mirror of
https://github.com/esphome/esphome-docs.git
synced 2024-12-30 18:09:26 +01:00
80 lines
3.5 KiB
ReStructuredText
80 lines
3.5 KiB
ReStructuredText
TMP1075 Temperature Sensor
|
|
==========================
|
|
|
|
.. seo::
|
|
:description: Instructions for setting up the TMP1075 Temperature sensor.
|
|
:image: tmp1075.jpg
|
|
:keywords: TMP1075
|
|
|
|
The TMP1075 Temperature sensor allows you to use your TMP1075
|
|
(`datasheet <https://www.ti.com/lit/gpn/tmp1075>`__)
|
|
sensors with ESPHome.
|
|
|
|
.. figure:: images/tmp1075.jpg
|
|
:align: center
|
|
:width: 30.0%
|
|
|
|
TMP1075 Temperature Sensor.
|
|
(Credit: `Texas Instruments <https://www.ti.com/content/dam/ticom/images/products/ic/sensing-products/chips/tmp1075-technical-chip-shot.png>`__, image cropped and compressed)
|
|
|
|
The TMP1075 is a high precision temperature sensor that communicates over I²C.
|
|
Each sensor is tested on a NIST tracable test setup during Texas Instruments'
|
|
production process. Accuracy is typically ±0.25°C across the -55°C to +125°C
|
|
range, with a maximum error of ±2°C in that same range and ±1°C in the -40°C to
|
|
+110°C range.
|
|
|
|
To use the sensor, first set up an :ref:`I²C Bus <i2c>` and connect the sensor
|
|
to the specified pins.
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Example configuration entry
|
|
sensor:
|
|
- platform: tmp1075
|
|
name: "Temperature TMP1075"
|
|
update_interval: 10s
|
|
i2c_id: i2c_bus
|
|
conversion_rate: 27.5ms
|
|
alert:
|
|
function: comparator
|
|
polarity: active_high
|
|
limit_low: 50
|
|
limit_high: 75
|
|
fault_count: 1
|
|
|
|
Configuration variables:
|
|
------------------------
|
|
|
|
- **name** (**Required**, string): The name for the temperature sensor.
|
|
- **id** (*Optional*, :ref:`config-id`): Set the ID of this sensor for lambdas/multiple sensors.
|
|
- **address** (*Optional*, int): The I²C address of the sensor.
|
|
See :ref:`I²C Addresses <tmp1075_i2c_addresses>` for more information. Defaults to ``0x48``.
|
|
- **update_interval** (*Optional*, :ref:`config-time`): The interval to check
|
|
the sensor temperature. Defaults to ``60s``.
|
|
- **conversion_rate** (*Optional*): The interval at which the IC performs a
|
|
temperature measurement. This setting also determines how fast the alert pin
|
|
responds to temperature changes, and is thus independent of how often ESPHome
|
|
checks the sensor. Possible values are ``27.5ms``, ``55ms``, ``110ms``, and
|
|
``220ms``. Defaults to ``27.5ms``.
|
|
- **alert** (*Optional*): Configure the alert pin behaviour.
|
|
|
|
- **function** (*Optional*, enum): Function of the alert pin, either ``comparator`` or ``interrupt``. Defaults to ``comparator``.
|
|
- **polarity** (*Optional*, enum): Polarity of the alert pin, either ``active_high`` or ``active_low``. Defaults to ``active_high``.
|
|
- **limit_low** (*Optional*, int): Lower temperature limit, in °C. Defaults to ``-128`` (the lowest possible limit value).
|
|
- **limit_high** (*Optional*, int): Higher temperature limit, in °C. Defaults to ``127.9375`` (the highest possible limit value).
|
|
- **fault_count** (*Optional*, int): Number of measurements. required for the alert pin to act. Must be between ``1`` and ``4``, inclusive. Defaults to ``1``.
|
|
|
|
.. _tmp1075_i2c_addresses:
|
|
|
|
I²C Addresses
|
|
-------------
|
|
|
|
In order to allow multiple sensors to be connected to the same I²C bus, the
|
|
creators of this sensor hardware have included some options to change the I²C
|
|
address. Three address pins can be connected to GND, VCC, SDA, or SCL, creating
|
|
32 possible addresses. See section 9.3.2.2 of the `datasheet
|
|
<https://www.ti.com/lit/gpn/tmp1075>`__ for the mapping table.
|
|
|
|
When all address pins are connected to GND, the address is ``0x48``, which is
|
|
the default address for this sesnsor component.
|