mirror of
https://github.com/esphome/esphome-docs.git
synced 2024-08-28 23:59:40 +02:00
Using it with PIR myself, but it is possible to add any type of sensor. The information of the E-LOG pin being GPIO 2, was a guess based on other type of Sonoff devices. I was unable to find information about the pinout of the Sonoff S20 E-LOG pin. This seems like a usefull place to store this information to help others.
326 lines
12 KiB
ReStructuredText
326 lines
12 KiB
ReStructuredText
Using With Sonoff S20
|
|
=====================
|
|
|
|
.. seo::
|
|
:description: Instructions for putting Sonoff S20 devices into flash mode and installing ESPHome on them.
|
|
:image: sonoff_s20.jpg
|
|
|
|
ESPHome can also be used with Sonoff S20 smart sockets. These devices are
|
|
basically just an ESP8266 chip with a relay to control the socket, a small button on the
|
|
front and a blue and green LED light.
|
|
|
|
.. figure:: images/sonoff_s20_header.jpg
|
|
:align: center
|
|
:width: 75.0%
|
|
|
|
Sonoff S20 Smart Socket.
|
|
|
|
This guide will step you through setting up your Sonoff S20 and flashing the first ESPHome firmware
|
|
with the serial interface. After that, you will be able to upload all future firmware with the remote
|
|
Over-The-Air update process.
|
|
|
|
.. note::
|
|
|
|
If you've previously installed Sonoff-Tasmota on your Sonoff S20, you're in luck 😀.
|
|
ESPHome can generate a firmware binary which you can then upload via the
|
|
Tasmota web interface. To see how to create this binary, skip to :ref:`sonoff_s20-creating-firmware`.
|
|
|
|
Since firmware version 1.6.0, iTead (the creator of this device) has removed the ability to upload
|
|
a custom firmware through their own upload process. Unfortunately, that means that the only way to
|
|
flash the initial ESPHome firmware is by physically opening the device up and using the UART
|
|
interface.
|
|
|
|
.. warning::
|
|
|
|
Opening up this device can be very dangerous if not done correctly. While the device is open,
|
|
you will be a single touch away from being electrocuted if the device is plugged in.
|
|
|
|
So, during this *entire* guide **never ever** plug the device in. Also, you should only do this
|
|
if you know what you're doing. If you, at any step, feel something is wrong or are uncomfortable
|
|
with continuing, it's best to just stop for your own safety.
|
|
|
|
It's your own responsibility to make sure everything you do during this setup process is safe.
|
|
|
|
For this guide you will need:
|
|
|
|
- Sonoff S20 😉.
|
|
- A USB to UART Bridge for flashing the device. These can be bought on Amazon (or other online stores) for less than 5 dollars.
|
|
Note that the bridge *must* be 3.3V compatible. Otherwise you will destroy your S20.
|
|
- A computer running Home Assistant with the ESPHome Home Assistant add-on.
|
|
- A screwdriver to open up the S20.
|
|
- A soldering iron and a few header pins to connect the UART interface.
|
|
|
|
Have everything? Great! Then you can start.
|
|
|
|
|
|
Step 1: Opening up the Sonoff S20
|
|
---------------------------------
|
|
|
|
The first step is to open up the Sonoff S20. Note that you do not have to run the original firmware
|
|
supplied with the Sonoff S20 before doing this step.
|
|
|
|
.. warning::
|
|
|
|
Just to repeat this: Make **absolutely sure** the device is not connected to any appliance or
|
|
plugged in before doing this step.
|
|
|
|
While the device is not plugged in, turn the back side so it's facing you and unscrew the three
|
|
black screws that hold the case together.
|
|
|
|
.. figure:: images/sonoff_s20_screws.jpg
|
|
:align: center
|
|
:width: 60.0%
|
|
|
|
There are three screws on the back of the Sonoff S20.
|
|
|
|
After that, you should be able to remove the front cover and should be greeted by a bunch of parts.
|
|
|
|
.. figure:: images/sonoff_s20_parts.jpg
|
|
:align: center
|
|
:width: 75.0%
|
|
|
|
Step 2: Connecting UART
|
|
-----------------------
|
|
|
|
We're interested in the main part of the S20 with the green PCB. On the bottom of the PCB, you will
|
|
find four unpopulated holes. These pins expose the UART interface used to flash firmware onto the device
|
|
and debug issues.
|
|
|
|
.. figure:: images/sonoff_s20_pcb.jpg
|
|
:align: center
|
|
|
|
The UART interface of the Sonoff S20.
|
|
|
|
So, in order to flash our own custom firmware, we're going to need to somehow connect the UART to USB
|
|
bridge to these pins. The only way to make a good connection here is by using a soldering iron and soldering
|
|
on some pin headers. On older models of the Sonoff S20, you were able to get the whole PCB out. Newer versions,
|
|
however, glue the PCB onto the case to avoid people flashing custom firmware. If the latter is the case,
|
|
you will just need to solder the pin headers from above - it's a bit difficult, but possible.
|
|
|
|
When you're done, it should look something like this:
|
|
|
|
.. figure:: images/sonoff_s20_uart.jpg
|
|
:align: center
|
|
|
|
Now go ahead and connect the pins to your UART bridge, making sure the S20 is not plugged in as before.
|
|
Also beware that some UART to USB bridges supply 5V on the VCC pin if it's not explicitly labelled 3.3V.
|
|
It's best to just use a multimeter and double check if it's unclear.
|
|
|
|
.. note::
|
|
|
|
On some older S20s, the ``RX`` and ``TX`` pins are swapped (sometimes even the written silkscreen is
|
|
wrong). If your upload fails with an ``error: espcomm_upload_mem failed`` message it's most likely due
|
|
to the pins being swapped. In that case, just swap ``RX`` and ``TX`` and try again - you won't break
|
|
anything if they're swapped.
|
|
|
|
.. _sonoff_s20-creating-firmware:
|
|
|
|
Step 3: Creating Firmware
|
|
-------------------------
|
|
|
|
The Sonoff S20 is based on the ``ESP8266`` platform and is a subtype of the ``esp01_1m`` board.
|
|
With this information, you can step through the ESPHome wizard (``esphome sonoff_s20.yaml wizard``),
|
|
or alternatively, you can just take the below configuration file and modify it to your needs.
|
|
|
|
|
|
.. code-block:: yaml
|
|
|
|
esphome:
|
|
name: <NAME_OF_NODE>
|
|
platform: ESP8266
|
|
board: esp8285
|
|
arduino_version: 2.4.2
|
|
|
|
wifi:
|
|
ssid: <YOUR_SSID>
|
|
password: <YOUR_PASSWORD>
|
|
|
|
api:
|
|
|
|
logger:
|
|
|
|
ota:
|
|
|
|
Now run ``esphome sonoff_s20.yaml compile`` to validate the configuration and
|
|
pre-compile the firmware.
|
|
|
|
.. note::
|
|
|
|
After this step, you will be able to find the compiled binary under
|
|
``<NAME_OF_NODE>/.pioenvs/<NAME_OF_NODE>/firmware.bin``. If you're having trouble with
|
|
uploading, you can also try uploading this file directly with other tools.
|
|
|
|
Step 4: Uploading Firmware
|
|
--------------------------
|
|
|
|
In order to upload the firmware, you're first going to need to get the chip into a flash mode, otherwise
|
|
the device will start up without accepting any firmware flash attempts. To do this, while the UART
|
|
bridge is not connected to your USB port, press and hold the small push button in the middle of the PCB.
|
|
Then plug the UART bridge into your computer and keep holding the button for 2-4 seconds.
|
|
The S20 should now be in a flash mode and should not blink any LED.
|
|
|
|
Now you can finally run the upload command:
|
|
|
|
.. code-block:: bash
|
|
|
|
esphome sonoff_s20.yaml run
|
|
|
|
If successful, you should see something like this:
|
|
|
|
.. figure:: images/sonoff_s20_upload.png
|
|
:align: center
|
|
|
|
Hooray 🎉! You've now successfully uploaded the first ESPHome firmware to your Sonoff S20. And, in a moment,
|
|
you will be able to use all of ESPHome's great features with your Sonoff S20.
|
|
|
|
If above step don't work, however, here are some steps that can help:
|
|
|
|
- Sometimes the UART bridge cannot supply enough current to the chip to operate. In this
|
|
case use a 3.3V supply you have lying around. A nice hack is to use the power supply of
|
|
NodeMCU boards. Simply connect 3.3V to VCC and GND to GND on the pins. **Do not attempt
|
|
to plug the device into a socket to overcome this problem while troubleshooting.**
|
|
- In other cases the ``TX`` and ``RX`` pin are reversed. Simple disconnect the device, swap
|
|
the two pins and put it into flash mode again.
|
|
|
|
Step 5: Adding the Button, Relay and LEDs
|
|
-----------------------------------------
|
|
|
|
Now we would like the S20 to actually do something, not just connect to WiFi and pretty much sit idle.
|
|
|
|
Below you will find a table of all usable GPIO pins of the S20 and a configuration file that exposes all
|
|
of the basic functions.
|
|
|
|
======================================== ========================================
|
|
``GPIO0`` Push Button (HIGH = off, LOW = on)
|
|
---------------------------------------- ----------------------------------------
|
|
``GPIO12`` Relay and its status LED
|
|
---------------------------------------- ----------------------------------------
|
|
``GPIO13`` Green LED (HIGH = off, LOW = on)
|
|
---------------------------------------- ----------------------------------------
|
|
``GPIO1`` ``RX`` pin (for external sensors)
|
|
---------------------------------------- ----------------------------------------
|
|
``GPIO3`` ``TX`` pin (for external sensors)
|
|
---------------------------------------- ----------------------------------------
|
|
``GPIO2`` ``E-LOG`` pin (From PCB V2.1; for external sensors)
|
|
======================================== ========================================
|
|
|
|
.. code-block:: yaml
|
|
|
|
esphome:
|
|
name: <NAME_OF_NODE>
|
|
platform: ESP8266
|
|
board: esp01_1m
|
|
|
|
wifi:
|
|
ssid: <YOUR_SSID>
|
|
password: <YOUR_PASSWORD>
|
|
|
|
api:
|
|
|
|
logger:
|
|
|
|
ota:
|
|
|
|
binary_sensor:
|
|
- platform: gpio
|
|
pin:
|
|
number: GPIO0
|
|
mode: INPUT_PULLUP
|
|
inverted: True
|
|
name: "Sonoff S20 Button"
|
|
- platform: status
|
|
name: "Sonoff S20 Status"
|
|
- platform: gpio
|
|
pin: GPIO2
|
|
name: "Sonoff S20 Sensor"
|
|
|
|
|
|
switch:
|
|
- platform: gpio
|
|
name: "Sonoff S20 Relay"
|
|
pin: GPIO12
|
|
|
|
output:
|
|
# Register the green LED as a dimmable output ....
|
|
- platform: esp8266_pwm
|
|
id: s20_green_led
|
|
pin:
|
|
number: GPIO13
|
|
inverted: True
|
|
|
|
light:
|
|
# ... and then make a light out of it.
|
|
- platform: monochromatic
|
|
name: "Sonoff S20 Green LED"
|
|
output: s20_green_led
|
|
|
|
|
|
The above example also showcases an important concept of ESPHome: IDs and linking. In order
|
|
to make all components in ESPHome as "plug and play" as possible, you can use IDs to define
|
|
them in one area, and simply pass that ID later on. For example, above you can see a PWM (dimmer)
|
|
output being created with the ID ``s20_green_led`` for the green LED. Later on it is then transformed
|
|
into a :doc:`monochromatic light </components/light/monochromatic>`.
|
|
|
|
And if you want the thing that's connected through the output of the S20 to appear as a light
|
|
in Home Assistant, replace the last part with this:
|
|
|
|
.. code-block:: yaml
|
|
|
|
switch:
|
|
- platform: restart
|
|
name: "Sonoff S20 Restart"
|
|
|
|
output:
|
|
- platform: esp8266_pwm
|
|
id: s20_green_led
|
|
pin:
|
|
number: GPIO13
|
|
inverted: True
|
|
# Note: do *not* make the relay a dimmable (PWM) signal, relays cannot handle that
|
|
- platform: gpio
|
|
id: s20_relay
|
|
pin: GPIO12
|
|
|
|
light:
|
|
- platform: monochromatic
|
|
name: "Sonoff S20 Green LED"
|
|
output: s20_green_led
|
|
- platform: binary
|
|
name: "Sonoff S20 Relay"
|
|
output: s20_relay
|
|
|
|
To make pressing the button on the front toggle the relay, have a look at the `the complete Sonoff S20
|
|
with automation example <https://github.com/OttoWinter/esphomedocs/blob/current/devices/sonoff_s20.yaml>`__.
|
|
|
|
.. figure:: images/sonoff_s20_result.png
|
|
:align: center
|
|
:width: 75.0%
|
|
|
|
Step 6: Finishing Up
|
|
--------------------
|
|
|
|
Now you're pretty much done with setting up the Sonoff S20. The only steps left are to
|
|
remove any cables that you added within the housing and make sure everything in there is clean. If, for
|
|
example, you used wires to connect the UART console, you should definitely remove them to avoid
|
|
a short with mains.
|
|
|
|
Sometimes the soldered-on header pins can also interfere with the button. It's best to remove the
|
|
header pins again, as you will hopefully not need to use them again because of ESPHome's Over-The-Air
|
|
Update features (+ the OTA safe mode; if your node reboots more than 10 times in a row, it will automatically
|
|
enter an OTA-only safe mode).
|
|
|
|
If you're sure everything is done with the S20 and have double checked there's nothing that could cause a short
|
|
in the case, you can put the front cover with the button on the base again and screw everything together.
|
|
|
|
Now triple- or even quadruple-check the UART bridge is not connected to the S20, then comes the time when you can
|
|
plug it into the socket.
|
|
|
|
Happy hacking!
|
|
|
|
See Also
|
|
--------
|
|
|
|
- :doc:`sonoff`
|
|
- :doc:`sonoff_4ch`
|
|
- :ghedit:`Edit`
|