mirror of
https://github.com/esphome/esphome-docs.git
synced 2024-11-05 09:20:08 +01:00
f99ee565a4
Adds information about the LCD modules which are often sold with/for these sensors, and using them in conjunction with an ESP. Also notes that INPUT_PULLDOWN mode may help with reliability, and aligns some of the config descriptions with other air quality sensors.
140 lines
5.4 KiB
ReStructuredText
140 lines
5.4 KiB
ReStructuredText
SM300D2 7-in-1 Air Quality Sensor
|
|
=================================
|
|
|
|
.. seo::
|
|
:description: Instructions for setting up SM300D2 sensor to work with ESPHome
|
|
:image: sm300d2.jpg
|
|
:keywords: sm300d2
|
|
|
|
The ``sm300d2`` sensor platform allows you to use the SM300D2 7-in-1 Air Quality Sensor with ESPHome.
|
|
|
|
.. figure:: images/sm300d2-full.jpg
|
|
:align: center
|
|
:width: 50.0%
|
|
|
|
SM300D2 7-in-1 Air Quality Sensor.
|
|
|
|
.. figure:: images/sm300d2-ui.png
|
|
:align: center
|
|
:width: 50.0%
|
|
|
|
|
|
Although the SM300D2 sensor supports connections via UART or RS485, this platform only supports UART
|
|
connections. The LCD module which is often sold with/for these sensor boards can work over either UART
|
|
or RS485, so you can use the LCD over RS485 and an ESP over UART at the same time (see
|
|
:ref:`note below <pins-note>` regarding powering everything).
|
|
|
|
Make sure you have a :ref:`UART bus <uart>` in your configuration with the ``rx_pin`` connected to the
|
|
sensor's TX pin. The sensor does not support receiving data, so the ``tx_pin`` does not need to be
|
|
connected. The UART bus should be set to a baud rate of 9600 to match the sensor's output. Setting the
|
|
``rx_pin``'s mode to ``INPUT_PULLDOWN`` may help improve reliability if you're regularly getting missed
|
|
or bad/incomplete readings.
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Example configuration entry
|
|
uart:
|
|
rx_pin:
|
|
number: D0
|
|
mode: INPUT_PULLDOWN
|
|
tx_pin: D1
|
|
baud_rate: 9600
|
|
|
|
sensor:
|
|
- platform: sm300d2
|
|
co2:
|
|
name: "SM300D2 CO2 Value"
|
|
formaldehyde:
|
|
name: "SM300D2 Formaldehyde Value"
|
|
tvoc:
|
|
name: "SM300D2 TVOC Value"
|
|
pm_2_5:
|
|
name: "SM300D2 PM2.5 Value"
|
|
pm_10_0:
|
|
name: "SM300D2 PM10 Value"
|
|
temperature:
|
|
name: "SM300D2 Temperature Value"
|
|
humidity:
|
|
name: "SM300D2 Humidity Value"
|
|
update_interval: 60s
|
|
|
|
Configuration variables:
|
|
------------------------
|
|
|
|
|
|
- **co2** (**Required**): The information for the CO₂ sensor. Readings in parts per million (ppm).
|
|
|
|
- **name** (**Required**, string): The name of the CO₂ sensor.
|
|
- **id** (*Optional*, :ref:`config-id`): Set the ID of this sensor for use in lambdas.
|
|
- All other options from :ref:`Sensor <config-sensor>`.
|
|
|
|
- **formaldehyde** (**Required**): The information for the formaldehyde sensor. Readings in µg/m³.
|
|
|
|
- **name** (**Required**, string): The name of the formaldehyde sensor.
|
|
- **id** (*Optional*, :ref:`config-id`): Set the ID of this sensor for use in lambdas.
|
|
- All other options from :ref:`Sensor <config-sensor>`.
|
|
|
|
- **tvoc** (**Required**): The information for the total volatile organic compounds (TVOC) sensor. Readings in µg/m³.
|
|
|
|
- **name** (**Required**, string): The name of the TVOC sensor.
|
|
- **id** (*Optional*, :ref:`config-id`): Set the ID of this sensor for use in lambdas.
|
|
- All other options from :ref:`Sensor <config-sensor>`.
|
|
|
|
- **pm_2_5** (**Required**): The information for the **Weight Concentration** sensor for fine particles up to 2.5μm. Readings in µg/m³.
|
|
|
|
- **name** (**Required**, string): The name of the PM2.5 sensor.
|
|
- **id** (*Optional*, :ref:`config-id`): Set the ID of this sensor for use in lambdas.
|
|
- All other options from :ref:`Sensor <config-sensor>`.
|
|
|
|
- **pm_10_0** (**Required**): The information for the **Weight Concentration** sensor for coarse particles up to 10μm. Readings in µg/m³.
|
|
|
|
- **name** (**Required**, string): The name of the PM10 sensor.
|
|
- **id** (*Optional*, :ref:`config-id`): Set the ID of this sensor for use in lambdas.
|
|
- All other options from :ref:`Sensor <config-sensor>`.
|
|
|
|
- **temperature** (**Required**): The information for the temperature sensor. Readings in degrees celsius (°C).
|
|
|
|
- **name** (**Required**, string): The name of the temperature sensor.
|
|
- **id** (*Optional*, :ref:`config-id`): Set the ID of this sensor for use in lambdas.
|
|
- All other options from :ref:`Sensor <config-sensor>`.
|
|
|
|
- **humidity** (**Required**): The information for the relative humidity sensor. Readings in %.
|
|
|
|
- **name** (**Required**, string): The name of the humidity sensor.
|
|
- **id** (*Optional*, :ref:`config-id`): Set the ID of this sensor for use in lambdas.
|
|
- All other options from :ref:`Sensor <config-sensor>`.
|
|
|
|
- **update_interval** (*Optional*, :ref:`config-time`): The interval to check the
|
|
sensor. Defaults to ``60s``.
|
|
|
|
- **uart_id** (*Optional*, :ref:`config-id`): Manually specify the ID of the :ref:`UART Component <uart>` if you want
|
|
to use multiple UART buses.
|
|
|
|
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID used for actions.
|
|
|
|
.. figure:: images/sm300d2-pins.jpg
|
|
:align: center
|
|
:width: 80.0%
|
|
|
|
Pins on the SM300D2. UART RX is not in use.
|
|
|
|
.. _pins-note:
|
|
|
|
.. note::
|
|
|
|
The board's ``GD`` pin must be connected to a ``GND`` pin on the ESP.
|
|
|
|
The sensor board requires between 4.8 and 5.2 volts via the ``5V`` pin in either the UART or RS485 socket, as they
|
|
are connected. If you're using a USB-powered ESP module with a 5V input pin (i.e. ``VIN``) exposed, you can choose
|
|
to connect the UART ``5V`` pin to the ESP's ``VIN`` and then power everything through either the LCD module or the
|
|
ESP module, with a single power cable. If you choose to power the ESP separately from the sensor board, leave the
|
|
UART ``5V`` pin unconnected.
|
|
|
|
|
|
See Also
|
|
--------
|
|
|
|
- :ref:`sensor-filters`
|
|
- :apiref:`sm300d2/sm300d2.h`
|
|
- :ghedit:`Edit`
|