mirror of
https://github.com/esphome/esphome-docs.git
synced 2024-09-07 01:08:15 +02:00
379 lines
20 KiB
ReStructuredText
379 lines
20 KiB
ReStructuredText
Remote Receiver
|
|
===============
|
|
|
|
.. seo::
|
|
:description: Instructions for setting up remote receiver binary sensors for infrared and RF codes.
|
|
:image: remote.svg
|
|
:keywords: RF, infrared
|
|
|
|
The ``remote_receiver`` component lets you receive and decode any remote signal, these can
|
|
for example be infrared remotes or 433MHz signals.
|
|
|
|
The component is split up into two parts: the remote receiver hub which
|
|
handles setting the pin and some other settings, and individual
|
|
:ref:`remote receiver binary sensors <remote-receiver-binary-sensor>`
|
|
which will trigger when they hear their own configured signal.
|
|
|
|
**See** :ref:`remote-setting-up-infrared` **and** :ref:`remote-setting-up-rf` **for set up guides.**
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Example configuration entry
|
|
remote_receiver:
|
|
pin: GPIO32
|
|
dump: all
|
|
|
|
Configuration variables:
|
|
------------------------
|
|
|
|
- **pin** (**Required**, :ref:`config-pin`): The pin to receive the remote signal on.
|
|
- **dump** (*Optional*, list): Decode and dump these remote codes in the logs (at log.level=DEBUG).
|
|
Set to ``all`` to dump all available codecs:
|
|
|
|
- **aeha**: Decode and dump AEHA infrared codes.
|
|
- **canalsat**: Decode and dump CanalSat infrared codes.
|
|
- **canalsatld**: Decode and dump CanalSatLD infrared codes.
|
|
- **coolix**: Decode and dump Coolix infrared codes.
|
|
- **dish**: Decode and dump Dish infrared codes.
|
|
- **jvc**: Decode and dump JVC infrared codes.
|
|
- **lg**: Decode and dump LG infrared codes.
|
|
- **magiquest**: Decode and dump MagiQuest wand infrared codes.
|
|
- **midea**: Decode and dump Midea infrared codes.
|
|
- **nec**: Decode and dump NEC infrared codes.
|
|
- **nexa**: Decode and dump Nexa (RF) codes.
|
|
- **panasonic**: Decode and dump Panasonic infrared codes.
|
|
- **pioneer**: Decode and dump Pioneer infrared codes.
|
|
- **pronto**: Print remote code in Pronto form. Useful for using arbitrary protocols.
|
|
- **raw**: Print all remote codes in their raw form. Also useful for using arbitrary protocols.
|
|
- **rc5**: Decode and dump RC5 IR codes.
|
|
- **rc6**: Decode and dump RC6 IR codes.
|
|
- **rc_switch**: Decode and dump RCSwitch RF codes.
|
|
- **samsung**: Decode and dump Samsung infrared codes.
|
|
- **samsung36**: Decode and dump Samsung36 infrared codes.
|
|
- **sony**: Decode and dump Sony infrared codes.
|
|
- **toshiba_ac**: Decode and dump Toshiba AC infrared codes.
|
|
|
|
- **tolerance** (*Optional*, int): The percentage that the remote signal lengths can deviate in the
|
|
decoding process. Defaults to ``25%``.
|
|
- **buffer_size** (*Optional*, int): The size of the internal buffer for storing the remote codes. Defaults to ``10kB``
|
|
on the ESP32 and ``1kB`` on the ESP8266.
|
|
- **memory_blocks** (*Optional*, int): The number of RMT memory blocks used. Only used on ESP32 platform. Defaults to
|
|
``3``.
|
|
- **filter** (*Optional*, :ref:`config-time`): Filter any pulses that are shorter than this. Useful for removing
|
|
glitches from noisy signals. Defaults to ``50us``.
|
|
- **idle** (*Optional*, :ref:`config-time`): The amount of time that a signal should remain stable (i.e. not
|
|
change) for it to be considered complete. Defaults to ``10ms``.
|
|
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID used for code generation. Use this if you have
|
|
multiple remote receivers.
|
|
|
|
Automations:
|
|
|
|
- **on_aeha** (*Optional*, :ref:`Automation <automation>`): An automation to perform when a
|
|
AEHA remote code has been decoded. A variable ``x`` of type :apiclass:`remote_base::AEHAData`
|
|
is passed to the automation for use in lambdas.
|
|
- **on_canalsat** (*Optional*, :ref:`Automation <automation>`): An automation to perform when a
|
|
CanalSat remote code has been decoded. A variable ``x`` of type :apistruct:`remote_base::CanalSatData`
|
|
is passed to the automation for use in lambdas.
|
|
- **on_canalsatld** (*Optional*, :ref:`Automation <automation>`): An automation to perform when a
|
|
CanalSatLD remote code has been decoded. A variable ``x`` of type :apistruct:`remote_base::CanalSatLDData`
|
|
is passed to the automation for use in lambdas.
|
|
- **on_coolix** (*Optional*, :ref:`Automation <automation>`): An automation to perform when a
|
|
Coolix remote code has been decoded. A variable ``x`` of type :apiclass:`remote_base::CoolixData`
|
|
is passed to the automation for use in lambdas.
|
|
- **on_dish** (*Optional*, :ref:`Automation <automation>`): An automation to perform when a
|
|
dish network remote code has been decoded. A variable ``x`` of type :apistruct:`remote_base::DishData`
|
|
is passed to the automation for use in lambdas.
|
|
Beware that Dish remotes use a different carrier frequency (57.6kHz) that many receiver hardware don't decode.
|
|
- **on_jvc** (*Optional*, :ref:`Automation <automation>`): An automation to perform when a
|
|
JVC remote code has been decoded. A variable ``x`` of type :apistruct:`remote_base::JVCData`
|
|
is passed to the automation for use in lambdas.
|
|
- **on_lg** (*Optional*, :ref:`Automation <automation>`): An automation to perform when a
|
|
LG remote code has been decoded. A variable ``x`` of type :apistruct:`remote_base::LGData`
|
|
is passed to the automation for use in lambdas.
|
|
- **on_magiquest** (*Optional*, :ref:`Automation <automation>`): An automation to perform when a
|
|
MagiQuest wand remote code has been decoded. A variable ``x`` of type :apiclass:`remote_base::MagiQuestData`
|
|
is passed to the automation for use in lambdas.
|
|
- **on_midea** (*Optional*, :ref:`Automation <automation>`): An automation to perform when a
|
|
Midea remote code has been decoded. A variable ``x`` of type :apiclass:`remote_base::MideaData`
|
|
is passed to the automation for use in lambdas.
|
|
- **on_nec** (*Optional*, :ref:`Automation <automation>`): An automation to perform when a
|
|
NEC remote code has been decoded. A variable ``x`` of type :apistruct:`remote_base::NECData`
|
|
is passed to the automation for use in lambdas.
|
|
|
|
.. note::
|
|
|
|
In version 2021.12, the order of transferring bits was corrected from MSB to LSB in accordance with the NEC standard.
|
|
Therefore, if the configuration file has come from an earlier version of ESPhome, it is necessary to reverse the order of the address and command bits when moving to 2021.12 or above.
|
|
For example, address: 0x84ED, command: 0x13EC becomes 0xB721 and 0x37C8 respectively.
|
|
|
|
- **on_nexa** (*Optional*, :ref:`Automation <automation>`): An automation to perform when a
|
|
Nexa RF code has been decoded. A variable ``x`` of type :apiclass:`remote_base::NexaData`
|
|
is passed to the automation for use in lambdas.
|
|
- **on_panasonic** (*Optional*, :ref:`Automation <automation>`): An automation to perform when a
|
|
Panasonic remote code has been decoded. A variable ``x`` of type :apistruct:`remote_base::PanasonicData`
|
|
is passed to the automation for use in lambdas.
|
|
- **on_pioneer** (*Optional*, :ref:`Automation <automation>`): An automation to perform when a
|
|
pioneer remote code has been decoded. A variable ``x`` of type :apistruct:`remote_base::PioneerData`
|
|
is passed to the automation for use in lambdas.
|
|
- **on_pronto** (*Optional*, :ref:`Automation <automation>`): An automation to perform when a
|
|
Pronto remote code has been decoded. A variable ``x`` of type ``std::string``
|
|
is passed to the automation for use in lambdas.
|
|
- **on_raw** (*Optional*, :ref:`Automation <automation>`): An automation to perform when a
|
|
raw remote code has been decoded. A variable ``x`` of type ``std::vector<int>``
|
|
is passed to the automation for use in lambdas.
|
|
- **on_rc5** (*Optional*, :ref:`Automation <automation>`): An automation to perform when a
|
|
RC5 remote code has been decoded. A variable ``x`` of type :apistruct:`remote_base::RC5Data`
|
|
is passed to the automation for use in lambdas.
|
|
- **on_rc6** (*Optional*, :ref:`Automation <automation>`): An automation to perform when a
|
|
RC6 remote code has been decoded. A variable ``x`` of type :apistruct:`remote_base::RC6Data`
|
|
is passed to the automation for use in lambdas.
|
|
- **on_rc_switch** (*Optional*, :ref:`Automation <automation>`): An automation to perform when a
|
|
RCSwitch RF code has been decoded. A variable ``x`` of type :apistruct:`remote_base::RCSwitchData`
|
|
is passed to the automation for use in lambdas.
|
|
- **on_samsung** (*Optional*, :ref:`Automation <automation>`): An automation to perform when a
|
|
Samsung remote code has been decoded. A variable ``x`` of type :apistruct:`remote_base::SamsungData`
|
|
is passed to the automation for use in lambdas.
|
|
- **on_samsung36** (*Optional*, :ref:`Automation <automation>`): An automation to perform when a
|
|
Samsung36 remote code has been decoded. A variable ``x`` of type :apistruct:`remote_base::Samsung36Data`
|
|
is passed to the automation for use in lambdas.
|
|
- **on_sony** (*Optional*, :ref:`Automation <automation>`): An automation to perform when a
|
|
Sony remote code has been decoded. A variable ``x`` of type :apistruct:`remote_base::SonyData`
|
|
is passed to the automation for use in lambdas.
|
|
- **on_toshiba_ac** (*Optional*, :ref:`Automation <automation>`): An automation to perform when a
|
|
Toshiba AC remote code has been decoded. A variable ``x`` of type :apistruct:`remote_base::ToshibaAcData`
|
|
is passed to the automation for use in lambdas.
|
|
|
|
.. _remote-receiver-binary-sensor:
|
|
|
|
Binary Sensor
|
|
-------------
|
|
|
|
The ``remote_receiver`` binary sensor lets you track when a button on a remote control is pressed.
|
|
|
|
Each time the pre-defined signal is received, the binary sensor will briefly go ON and
|
|
then immediately OFF.
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Example configuration entry
|
|
remote_receiver:
|
|
pin: GPIO32
|
|
dump: all
|
|
|
|
binary_sensor:
|
|
- platform: remote_receiver
|
|
name: "Panasonic Remote Input"
|
|
panasonic:
|
|
address: 0x4004
|
|
command: 0x100BCBD
|
|
|
|
Configuration variables:
|
|
************************
|
|
|
|
- **name** (**Required**, string): The name for the binary sensor.
|
|
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID used for code generation.
|
|
- All other options from :ref:`Binary Sensor <config-binary_sensor>`.
|
|
|
|
Remote code selection (exactly one of these has to be included):
|
|
|
|
- **aeha**: Trigger on a decoded AEHA remote code with the given data.
|
|
|
|
- **address** (**Required**, int): The address to trigger on, see dumper output for more info.
|
|
- **data** (**Required**, 3-35 bytes list): The code to listen for, see :ref:`remote_transmitter-transmit_aeha`
|
|
for more info. Usually you only need to copy this directly from the dumper output.
|
|
|
|
- **canalsat**: Trigger on a decoded CanalSat remote code with the given data.
|
|
|
|
.. note::
|
|
|
|
The CanalSat and CanalSatLD protocols use a higher carrier frequency (56khz) and are very similar.
|
|
Depending on the hardware used they may interfere with each other when enabled simultaneously.
|
|
|
|
- **device** (**Required**, int): The device to trigger on, see dumper output for more info.
|
|
- **address** (**Optional**, int): The address (or subdevice) to trigger on, see dumper output for more info. Defaults to ``0``
|
|
- **command** (**Required**, int): The command to listen for.
|
|
|
|
- **canalsatld**: Trigger on a decoded CanalSatLD remote code with the given data.
|
|
|
|
.. note::
|
|
|
|
The CanalSat and CanalSatLD protocols use a higher carrier frequency (56khz) and are very similar.
|
|
Depending on the hardware used they may interfere with each other when enabled simultaneously.
|
|
|
|
- **device** (**Required**, int): The device to trigger on, see dumper output for more info.
|
|
- **address** (**Optional**, int): The address (or subdevice) to trigger on, see dumper output for more info. Defaults to ``0``
|
|
- **command** (**Required**, int): The command to listen for.
|
|
|
|
- **coolix**: Trigger on a decoded Coolix remote code with the given data.
|
|
|
|
- **data** (**Required**, int): The 24-bit Coolix code to trigger on, see dumper output for more info.
|
|
|
|
- **dish**: Trigger on a decoded Dish Network remote code with the given data.
|
|
Beware that Dish remotes use a different carrier frequency (57.6kHz) that many receiver hardware don't decode.
|
|
|
|
- **address** (*Optional*, int): The number of the receiver to target, between 1 and 16 inclusive. Defaults to ``1``.
|
|
- **command** (**Required**, int): The Dish command to listen for, between 0 and 63 inclusive.
|
|
|
|
- **jvc**: Trigger on a decoded JVC remote code with the given data.
|
|
|
|
- **data** (**Required**, int): The JVC code to trigger on, see dumper output for more info.
|
|
|
|
- **lg**: Trigger on a decoded LG remote code with the given data.
|
|
|
|
- **data** (**Required**, int): The LG code to trigger on, see dumper output for more info.
|
|
- **nbits** (*Optional*, int): The number of bits of the remote code. Defaults to ``28``.
|
|
|
|
- **magiquest**: Trigger on a decoded MagiQuest wand remote code with the given wand ID.
|
|
|
|
- **wand_id** (**Required**, int): The MagiQuest wand ID to trigger on, see dumper output for more info.
|
|
- **magnitude** (*Optional*, int): The magnitude of swishes and swirls of the wand. If omitted, will match on any activation of the wand.
|
|
|
|
- **midea**: Trigger on a Midea remote code with the given code.
|
|
|
|
- **code** (**Required**, 5-bytes list): The code to listen for, see :ref:`remote_transmitter-transmit_midea`
|
|
for more info. Usually you only need to copy first 5 bytes directly from the dumper output.
|
|
|
|
- **nec**: Trigger on a decoded NEC remote code with the given data.
|
|
|
|
.. note::
|
|
|
|
In version 2021.12, the order of transferring bits was corrected from MSB to LSB in accordance with the NEC standard.
|
|
Therefore, if the configuration file has come from an earlier version of ESPhome, it is necessary to reverse the order of the address and command bits when moving to 2021.12 or above.
|
|
For example, address: 0x84ED, command: 0x13EC becomes 0xB721 and 0x37C8 respectively.
|
|
|
|
- **address** (**Required**, int): The address to trigger on, see dumper output for more info.
|
|
- **command** (**Required**, int): The NEC command to listen for.
|
|
|
|
- **nexa**: Trigger on a decoded Nexa RF code with the given data.
|
|
|
|
- **device** (**Required**, int): The Nexa device code to trigger on, see dumper output for more info.
|
|
- **group** (**Required**, int): The Nexa group code to trigger on, see dumper output for more info.
|
|
- **state** (**Required**, int): The Nexa state code to trigger on, see dumper output for more info.
|
|
- **channel** (**Required**, int): The Nexa channel code to trigger on, see dumper output for more info.
|
|
- **level** (**Required**, int): The Nexa level code to trigger on, see dumper output for more info.
|
|
|
|
- **panasonic**: Trigger on a decoded Panasonic remote code with the given data.
|
|
|
|
- **address** (**Required**, int): The address to trigger on, see dumper output for more info.
|
|
- **command** (**Required**, int): The command.
|
|
|
|
- **pioneer**: Trigger on a decoded Pioneer remote code with the given data.
|
|
|
|
- **rc_code_1** (**Required**, int): The remote control code to trigger on, see dumper output for more details.
|
|
|
|
- **pronto**: Trigger on a Pronto remote code with the given code.
|
|
|
|
- **data** (**Required**, string): The code to listen for, see :ref:`remote_transmitter-transmit_raw`
|
|
for more info. Usually you only need to copy this directly from the dumper output.
|
|
|
|
- **raw**: Trigger on a raw remote code with the given code.
|
|
|
|
- **code** (**Required**, list): The code to listen for, see :ref:`remote_transmitter-transmit_raw`
|
|
for more info. Usually you only need to copy this directly from the dumper output.
|
|
|
|
- **rc5**: Trigger on a decoded RC5 remote code with the given data.
|
|
|
|
- **address** (**Required**, int): The address to trigger on, see dumper output for more info.
|
|
- **command** (**Required**, int): The RC5 command to listen for.
|
|
|
|
- **rc6**: Trigger on a decoded RC6 remote code with the given data.
|
|
|
|
- **address** (**Required**, int): The address to trigger on, see dumper output for more info.
|
|
- **command** (**Required**, int): The RC6 command to listen for.
|
|
|
|
- **rc_switch_raw**: Trigger on a decoded RC Switch raw remote code with the given data.
|
|
|
|
- **code** (**Required**, string): The remote code to listen for, copy this from the dumper output. To ignore a bit
|
|
in the received data, use ``x`` at that place in the **code**.
|
|
- **protocol** (*Optional*): The RC Switch protocol to use, see :ref:`remote_transmitter-rc_switch-protocol` for more info.
|
|
|
|
- **rc_switch_type_a**: Trigger on a decoded RC Switch Type A remote code with the given data.
|
|
|
|
- **group** (**Required**, string): The group, binary string.
|
|
- **device** (**Required**, string): The device in the group, binary string.
|
|
- **state** (**Required**, boolean): The on/off state to trigger on.
|
|
- **protocol** (*Optional*): The RC Switch protocol to use, see :ref:`remote_transmitter-rc_switch-protocol` for more info.
|
|
|
|
- **rc_switch_type_b**: Trigger on a decoded RC Switch Type B remote code with the given data.
|
|
|
|
- **address** (**Required**, int): The address, int from 1 to 4.
|
|
- **channel** (**Required**, int): The channel, int from 1 to 4.
|
|
- **state** (**Required**, boolean): The on/off state to trigger on.
|
|
- **protocol** (*Optional*): The RC Switch protocol to use, see :ref:`remote_transmitter-rc_switch-protocol` for more info.
|
|
|
|
- **rc_switch_type_c**: Trigger on a decoded RC Switch Type C remote code with the given data.
|
|
|
|
- **family** (**Required**, string): The family. Range is ``a`` to ``p``.
|
|
- **group** (**Required**, int): The group. Range is 1 to 4.
|
|
- **device** (**Required**, int): The device. Range is 1 to 4.
|
|
- **state** (**Required**, boolean): The on/off state to trigger on.
|
|
- **protocol** (*Optional*): The RC Switch protocol to use, see :ref:`remote_transmitter-rc_switch-protocol` for more info.
|
|
|
|
- **rc_switch_type_d**: Trigger on a decoded RC Switch Type D remote code with the given data.
|
|
|
|
- **group** (**Required**, int): The group. Range is 1 to 4.
|
|
- **device** (**Required**, int): The device. Range is 1 to 3.
|
|
- **state** (**Required**, boolean): The on/off state to trigger on.
|
|
- **protocol** (*Optional*): The RC Switch protocol to use, see :ref:`remote_transmitter-rc_switch-protocol` for more info.
|
|
|
|
- **samsung**: Trigger on a decoded Samsung remote code with the given data.
|
|
|
|
- **data** (**Required**, int): The data to trigger on, see dumper output for more info.
|
|
- **nbits** (*Optional*, int): The number of bits of the remote code. Defaults to ``32``.
|
|
|
|
- **samsung36**: Trigger on a decoded Samsung36 remote code with the given data.
|
|
|
|
- **address** (**Required**, int): The address to trigger on, see dumper output for more info.
|
|
- **command** (**Required**, int): The command.
|
|
|
|
- **sony**: Trigger on a decoded Sony remote code with the given data.
|
|
|
|
- **data** (**Required**, int): The Sony code to trigger on, see dumper output for more info.
|
|
- **nbits** (*Optional*, int): The number of bits of the remote code. Defaults to ``12``.
|
|
|
|
- **toshiba_ac**: Trigger on a decoded Toshiba AC remote code with the given data.
|
|
|
|
- **rc_code_1** (**Required**, int): The remote control code to trigger on, see dumper output for more details.
|
|
- **rc_code_2** (*Optional*, int): The second part of the remote control code to trigger on, see dumper output for more details.
|
|
|
|
.. note::
|
|
|
|
For the Sonoff RF Bridge you can use `this hack <https://github.com/xoseperez/espurna/wiki/Hardware-Itead-Sonoff-RF-Bridge---Direct-Hack>`__
|
|
created by the GitHub user wildwiz. Then use this configuration for the remote receiver/transmitter hubs:
|
|
|
|
.. code-block:: yaml
|
|
|
|
remote_receiver:
|
|
pin: 4
|
|
dump: all
|
|
|
|
remote_transmitter:
|
|
pin: 5
|
|
carrier_duty_percent: 100%
|
|
|
|
.. note::
|
|
|
|
To capture the codes more effectively with directly connected receiver like tsop38238 you can try to use ``INPUT_PULLUP``:
|
|
|
|
.. code-block:: yaml
|
|
|
|
remote_receiver:
|
|
pin:
|
|
number: D4
|
|
inverted: true
|
|
mode:
|
|
input: true
|
|
pullup: true
|
|
dump: all
|
|
|
|
|
|
See Also
|
|
--------
|
|
|
|
- :doc:`index`
|
|
- :doc:`/components/remote_transmitter`
|
|
- `RCSwitch <https://github.com/sui77/rc-switch>`__ by `Suat Özgür <https://github.com/sui77>`__
|
|
- `IRRemoteESP8266 <https://github.com/markszabo/IRremoteESP8266/>`__ by `Mark Szabo-Simon <https://github.com/markszabo>`__
|
|
- :apiref:`remote/remote_receiver.h`
|
|
- :ghedit:`Edit`
|