mirror of
https://github.com/esphome/esphome-docs.git
synced 2024-11-18 11:15:36 +01:00
88e315e0e4
* Many example yaml tidy-ups * Update components/sensor/hlw8012.rst --------- Co-authored-by: Keith Burzinski <kbx81x@gmail.com>
117 lines
4.9 KiB
ReStructuredText
117 lines
4.9 KiB
ReStructuredText
Pulse Meter Sensor
|
||
==================
|
||
|
||
.. seo::
|
||
:description: Instructions for setting up pulse meter sensors.
|
||
:image: pulse.svg
|
||
|
||
The pulse meter sensor allows you to count the number and frequency of pulses on any pin. It is intended to be a drop-in replacement
|
||
for the :doc:`pulse counter component </components/sensor/pulse_counter>`.
|
||
Rather than counting pulses over a fixed time interval, the pulse meter sensor measures the time between pulses. The precise manner in which this is done depends on the ``internal_filter_mode`` option. This leads to a higher resolution, especially for low pulse rates, as the pulse counter sensor is limited by the number of pulses within a time interval.
|
||
|
||
Here's a comparison of the two sensors. The pulse meter is the smoother line. Both are set to an update interval of 10 seconds (using the ``update_interval`` and the ``throttle_average`` option respectively):
|
||
|
||
.. figure:: /images/pulse-counter_vs_pulse-meter.png
|
||
:align: center
|
||
:width: 50.0%
|
||
|
||
Please note that it is not possible to use both of these two sensors on the same pin at the same time.
|
||
|
||
.. code-block:: yaml
|
||
|
||
# Example configuration entry
|
||
sensor:
|
||
- platform: pulse_meter
|
||
pin: GPIOXX
|
||
name: "Pulse Meter"
|
||
|
||
Configuration variables
|
||
------------------------
|
||
|
||
- **pin** (**Required**, :ref:`config-pin`): The pin to count pulses on.
|
||
- **name** (**Required**, string): The name of the sensor.
|
||
|
||
- **internal_filter** (*Optional*, :ref:`config-time`): If a pulse shorter than this time is detected, it is discarded. Defaults to ``13us``.
|
||
|
||
This acts as a debounce filter to eliminate input noise, so choose a value a little less than your expected minimum pulse width.
|
||
|
||
- **internal_filter_mode** (*Optional*, string): Determines how the internal filter is applied.
|
||
One of ``EDGE`` or ``PULSE``. Defaults to ``EDGE``.
|
||
- In ``EDGE`` mode, subsequent rising edges are compared and if they fall into an interval lesser than the ``internal filter`` value, the last one is discarded. This is useful if your input signal bounces, but is otherwise clean.
|
||
- In ``PULSE`` mode, the rising edge is discarded if any further interrupts are detected before the ``internal_filter`` time has passed. In other words, a high pulse must be at least ``internal_filter`` long to be counted. This is useful if you have a noisy input signal that may have bounces before and/or after the main pulse.
|
||
|
||
- **timeout** (*Optional*, :ref:`config-time`): If we don't see a pulse for this length of time, we assume *0 pulses/s*. Defaults to ``5 min``.
|
||
- **total** (*Optional*, :ref:`config-id`): An additional sensor that outputs the total number of pulses counted.
|
||
- All other options from :ref:`Sensor <config-sensor>`.
|
||
|
||
Converting units
|
||
----------------
|
||
|
||
The sensor defaults to units of *pulses/min*, You can change this by using :ref:`sensor-filters`.
|
||
For example, if you’re using the pulse meter with a photodiode to count the light pulses on a power meter that has an impulse constant of *10000 pulses / kWh*, you can use the following to output instantaneous usage in *W*:
|
||
|
||
.. code-block:: yaml
|
||
|
||
# Example configuration entry
|
||
sensor:
|
||
- platform: pulse_meter
|
||
name: 'Electricity Usage'
|
||
id: sensor_pulse_meter # Optional ID, necessary if you want to calculate the total number of pulses.
|
||
unit_of_measurement: 'W'
|
||
device_class: power
|
||
state_class: measurement
|
||
internal_filter: 20ms # Assuming maximum load of 16 kW and 10000 impulses per kWh, any pulses faster than 22.5 ms would exceed load. -10% ~= 20 ms.
|
||
accuracy_decimals: 0
|
||
pin: GPIOXX
|
||
filters:
|
||
- multiply: 6 # (60s / impulse constant) * (1000W / 1kW)
|
||
|
||
Counting total pulses
|
||
---------------------
|
||
|
||
When the total sensor is configured, ``pulse_meter`` also reports the total
|
||
number of pulses measured.
|
||
|
||
.. code-block:: yaml
|
||
|
||
# Example configuration entry
|
||
sensor:
|
||
- platform: pulse_meter
|
||
# ...
|
||
total:
|
||
name: "Total Pulses"
|
||
|
||
(Re)Setting the total pulse count
|
||
---------------------------------
|
||
|
||
Using this action, you are able to reset/set the total pulse count. This can be useful
|
||
if you would like the ``total`` sensor to match what you see on your meter you are
|
||
trying to match.
|
||
|
||
.. code-block:: yaml
|
||
|
||
api:
|
||
services:
|
||
- service: set_total
|
||
variables:
|
||
new_total: int
|
||
then:
|
||
- pulse_meter.set_total_pulses:
|
||
id: sensor_pulse_meter
|
||
value: !lambda 'return new_total;'
|
||
|
||
.. note::
|
||
|
||
This value is the raw count of pulses, and not the value you see after the filters
|
||
|
||
See Also
|
||
--------
|
||
|
||
- :ref:`sensor-filters`
|
||
- :doc:`/components/sensor/pulse_counter`
|
||
- :doc:`/components/sensor/total_daily_energy`
|
||
- :doc:`/cookbook/power_meter`
|
||
- `Home Assistant Glow 🌟 <https://github.com/klaasnicolaas/home-assistant-glow/>`__.
|
||
- :apiref:`pulse_meter/pulse_meter_sensor.h`
|
||
- :ghedit:`Edit`
|