
|
|
|
.. note::
|
|
|
|
If the stepper is driving in the wrong direction, you can invert the ``dir_pin``:
|
|
|
|
.. code-block:: yaml
|
|
|
|
stepper:
|
|
- platform: a4988
|
|
# ...
|
|
dir_pin:
|
|
number: D1
|
|
inverted: True
|
|
|
|
ULN2003 Configuration
|
|
---------------------
|
|
|
|
Put this code into the configuration file on ESPHome for this device.
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Example configuration entry
|
|
stepper:
|
|
- platform: uln2003
|
|
id: my_stepper
|
|
pin_a: D0
|
|
pin_b: D1
|
|
pin_c: D2
|
|
pin_d: D3
|
|
max_speed: 250 steps/s
|
|
|
|
# Optional:
|
|
acceleration: inf
|
|
deceleration: inf
|
|
|
|
|
|
Configuration variables:
|
|
|
|
- **id** (**Required**, :ref:`config-id`): Specify the ID of the stepper so that you can control it.
|
|
- **pin_a**, **pin_b**, **pin_c**, **pin_d** (**Required**, :ref:`Pin Schema <config-pin_schema>`):
|
|
The four pins of the stepper control board.
|
|
- **sleep_when_done** (*Optional*, boolean): Whether to turn off all coils when the stepper has
|
|
reached the target position
|
|
- **step_mode** (*Optional*, string): The step mode to operate the motor with. One of:
|
|
|
|
- ``FULL_STEP`` (Default)
|
|
- ``HALF_STEP``
|
|
- ``WAVE_DRIVE``
|
|
|
|
- **max_speed** (**Required**, float): The maximum speed in ``steps/s`` (steps per seconds) to drive the
|
|
stepper at. Note most steppers can't step properly with speeds higher than 250 steps/s.
|
|
- **acceleration** (*Optional*, float): The acceleration in ``steps/s^2`` (steps per seconds squared)
|
|
to use when starting to move. The default is ``inf`` which means infinite acceleration, so the
|
|
stepper will try to drive with the full speed immediately. This value is helpful if that first motion of
|
|
the motor is too jerky for what it's moving. If you make this a small number, it will take the motor a
|
|
moment to get up to speed.
|
|
- **deceleration** (*Optional*, float): The same as ``acceleration``, but for when the motor is decelerating
|
|
shortly before reaching the set position. Defaults to ``inf`` (immediate deceleration).
|
|
|
|
.. _stepper-set_target_action:
|
|
|
|
``stepper.set_target`` Action
|
|
-----------------------------
|
|
|
|
To use your stepper motor in :ref:`automations <automation>` or templates, you can use this action to set the target
|
|
position (in steps). The stepper will always run towards the target position and stop once it has reached the target.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
then:
|
|
- stepper.set_target:
|
|
id: my_stepper
|
|
target: 250
|
|
|
|
# Templated
|
|
- stepper.set_target:
|
|
id: my_stepper
|
|
target: !lambda |-
|
|
if (id(my_binary_sensor).state) {
|
|
return 1000;
|
|
} else {
|
|
return -1000;
|
|
}
|
|
|
|
Configuration options:
|
|
|
|
- **id** (**Required**, :ref:`config-id`): The ID of the stepper.
|
|
- **target** (*Optional*, int, :ref:`templatable <config-templatable>`): The target position in steps.
|
|
|
|
.. warning::
|
|
|
|
This turns the stepper to an absolute position! To have the servo move *relative* to the current
|
|
position, first reset the current position and then set the target to the relative value.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
then:
|
|
# Move 150 steps forward
|
|
- stepper.report_position:
|
|
id: my_stepper
|
|
position: 0
|
|
- stepper.set_target:
|
|
id: my_stepper
|
|
target: 150
|
|
|
|
.. _stepper-report_position_action:
|
|
|
|
``stepper.report_position`` Action
|
|
----------------------------------
|
|
|
|
All steppers start out with a target and current position of ``0`` on boot. However, if you for example want to home
|
|
a stepper motor, it can be useful to **report** the stepper where it is currently at.
|
|
|
|
With this action, you can set the stepper's internal position counter to a specific value (in steps). Please note
|
|
that reporting the position can create unexpected moves of the stepper. For example, if the stepper's target and
|
|
current position is at 1000 steps and you "report" a position of 0, the stepper will move 1000 steps forward to match
|
|
the target again.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
then:
|
|
- stepper.report_position:
|
|
id: my_stepper
|
|
position: 250
|
|
# It's best to call set_target directly after report_position, so that the stepper doesn't move
|
|
- stepper.set_target:
|
|
id: my_stepper
|
|
target: 250
|
|
|
|
# Templated
|
|
- stepper.report_position:
|
|
id: my_stepper
|
|
position: !lambda |-
|
|
if (id(my_binary_sensor).state) {
|
|
return 0;
|
|
} else {
|
|
return -1000;
|
|
}
|
|
|
|
Configuration options:
|
|
|
|
- **id** (**Required**, :ref:`config-id`): The ID of the stepper.
|
|
- **target** (*Optional*, int, :ref:`templatable <config-templatable>`): The target position in steps.
|
|
|
|
.. _stepper-set_speed_action:
|
|
|
|
``stepper.set_speed`` Action
|
|
----------------------------
|
|
|
|
This :ref:`Action <config-action>` allows you to set the speed of a stepper at runtime.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
- stepper.set_speed:
|
|
id: my_stepper
|
|
speed: 250 steps/s
|
|
|
|
Configuration variables:
|
|
|
|
- **id** (**Required**, :ref:`config-id`): The ID of the stepper.
|
|
- **speed** (**Required**, :ref:`templatable <config-templatable>`, float): The speed
|
|
in ``steps/s`` (steps per seconds) to drive the stepper at.
|
|
|
|
.. _stepper-ha-config:
|
|
|
|
Home Assistant Configuration
|
|
----------------------------
|
|
|
|
This component will not show up in the Home Assistant front-end (Overview) automatically because
|
|
Home Assistant does not support steppers natively.
|
|
|
|
You can add the stepper component code below to your Home Assistant configuration (``configuration.yaml``) to
|
|
be able to control the stepper from the front-end.
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Add a slider control to Home Assistant to set an integer value
|
|
input_number:
|
|
stepper_control:
|
|
name: Stepper Control
|
|
initial: 0
|
|
min: -1000
|
|
max: 1000
|
|
step: 1
|
|
mode: slider
|
|
|
|
# Do something when the slider changes
|
|
automation:
|
|
- alias: Write Stepper Value to ESP
|
|
trigger:
|
|
platform: state
|
|
entity_id: input_number.stepper_control
|
|
action:
|
|
# Replace livingroom with the name you gave the ESP
|
|
- service: esphome.livingroom_control_stepper
|
|
data_template:
|
|
target: '{{ trigger.to_state.state | int }}'
|
|
|
|
In the above code, "stepper_control" is the ID of a numeric input field. It must be unique and it is
|
|
used in the automation section as a reference name. The display name for this field is in
|
|
stepper_control's ``name`` key.
|
|
|
|
If you want your user interface to give you more control over your stepper controller, such as
|
|
setting the acceleration, deceleration, etc, then you can add more input fields after ``stepper_control``
|
|
but before ``automation``. They can be a simple number-entry field (mode: box) or a slider like this.
|
|
Each of these extra input fields needs an associated input parameter defined on the ESPHome device's
|
|
API service.
|
|
|
|
The automation section tells Home Assistant what to do when the slider changes. It needs a trigger
|
|
(state of the ``stepper_control`` slider) and an action. In the trigger section, ``entity_id`` must refer
|
|
back to the configuration ID that triggers the automation. For us, that is the ``stepper_control``
|
|
field in the ``input_number`` item. That's why the value is ``input_number.stepper_control``.
|
|
|
|
In the action section, the service name is vital to get right: it's the glue that connects Home Automation's
|
|
front-end to the ESPHome device configuration. While you might expect the syntax to be ``esphome.<your_device>.<api_service>``,
|
|
the correct syntax is to join the device ID to the API service ID with an underscore,
|
|
as in ``esphome.livingroom_control_stepper`` where "Livingroom" is a device in ESPHome and "control_stepper" is an
|
|
API service for that device.
|
|
|
|
The template string is used to get the "state" value from the ``target`` field (defined in the target section) on the
|
|
``input_number`` component of the Home Assistant front-end. This value is then passed to the API service as defined in
|
|
the ESPHome device's configuration. The ``data_template`` section lists one value for each of the input parameters on
|
|
the service being called by the automation. In our case, the ESPHome device has an API service with a single parameter,
|
|
"target". If you called this "my_target", then the last line above should be ``my_target: '{{ trigger.to_state.state | int }}'``.
|
|
Getting this linkage right is very important.
|
|
|
|
The following code needs to go in the ESPHome configuration file for this device. Above, we mention "API service"
|
|
a lot. This code is where that is defined. You may have already added it (or something similar). Note
|
|
that the input variable for the ``control_stepper`` service is called ``target``. That's what matches with the
|
|
automation configuration above. Also note that the variable ``target`` is defined as an integer. That means it
|
|
must be an integer number, not a string.
|
|
|
|
.. code-block:: yaml
|
|
|
|
# ESPHome configuration
|
|
api:
|
|
services:
|
|
- service: control_stepper
|
|
variables:
|
|
target: int
|
|
then:
|
|
- stepper.set_target:
|
|
id: my_stepper
|
|
target: !lambda 'return target;'
|
|
|
|
stepper:
|
|
- platform: ...
|
|
# [...] stepper config
|
|
id: my_stepper
|
|
|
|
.. _stepper-lambda_calls:
|
|
|
|
lambda calls
|
|
------------
|
|
|
|
From :ref:`lambdas <config-lambda>`, you can call several methods on stepper motors to do some
|
|
advanced stuff (see the full API Reference for more info).
|
|
|
|
- ``set_target``: Set the target position of the motor as an integer.
|
|
|
|
.. code-block:: cpp
|
|
|
|
// Argument is integer (signed int)
|
|
// Set the (absolute) target position to 250 steps
|
|
id(my_stepper).set_target(250);
|
|
|
|
- ``report_position``: Report the current position as an integer.
|
|
|
|
.. code-block:: cpp
|
|
|
|
// Report the (absolute) current position as 250 steps
|
|
id(my_stepper).report_position(250);
|
|
|
|
- ``current_position``: Get the current position of the stepper as an integer.
|
|
|
|
.. code-block:: cpp
|
|
|
|
int pos = id(my_stepper).current_position;
|
|
|
|
|
|
- ``target_position``: Get the set target position of the stepper as an integer.
|
|
|
|
.. code-block:: cpp
|
|
|
|
int pos = id(my_stepper).target_position;
|
|
|
|
See Also
|
|
--------
|
|
|
|
- :apiref:`stepper/stepper.h`
|
|
- :ghedit:`Edit`
|