mirror of
https://github.com/esphome/esphome-docs.git
synced 2024-11-16 10:55:21 +01:00
339 lines
10 KiB
ReStructuredText
339 lines
10 KiB
ReStructuredText
Stepper Component
|
|
=================
|
|
|
|
.. seo::
|
|
:description: Instructions for setting up stepper motor drivers in ESPHome
|
|
:image: folder-open.svg
|
|
:keywords: stepper motor, stepper driver, a4988
|
|
|
|
The ``stepper`` component allows you to use stepper motors with ESPHome.
|
|
Currently only the A4988 stepper driver
|
|
(`datasheet <https://www.pololu.com/file/0J450/a4988_DMOS_microstepping_driver_with_translator.pdf>`__)
|
|
and ULN2003 (`datasheet <http://www.ti.com/lit/ds/symlink/uln2003a.pdf>`__) are supported.
|
|
|
|
.. note::
|
|
|
|
This component will not show up in the Home Assistant front-end automatically because
|
|
Home Assistant doesn't have support for steppers. Please see :ref:`stepper-ha-config`.
|
|
|
|
.. _base_stepper_config:
|
|
|
|
Base Stepper Configuration
|
|
--------------------------
|
|
|
|
All stepper configuration schemas inherit these options.
|
|
|
|
Configuration variables:
|
|
|
|
- **max_speed** (**Required**, float): The maximum speed in ``steps/s`` (steps per seconds) to drive the
|
|
stepper at. Note most steppers can't step properly with speeds higher than 250 steps/s.
|
|
- **acceleration** (*Optional*, float): The acceleration in ``steps/s^2`` (steps per seconds squared)
|
|
to use when starting to move. The default is ``inf`` which means infinite acceleration, so the
|
|
stepper will try to drive with the full speed immediately. This value is helpful if that first motion of
|
|
the motor is too jerky for what it's moving. If you make this a small number, it will take the motor a
|
|
moment to get up to speed.
|
|
- **deceleration** (*Optional*, float): The same as ``acceleration``, but for when the motor is decelerating
|
|
shortly before reaching the set position. Defaults to ``inf`` (immediate deceleration).
|
|
|
|
A4988 Component
|
|
---------------
|
|
|
|
Put this code into the configuration file on ESPHome for this device.
|
|
|
|
.. code-block:: yaml
|
|
|
|
stepper:
|
|
- platform: a4988
|
|
id: my_stepper
|
|
step_pin: D0
|
|
dir_pin: D1
|
|
max_speed: 250 steps/s
|
|
|
|
# Optional:
|
|
sleep_pin: D2
|
|
acceleration: inf
|
|
deceleration: inf
|
|
|
|
|
|
Configuration variables:
|
|
|
|
- **id** (**Required**, :ref:`config-id`): Specify the ID of the stepper so that you can control it.
|
|
- **step_pin** (**Required**, :ref:`Pin Schema <config-pin_schema>`): The ``STEP`` pin of the A4988
|
|
stepper driver.
|
|
- **dir_pin** (**Required**, :ref:`Pin Schema <config-pin_schema>`): The ``DIRECTION`` pin of the A4988
|
|
stepper driver.
|
|
- **sleep_pin** (*Optional*, :ref:`Pin Schema <config-pin_schema>`): Optionally also use the ``SLEEP`` pin
|
|
of the A4988 stepper driver. If specified, the driver will be put into sleep mode as soon as the stepper
|
|
reaches the target steps.
|
|
|
|
- All other from :ref:`base_stepper_config`.
|
|
|
|
.. note::
|
|
|
|
If the stepper is driving in the wrong direction, you can invert the ``dir_pin``:
|
|
|
|
.. code-block:: yaml
|
|
|
|
stepper:
|
|
- platform: a4988
|
|
# ...
|
|
dir_pin:
|
|
number: D1
|
|
inverted: true
|
|
|
|
ULN2003 Component
|
|
-----------------
|
|
|
|
Put this code into the configuration file on ESPHome for this device.
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Example configuration entry
|
|
stepper:
|
|
- platform: uln2003
|
|
id: my_stepper
|
|
pin_a: D0
|
|
pin_b: D1
|
|
pin_c: D2
|
|
pin_d: D3
|
|
max_speed: 250 steps/s
|
|
|
|
# Optional:
|
|
acceleration: inf
|
|
deceleration: inf
|
|
|
|
|
|
Configuration variables:
|
|
|
|
- **id** (**Required**, :ref:`config-id`): Specify the ID of the stepper so that you can control it.
|
|
- **pin_a** (**Required**, :ref:`Pin Schema <config-pin_schema>`): The pin **a** of the stepper control board.
|
|
- **pin_b** (**Required**, :ref:`Pin Schema <config-pin_schema>`): The pin **b** of the stepper control board.
|
|
- **pin_c** (**Required**, :ref:`Pin Schema <config-pin_schema>`): The pin **c** of the stepper control board.
|
|
- **pin_d** (**Required**, :ref:`Pin Schema <config-pin_schema>`): The pin **d** of the stepper control board.
|
|
- **sleep_when_done** (*Optional*, boolean): Whether to turn off all coils when the stepper has
|
|
reached the target position
|
|
- **step_mode** (*Optional*, string): The step mode to operate the motor with. One of:
|
|
|
|
- ``FULL_STEP`` (Default)
|
|
- ``HALF_STEP``
|
|
- ``WAVE_DRIVE``
|
|
|
|
- All other from :ref:`base_stepper_config`.
|
|
|
|
.. _stepper-set_target_action:
|
|
|
|
``stepper.set_target`` Action
|
|
-----------------------------
|
|
|
|
To use your stepper motor in :ref:`automations <automation>` or templates, you can use this action to set the target
|
|
position (in steps). The stepper will always run towards the target position and stop once it has reached the target.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
then:
|
|
- stepper.set_target:
|
|
id: my_stepper
|
|
target: 250
|
|
|
|
# Templated
|
|
- stepper.set_target:
|
|
id: my_stepper
|
|
target: !lambda |-
|
|
if (id(my_binary_sensor).state) {
|
|
return 1000;
|
|
} else {
|
|
return -1000;
|
|
}
|
|
|
|
Configuration options:
|
|
|
|
- **id** (**Required**, :ref:`config-id`): The ID of the stepper.
|
|
- **target** (**Required**, int, :ref:`templatable <config-templatable>`): The target position in steps.
|
|
|
|
.. warning::
|
|
|
|
This turns the stepper to an absolute position! To have the servo move *relative* to the current
|
|
position, first reset the current position and then set the target to the relative value.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
then:
|
|
# Move 150 steps forward
|
|
- stepper.report_position:
|
|
id: my_stepper
|
|
position: 0
|
|
- stepper.set_target:
|
|
id: my_stepper
|
|
target: 150
|
|
|
|
.. _stepper-report_position_action:
|
|
|
|
``stepper.report_position`` Action
|
|
----------------------------------
|
|
|
|
All steppers start out with a target and current position of ``0`` on boot. However, if you for example want to home
|
|
a stepper motor, it can be useful to **report** the stepper where it is currently at.
|
|
|
|
With this action, you can set the stepper's internal position counter to a specific value (in steps). Please note
|
|
that reporting the position can create unexpected moves of the stepper. For example, if the stepper's target and
|
|
current position is at 1000 steps and you "report" a position of 0, the stepper will move 1000 steps forward to match
|
|
the target again.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
then:
|
|
- stepper.report_position:
|
|
id: my_stepper
|
|
position: 250
|
|
# It's best to call set_target directly after report_position, so that the stepper doesn't move
|
|
- stepper.set_target:
|
|
id: my_stepper
|
|
target: 250
|
|
|
|
# Templated
|
|
- stepper.report_position:
|
|
id: my_stepper
|
|
position: !lambda |-
|
|
if (id(my_binary_sensor).state) {
|
|
return 0;
|
|
} else {
|
|
return -1000;
|
|
}
|
|
|
|
Configuration variables:
|
|
|
|
- **id** (**Required**, :ref:`config-id`): The ID of the stepper.
|
|
- **position** (**Required**, int, :ref:`templatable <config-templatable>`): The position to report in steps.
|
|
|
|
.. _stepper-set_speed_action:
|
|
|
|
``stepper.set_speed`` Action
|
|
----------------------------
|
|
|
|
This :ref:`Action <config-action>` allows you to set the speed of a stepper at runtime.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
- stepper.set_speed:
|
|
id: my_stepper
|
|
speed: 250 steps/s
|
|
|
|
Configuration variables:
|
|
|
|
- **id** (**Required**, :ref:`config-id`): The ID of the stepper.
|
|
- **speed** (**Required**, :ref:`templatable <config-templatable>`, float): The speed
|
|
in ``steps/s`` (steps per seconds) to drive the stepper at.
|
|
|
|
.. _stepper-set_acceleration_action:
|
|
|
|
``stepper.set_acceleration`` Action
|
|
-----------------------------------
|
|
|
|
This :ref:`Action <config-action>` allows you to set the acceleration of a stepper at runtime.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
- stepper.set_acceleration:
|
|
id: my_stepper
|
|
acceleration: 250 steps/s^2
|
|
|
|
Configuration variables:
|
|
|
|
- **id** (**Required**, :ref:`config-id`): The ID of the stepper.
|
|
- **acceleration** (**Required**, :ref:`templatable <config-templatable>`, float): The acceleration
|
|
in ``steps/s^2`` (steps per seconds squared) to use when starting to move.
|
|
|
|
.. _stepper-set_deceleration_action:
|
|
|
|
``stepper.set_deceleration`` Action
|
|
-----------------------------------
|
|
|
|
This :ref:`Action <config-action>` allows you to set the deceleration of a stepper at runtime.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
- stepper.set_deceleration:
|
|
id: my_stepper
|
|
deceleration: 250 steps/s^2
|
|
|
|
Configuration variables:
|
|
|
|
- **id** (**Required**, :ref:`config-id`): The ID of the stepper.
|
|
- **deceleration** (**Required**, :ref:`templatable <config-templatable>`, float): The same as ``acceleration``,
|
|
but for when the motor is decelerating shortly before reaching the set position.
|
|
|
|
.. _stepper-ha-config:
|
|
|
|
Home Assistant Configuration
|
|
----------------------------
|
|
|
|
The easiest way to control your stepper from Home Assistant is to add a ``number`` to your ESPHome
|
|
configuration. See :ref:`Number <config-number>` for more information.
|
|
|
|
.. code-block:: yaml
|
|
|
|
number:
|
|
- platform: template
|
|
name: Stepper Control
|
|
min_value: -100
|
|
max_value: 100
|
|
step: 1
|
|
set_action:
|
|
then:
|
|
- stepper.set_target:
|
|
id: my_stepper
|
|
target: !lambda 'return x;'
|
|
|
|
stepper:
|
|
- platform: ...
|
|
# [...] stepper config
|
|
id: my_stepper
|
|
|
|
.. _stepper-lambda_calls:
|
|
|
|
lambda calls
|
|
------------
|
|
|
|
From :ref:`lambdas <config-lambda>`, you can call several methods on stepper motors to do some
|
|
advanced stuff (see the full API Reference for more info).
|
|
|
|
- ``set_target``: Set the target position of the motor as an integer.
|
|
|
|
.. code-block:: cpp
|
|
|
|
// Argument is integer (signed int)
|
|
// Set the (absolute) target position to 250 steps
|
|
id(my_stepper).set_target(250);
|
|
|
|
- ``report_position``: Report the current position as an integer.
|
|
|
|
.. code-block:: cpp
|
|
|
|
// Report the (absolute) current position as 250 steps
|
|
id(my_stepper).report_position(250);
|
|
|
|
- ``current_position``: Get the current position of the stepper as an integer.
|
|
|
|
.. code-block:: cpp
|
|
|
|
int pos = id(my_stepper).current_position;
|
|
|
|
|
|
- ``target_position``: Get the set target position of the stepper as an integer.
|
|
|
|
.. code-block:: cpp
|
|
|
|
int pos = id(my_stepper).target_position;
|
|
|
|
See Also
|
|
--------
|
|
|
|
- :apiref:`stepper/stepper.h`
|
|
- :ghedit:`Edit`
|