mirror of
https://github.com/esphome/esphome-docs.git
synced 2024-11-15 10:45:41 +01:00
298 lines
8.1 KiB
ReStructuredText
298 lines
8.1 KiB
ReStructuredText
Ethernet Component
|
|
==================
|
|
|
|
.. seo::
|
|
:description: Instructions for setting up the Ethernet configuration for your ESP32 node in ESPHome.
|
|
:image: ethernet.svg
|
|
:keywords: Ethernet, ESP32
|
|
|
|
This ESPHome component enables *wired* Ethernet connections for ESP32s.
|
|
|
|
Ethernet for ESP8266 is not supported.
|
|
|
|
This component and the Wi-Fi component may **not** be used simultaneously, even if both are physically available.
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Example configuration entry for RMII chips
|
|
ethernet:
|
|
type: LAN8720
|
|
mdc_pin: GPIOXX
|
|
mdio_pin: GPIOXX
|
|
clk_mode: GPIO0_IN
|
|
phy_addr: 0
|
|
|
|
# Optional manual IP
|
|
manual_ip:
|
|
static_ip: 10.0.0.42
|
|
gateway: 10.0.0.1
|
|
subnet: 255.255.255.0
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Example configuration entry for SPI chips
|
|
ethernet:
|
|
type: W5500
|
|
clk_pin: GPIOXX
|
|
mosi_pin: GPIOXX
|
|
miso_pin: GPIOXX
|
|
cs_pin: GPIOXX
|
|
interrupt_pin: GPIOXX
|
|
reset_pin: GPIOXX
|
|
|
|
Configuration variables:
|
|
------------------------
|
|
|
|
- **type** (**Required**, string): The type of LAN chipset/phy.
|
|
|
|
Supported chipsets are:
|
|
|
|
- ``LAN8720`` (RMII)
|
|
- ``RTL8201`` (RMII)
|
|
- ``DP83848`` (RMII)
|
|
- ``IP101`` (RMII)
|
|
- ``JL1101`` (RMII)
|
|
- ``KSZ8081`` (RMII)
|
|
- ``KSZ8081RNA`` (RMII)
|
|
- ``W5500`` (SPI)
|
|
|
|
RMII configuration variables:
|
|
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
- **mdc_pin** (**Required**, :ref:`config-pin`): The MDC pin of the board.
|
|
Usually this is ``GPIO23``.
|
|
- **mdio_pin** (**Required**, :ref:`config-pin`): The MDIO pin of the board.
|
|
Usually this is ``GPIO18``.
|
|
- **clk_mode** (*Optional*, string): The clock mode of the data lines. See your board's
|
|
datasheet for more details. Must be one of the following values:
|
|
|
|
- ``GPIO0_IN`` (Default) - External clock
|
|
- ``GPIO0_OUT`` - Internal clock
|
|
- ``GPIO16_OUT`` - Internal clock
|
|
- ``GPIO17_OUT`` - Internal clock
|
|
|
|
- **phy_addr** (*Optional*, int): The PHY addr type of the Ethernet controller. Defaults to 0.
|
|
- **phy_registers** (*Optional*, mapping): Arbitrary PHY register values to set after Ethernet initialization.
|
|
|
|
- **address** (**Required**, hex): The register address as a hex number (e.g. ``0x10`` for address 16)
|
|
- **value** (**Required**, hex): The value of the register to set as a hex number (e.g. ``0x1FFA``)
|
|
- **page_id** (*Optional*, hex): (RTL8201 only) Register page number to select before writing (e.g. ``0x07`` for page 7)
|
|
|
|
- **power_pin** (*Optional*, :ref:`Pin Schema <config-pin_schema>`): The pin controlling the
|
|
power/reset status of the Ethernet controller. Leave unspecified for no power pin (default).
|
|
|
|
SPI configuration variables:
|
|
^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
- **clk_pin** (**Required**, :ref:`config-pin`): The SPI clock pin.
|
|
- **mosi_pin** (**Required**, :ref:`config-pin`): The SPI MOSI pin.
|
|
- **miso_pin** (**Required**, :ref:`config-pin`): The SPI MISO pin.
|
|
- **cs_pin** (**Required**, :ref:`config-pin`): The SPI chip select pin.
|
|
- **interrupt_pin** (*Optional*, :ref:`config-pin`): The interrupt pin.
|
|
- **reset_pin** (*Optional*, :ref:`config-pin`): The reset pin.
|
|
- **clock_speed** (*Optional*, float): The SPI clock speed.
|
|
Any frequency between `8Mhz` and `80Mhz` is allowed, but the nearest integer division
|
|
of `80Mhz` is used, i.e. `16Mhz` (`80Mhz` / 5) is used when `15Mhz` is configured.
|
|
Default: `26.67Mhz`.
|
|
|
|
Advanced common configuration variables:
|
|
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
- **manual_ip** (*Optional*): Manually configure the static IP of the node.
|
|
|
|
- **static_ip** (**Required**, IPv4 address): The static IP of your node.
|
|
- **gateway** (**Required**, IPv4 address): The gateway of the local network.
|
|
- **subnet** (**Required**, IPv4 address): The subnet of the local network.
|
|
- **dns1** (*Optional*, IPv4 address): The main DNS server to use.
|
|
- **dns2** (*Optional*, IPv4 address): The backup DNS server to use.
|
|
|
|
- **use_address** (*Optional*, string): Manually override what address to use to connect
|
|
to the ESP. Defaults to auto-generated value. For example, if you have changed your
|
|
static IP and want to flash OTA to the previously configured IP address.
|
|
- **domain** (*Optional*, string): Set the domain of the node hostname used for uploading.
|
|
For example, if it's set to ``.local``, all uploads will be sent to ``<HOSTNAME>.local``.
|
|
Defaults to ``.local``.
|
|
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID used for code generation.
|
|
|
|
|
|
.. note::
|
|
|
|
If your Ethernet board is not designed with an ESP32 built in, it's common to attempt
|
|
to use flying leads, dupont wires, etc. to connect the Ethernet controller to the ESP32.
|
|
This approach is likely to fail, however, as the Ethernet interface uses a high frequency
|
|
clock signal that will not travel reliably over these types of connections. For more
|
|
information and wiring details refer to the link in the *See also* section.
|
|
|
|
.. note::
|
|
|
|
SPI based chips do *not* use :doc:`spi`. This means that SPI pins can't be shared with other devices.
|
|
|
|
Configuration examples
|
|
----------------------
|
|
|
|
**Olimex ESP32-POE**:
|
|
|
|
.. code-block:: yaml
|
|
|
|
ethernet:
|
|
type: LAN8720
|
|
mdc_pin: GPIO23
|
|
mdio_pin: GPIO18
|
|
clk_mode: GPIO17_OUT
|
|
phy_addr: 0
|
|
power_pin: GPIO12
|
|
|
|
.. note::
|
|
|
|
WROVER version of Olimex POE cards change CLK to ping GPIO0, configuration must be `clk_mode: GPIO0_OUT`.
|
|
|
|
|
|
**Olimex ESP32-EVB**:
|
|
|
|
.. code-block:: yaml
|
|
|
|
ethernet:
|
|
type: LAN8720
|
|
mdc_pin: GPIO23
|
|
mdio_pin: GPIO18
|
|
clk_mode: GPIO0_IN
|
|
phy_addr: 0
|
|
|
|
**Olimex ESP32-GATEWAY** and **LILYGO TTGO T-Internet-POE ESP32-WROOM LAN8270A**:
|
|
|
|
.. code-block:: yaml
|
|
|
|
ethernet:
|
|
type: LAN8720
|
|
mdc_pin: GPIO23
|
|
mdio_pin: GPIO18
|
|
clk_mode: GPIO17_OUT
|
|
phy_addr: 0
|
|
|
|
**LILYGO TTGO T-Internet ESP32-WROVER-E LAN8270**:
|
|
|
|
.. code-block:: yaml
|
|
|
|
ethernet:
|
|
type: LAN8720
|
|
mdc_pin: GPIO23
|
|
mdio_pin: GPIO18
|
|
clk_mode: GPIO0_OUT
|
|
phy_addr: 0
|
|
power_pin: GPIO04
|
|
|
|
**Wireless Tag WT32-ETH01** and **SMLIGHT SLZB-06 PoE Zigbee**:
|
|
|
|
.. code-block:: yaml
|
|
|
|
ethernet:
|
|
type: LAN8720
|
|
mdc_pin: GPIO23
|
|
mdio_pin: GPIO18
|
|
clk_mode: GPIO0_IN
|
|
phy_addr: 1
|
|
power_pin: GPIO16
|
|
|
|
**M5Stack PoESP32** and **ESP32-Ethernet-Kit**:
|
|
|
|
.. code-block:: yaml
|
|
|
|
ethernet:
|
|
type: IP101
|
|
mdc_pin: GPIO23
|
|
mdio_pin: GPIO18
|
|
clk_mode: GPIO0_IN
|
|
phy_addr: 1
|
|
power_pin: GPIO5
|
|
|
|
**AiThinker ESP32-G Gateway**:
|
|
|
|
.. code-block:: yaml
|
|
|
|
ethernet:
|
|
type: LAN8720
|
|
mdc_pin: GPIO23
|
|
mdio_pin: GPIO18
|
|
clk_mode: GPIO17_OUT
|
|
phy_addr: 1
|
|
power_pin: GPIO5
|
|
|
|
**wESP32**:
|
|
|
|
.. code-block:: yaml
|
|
|
|
# for board up to rev.5
|
|
ethernet:
|
|
type: LAN8720
|
|
mdc_pin: GPIO16
|
|
mdio_pin: GPIO17
|
|
clk_mode: GPIO0_IN
|
|
phy_addr: 0
|
|
|
|
# for board rev.7 and up
|
|
ethernet:
|
|
type: RTL8201
|
|
mdc_pin: GPIO16
|
|
mdio_pin: GPIO17
|
|
clk_mode: GPIO0_IN
|
|
phy_addr: 0
|
|
phy_registers:
|
|
- address: 0x10
|
|
value: 0x1FFA
|
|
page_id: 0x07
|
|
|
|
|
|
.. note::
|
|
|
|
Revision 5 and below of the wESP32 board use the LAN8720 Ethernet PHY. Revision 7 and newer of it use the RTL8201 Ethernet PHY.
|
|
|
|
|
|
**OpenHacks LAN8720**:
|
|
|
|
.. code-block:: yaml
|
|
|
|
ethernet:
|
|
type: LAN8720
|
|
mdc_pin: GPIO23
|
|
mdio_pin: GPIO18
|
|
phy_addr: 1
|
|
|
|
.. note::
|
|
|
|
This board has an issue that might cause the ESP32 to boot in program mode. When testing, make sure
|
|
you are monitoring the serial output and reboot the device several times to see if it boots into the
|
|
program properly.
|
|
|
|
|
|
**Esp32-Stick-Eth** and **Esp32-Stick-PoE-P** and **Esp32-Stick-PoE-A**:
|
|
|
|
.. code-block:: yaml
|
|
|
|
ethernet:
|
|
type: LAN8720
|
|
mdc_pin: GPIO23
|
|
mdio_pin: GPIO18
|
|
clk_mode: GPIO17_OUT
|
|
phy_addr: 1
|
|
|
|
**LILYGO T-ETH-Lite ESP32**:
|
|
|
|
.. code-block:: yaml
|
|
|
|
ethernet:
|
|
type: RTL8201
|
|
mdc_pin: GPIO23
|
|
mdio_pin: GPIO18
|
|
clk_mode: GPIO0_IN
|
|
phy_addr: 0
|
|
power_pin: GPIO12
|
|
|
|
See Also
|
|
--------
|
|
|
|
- :doc:`network`
|
|
- :doc:`text_sensor/ethernet_info`
|
|
- :apiref:`ethernet/ethernet_component.h`
|
|
- `ESP32 Ethernet PHY connection info <https://pcbartists.com/design/embedded/esp32-ethernet-phy-schematic-design/>`__
|
|
- :ghedit:`Edit`
|