mirror of
https://github.com/esphome/esphome-docs.git
synced 2024-11-05 09:20:08 +01:00
127 lines
3.4 KiB
ReStructuredText
127 lines
3.4 KiB
ReStructuredText
H801 RGBW LED controller
|
|
========================
|
|
|
|
The H801 is pretty affordable and easy to hack and adapt to your needs. It can be found on `AliExpress <https://s.click.aliexpress.com/e/bbnUDBZW>`__
|
|
`Here <http://tinkerman.cat/closer-look-h801-led-wifi-controller/>`__ is an article about the
|
|
hardware for those who have an interest for more details about the board.
|
|
It can be used as a RGB, RGBW, RGB dual white or even control 5 individual monochromatic strips if you want or combinations of these.
|
|
|
|
.. figure:: images/h801.jpg
|
|
:align: center
|
|
:width: 80.0%
|
|
|
|
For ESPHome, you can then use the :doc:`RGBW </components/light/rgbw>`
|
|
and the :doc:`ESP8266 Software PWM output </components/output/esp8266_pwm>` components using below configuration:
|
|
|
|
.. code-block:: yaml
|
|
|
|
esphome:
|
|
name: h801light
|
|
platform: ESP8266
|
|
board: esp01_1m
|
|
wifi:
|
|
ssid: 'WIFI'
|
|
password: 'WIFIPASS'
|
|
manual_ip:
|
|
static_ip: x.x.x.x
|
|
gateway: x.x.x.x
|
|
subnet: 255.255.255.0
|
|
logger:
|
|
api:
|
|
ota:
|
|
sensor:
|
|
- platform: wifi_signal
|
|
name: "WiFi Signal h801light"
|
|
update_interval: 60s
|
|
#RGBWarm
|
|
output:
|
|
- platform: esp8266_pwm
|
|
pin: 12
|
|
frequency: 1000 Hz
|
|
id: pwm_b
|
|
- platform: esp8266_pwm
|
|
pin: 13
|
|
frequency: 1000 Hz
|
|
id: pwm_g
|
|
- platform: esp8266_pwm
|
|
pin: 15
|
|
frequency: 1000 Hz
|
|
id: pwm_r
|
|
- platform: esp8266_pwm
|
|
pin: 14
|
|
frequency: 1000 Hz
|
|
id: pwm_w
|
|
light:
|
|
- platform: rgbw
|
|
name: "H801 Light"
|
|
red: pwm_r
|
|
green: pwm_g
|
|
blue: pwm_b
|
|
white: pwm_w
|
|
|
|
|
|
Make your node in the ESPHome dashboard and compile/upload it.
|
|
(if it fails OTA it must be uploaded manually with your favorite ESP flasher,
|
|
e.g. :ref:`esphome-flasher <esphome-flasher>`)
|
|
|
|
.. figure:: images/gpio.jpg
|
|
:align: center
|
|
:width: 80.0%
|
|
|
|
Front side of board with pins soldered on
|
|
|
|
.. figure:: images/back.jpg
|
|
:align: center
|
|
:width: 80.0%
|
|
|
|
Back side of the board (don't melt the blue and red wire when soldering)
|
|
|
|
.. figure:: images/rgbwarm.jpg
|
|
:align: center
|
|
:width: 80.0%
|
|
|
|
This LED strip can be used with the sketch as-is
|
|
|
|
.. figure:: images/rgbw.jpg
|
|
:align: center
|
|
:width: 80.0%
|
|
|
|
For this type of led strip you have to swap the white and blue GPIO numbers in the sketch.
|
|
|
|
You will need to solder pins to the board inside the H801 (fortunately it's pretty roomy and
|
|
not a lot of components or stuff in the way apart from the 2 wires on the back).
|
|
|
|
3.3V, GND, TX and RX (RX to RX and TX to TX) needs to be connected to your serial adapter, the
|
|
two other pins must be shorted throughout the flashing process by a jumper or a breadboard cable.
|
|
(Remember to remove it after flashing)
|
|
|
|
Add A PIR(Motion) Sensor
|
|
------------------------
|
|
|
|
It's possible to use the header that was soldered on for flashing as an input.
|
|
The example below uses the TX pin as a PIR motion sensor input:
|
|
|
|
.. figure:: images/h801-pir_sensor.jpg
|
|
:align: center
|
|
:width: 80.0%
|
|
|
|
H801 shown with PIR connedted to header pins
|
|
|
|
The following can be appended to the YAML file for your H801 to configure the TX pin as a motion
|
|
sensor input.
|
|
|
|
.. code-block:: yaml
|
|
|
|
binary_sensor:
|
|
- platform: gpio
|
|
pin: GPIO3
|
|
name: "GPIO3-TX Motion"
|
|
device_class: motion
|
|
|
|
See Also
|
|
--------
|
|
|
|
- :doc:`/components/light/rgbw`
|
|
- :doc:`/components/output/esp8266_pwm`
|
|
- :ghedit:`Edit`
|