mirror of
https://github.com/esphome/esphome-docs.git
synced 2024-11-06 09:31:39 +01:00
82 lines
2.7 KiB
ReStructuredText
82 lines
2.7 KiB
ReStructuredText
SMT100 Soil Moisture Sensor
|
|
================================
|
|
|
|
.. seo::
|
|
:description: Instructions for setting up SMT100 soil moisture and temperature sensor
|
|
:image: smt100.jpg
|
|
:keywords: smt100
|
|
|
|
|
|
The SMT100 sensor platform allows you to use the SMT100 soil moisture and temperature with ESPHome.
|
|
|
|
.. figure:: images/smt100.jpg
|
|
:align: center
|
|
:width: 50.0%
|
|
|
|
|
|
The communication with this integration is done over a UART bus using a simple ASCII protocol. You must therefore have a ``uart:`` entry in your configuration with both the TX and RX pins set to some pins on your board and the baud rate set to 9600.
|
|
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Example configuration entry
|
|
uart:
|
|
tx_pin: TX
|
|
rx_pin: RX
|
|
baud_rate: 9600
|
|
|
|
sensor:
|
|
- platform: smt100
|
|
counts:
|
|
name: "Counts"
|
|
permittivity:
|
|
name: "Permittivity"
|
|
temperature:
|
|
name: "Temperature"
|
|
moisture:
|
|
name: "Moisture"
|
|
voltage:
|
|
name: "Voltage"
|
|
|
|
|
|
Configuration variables:
|
|
------------------------
|
|
|
|
- **counts** (*Optional*): Raw measurement data from the sensor electronics (dimensionless quantity). Higher counts mean less moisture. May be used for material specific calibrations.
|
|
|
|
- **name** (**Required**): Sensor name.
|
|
- All other options from :ref:`Sensor <config-sensor>`.
|
|
|
|
- **dielectric_constant** (*Optional*): Dielectric coefficient or permittivity of the material to be measured (dimensionless quantity). Higher permittivity means higher water content. May be used for material specific calibration.
|
|
|
|
- **name** (**Required**): Sensor name.
|
|
- All other options from :ref:`Sensor <config-sensor>`.
|
|
|
|
- **temperature** (*Optional*): Soil temperature in degrees Celsius. Please note that the temperature sensor is inside the black sensor enclosure and requires some time to equilibrate with the soil temperature.
|
|
|
|
- **name** (**Required**): Sensor name.
|
|
- All other options from :ref:`Sensor <config-sensor>`.
|
|
|
|
- **moisture** (*Optional*): Soil moisture (volumetric water content in %).
|
|
|
|
- **name** (**Required**): Sensor name.
|
|
- All other options from :ref:`Sensor <config-sensor>`.
|
|
|
|
- **voltage** (*Optional*): Supply voltage of the sensor in Volt.
|
|
|
|
- **name** (**Required**): Sensor name.
|
|
- All other options from :ref:`Sensor <config-sensor>`.
|
|
|
|
- **uart_id** (*Optional*, :ref:`config-id`): Manually specify the ID of the :ref:`UART Component <uart>` if you want
|
|
to use multiple UART buses.
|
|
|
|
- **update_interval** (*Optional*, :ref:`config-time`): The interval to pull the sensor. Defaults is 60s.
|
|
|
|
See Also
|
|
--------
|
|
|
|
- :doc:`/components/sensor/smt100`
|
|
- :ref:`sensor-filters`
|
|
- :apiref:`smt100/smt100.h`
|
|
- :ghedit:`Edit`
|