mirror of
https://github.com/esphome/esphome-docs.git
synced 2024-11-16 10:55:21 +01:00
81 lines
3.1 KiB
ReStructuredText
81 lines
3.1 KiB
ReStructuredText
SDS011 Particulate Matter Sensor
|
|
================================
|
|
|
|
.. seo::
|
|
:description: Instructions for setting up SDS011 Particulate matter sensors
|
|
:image: sds011.jpg
|
|
:keywords: sds011
|
|
|
|
The ``sds011`` sensor platform allows you to use SDS011 particulate matter sensors (`datasheet <https://nettigo.pl/attachments/398>`__)
|
|
with ESPHome.
|
|
|
|
.. figure:: images/sds011-full.jpg
|
|
:align: center
|
|
:width: 50.0%
|
|
|
|
SDS011 Particulate Matter Sensor
|
|
|
|
As the communication with the SDS011 is done using UART, you need
|
|
to have an :ref:`UART bus <uart>` in your configuration with the ``rx_pin`` connected to the TX pin of the
|
|
SDS011 and optionally the ``tx_pin`` connected to the RX Pin of the SDS011 (it's switched because the
|
|
TX/RX labels are from the perspective of the individual device). Additionally, you need to set the baud rate to 9600.
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Example configuration entry
|
|
uart:
|
|
rx_pin: D0
|
|
tx_pin: D1
|
|
baud_rate: 9600
|
|
|
|
sensor:
|
|
- platform: sds011
|
|
pm_2_5:
|
|
name: "Particulate Matter <2.5µm Concentration"
|
|
pm_10_0:
|
|
name: "Particulate Matter <10.0µm Concentration"
|
|
update_interval: 5min
|
|
|
|
With ``update_interval``, the working period of the SDS011 device will be changed. If ``update_interval`` is
|
|
equal to ``0min``, the SDS011 will be set to continuous measurement and will report new measurement values
|
|
approximately every second.
|
|
|
|
If ``update_interval`` is between 1-30 minutes, the SDS011 periodically turns on for 30s before each measurement.
|
|
For the remaining time the sensor is shut off. As a result, this mode can reduce power consumption and increases
|
|
the lifetime of the SDS011.
|
|
|
|
Note that ``update_interval`` may not be set to ``never``.
|
|
|
|
Configuration variables:
|
|
------------------------
|
|
|
|
- **pm_2_5** (*Optional*): Use the concentration of particulates of size less than 2.5µm in µg per cubic meter.
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
|
|
- **pm_10_0** (*Optional*): Use the concentration of particulates of size less than 10.0µm in µg per cubic meter.
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
|
|
- **update_interval** (*Optional*, :ref:`config-time`): The interval to check the sensor in minutes.
|
|
This affects the working period of the SDS011 sensor. Defaults to ``0min``.
|
|
|
|
- **rx_only** (*Optional*, boolean): Whether the sensor is connected **only by RX pin** to the UART bus.
|
|
Since the SDS011 can not be configured in RX-only mode, ``update_interval`` has no effect and the sensor must be
|
|
configured separately. Defaults to ``false``.
|
|
|
|
- **uart_id** (*Optional*, :ref:`config-id`): Manually specify the ID of the :ref:`UART Component <uart>` if you want
|
|
to use multiple UART buses.
|
|
|
|
.. note::
|
|
|
|
The configuration variable ``update_interval`` reconfigure the SDS011 device. This setting is still effective
|
|
after power off. This can affect the performance of other libraries. Factory default is continuous measurement.
|
|
|
|
See Also
|
|
--------
|
|
|
|
- :doc:`/components/sensor/pmsx003`
|
|
- :ref:`sensor-filters`
|
|
- `Laser Dust Sensor Control Protocol <https://nettigo.pl/attachments/415>`__
|
|
- :apiref:`sds011/sds011.h`
|
|
- :ghedit:`Edit`
|