200 lines
9.1 KiB
ReStructuredText
200 lines
9.1 KiB
ReStructuredText
INA2xx family of digital power monitors
|
||
=======================================
|
||
|
||
.. seo::
|
||
:description: Instructions for setting up INA228, INA229, INA237, INA238, INA239 DC current, power, and charge sensors
|
||
:image: ina228.jpg
|
||
:keywords: ina228 ina229 ina237 ina238 ina239
|
||
|
||
.. figure:: images/ina228-full.jpg
|
||
:align: center
|
||
:width: 50.0%
|
||
|
||
INA228 Module with integrated shunt from Adafruit
|
||
|
||
Supported devices
|
||
-----------------
|
||
The ``ina2xx`` sensor platform allows you to use family of Texas Instruments current and power
|
||
sensors with ESPHome. Appropriate interface (:ref:`I²C Bus <i2c>` or :ref:`SPI Bus <spi>`) is
|
||
requred to be set up in your configuration for this sensor to work.
|
||
|
||
|
||
|
||
========================================================== ========== ==========================================================
|
||
Product Protocol Description
|
||
========================================================== ========== ==========================================================
|
||
`INA228 <http://www.ti.com/lit/ds/symlink/ina228.pdf>`__ I²C 85-V, 20-Bit, Ultra-Precise Power/Energy/Charge Monitor
|
||
`INA229 <http://www.ti.com/lit/ds/symlink/ina229.pdf>`__ SPI 85-V, 20-Bit, Ultra-Precise Power/Energy/Charge Monitor
|
||
`INA238 <http://www.ti.com/lit/ds/symlink/ina238.pdf>`__ I²C 85-V, 16-Bit, High-Precision Power Monitor
|
||
`INA239 <http://www.ti.com/lit/ds/symlink/ina239.pdf>`__ SPI 85-V, 16-Bit, High-Precision Power Monitor
|
||
`INA237 <http://www.ti.com/lit/ds/symlink/ina237.pdf>`__ I²C 85-V, 16-Bit, Precision Power Monitor
|
||
========================================================== ========== ==========================================================
|
||
|
||
All devices can measure a selectable full-scale differential input of ±163.84 mV
|
||
or ±40.96 mV across the shunt with common-mode voltage support from –0.3 V to +85 V.
|
||
|
||
INA228 and INA229 are the most comprehensive devices of the family with extra features: 20-bit ADC resolution,
|
||
energy and charge accumulation, and capability to utilize the temperature measurement to compensate
|
||
for shunt resistor temperature variance.
|
||
|
||
Over I²C
|
||
--------
|
||
Use ``ina2xx_i2c`` component to connect INA228, INA237, or INA238 device over :ref:`I²C <i2c>` bus.
|
||
|
||
.. code-block:: yaml
|
||
|
||
# Example configuration entry for I²C
|
||
i2c:
|
||
sda: D1
|
||
scl: D2
|
||
|
||
sensor:
|
||
- platform: ina2xx_i2c
|
||
id: my_charge_sensor
|
||
model: INA228
|
||
address: 0x40
|
||
shunt_resistance: 0.010 ohm
|
||
max_current: 10 A
|
||
adc_range: 0
|
||
update_interval: 60s
|
||
current: "INA228 Current"
|
||
bus_voltage: "INA228 Bus Voltage"
|
||
charge: "INA228 Charge"
|
||
|
||
|
||
Configuration variables:
|
||
************************
|
||
|
||
- **model** (**Required**, string): The model of the INA2xx sensor. Options are ``INA228``, ``INA237``, ``INA238``.
|
||
- **address** (*Optional*, int): Manually specify the I²C address of the sensor. Defaults to ``0x40``.
|
||
- **shunt_resistance** (**Required**, float): The value of the shunt resistor used for current calculation. No default value.
|
||
- **max_current** (**Required**, float): The maximum current you are expecting. Component will use it to
|
||
calibrate the sensor. No default value.
|
||
- **adc_range** (*Optional*, ``0`` or ``1``): Selects the range for differential input across shunt
|
||
resistor. ``0`` for ±163.84 mV, ``1`` for ±40.96 mV range. Defaults to ``0``.
|
||
- **adc_time** (*Optional*, :ref:`config-time`): The time in microseconds to perform a single ADC conversion.
|
||
Defaults to ``4120 us``. Valid values are ``50 us``, ``84 us``, ``150 us``, ``280 us``, ``540 us``,
|
||
``1052 us``, ``2074 us``, ``4120 us``.
|
||
|
||
Instead of one time for all ADC measurements, separate configuration of conversion times for shunt voltage,
|
||
bus voltage, and temperature measurements possible. Options are the same as for ``adc_time``.
|
||
|
||
- **bus_voltage** (*Optional*, :ref:`config-time`): Conversion time for bus voltage measurement.
|
||
- **shunt_voltage** (*Optional*, :ref:`config-time`): Conversion time for shunt voltage measurement.
|
||
- **temperature** (*Optional*, :ref:`config-time`): Conversion time for temperature measurement.
|
||
|
||
- **adc_averaging** (*Optional*, integer): Selects ADC sample averaging count. Defaults to ``128``.
|
||
Valid values are ``1``, ``4``, ``16``, ``64``, ``128``, ``256``, ``512``, ``1024``.
|
||
- **temperature_coefficient** (*Optional*, integer from ``0`` to ``16383``): Temperature coefficient (ppm/°C) of the
|
||
shunt for temperature compensation correction. Only applicable to INA228 and INA229 devices. Zero value means
|
||
no compensation is done. Defaults to ``0``.
|
||
- **update_interval** (*Optional*, :ref:`config-time`): The interval to check the sensor. Defaults to ``60s``.
|
||
- All other options for I²C device as descibed in respective documentation.
|
||
|
||
|
||
Over SPI
|
||
--------
|
||
|
||
Use ``ina2xx_spi`` component to connect INA229 or INA239 device over :ref:`SPI <spi>` bus.
|
||
|
||
|
||
.. code-block:: yaml
|
||
|
||
# Example configuration entry for SPI
|
||
spi:
|
||
clk_pin: D0
|
||
mosi_pin: D1
|
||
miso_pin: D2
|
||
|
||
sensor:
|
||
- platform: ina2xx_spi
|
||
cs_pin: D3
|
||
model: INA239
|
||
shunt_resistance: 0.001130 ohm
|
||
max_current: 40 A
|
||
adc_range: 0
|
||
temperature_coefficient: 50
|
||
current: "INA239 Current"
|
||
power: "INA239 Power"
|
||
|
||
|
||
Configuration variables:
|
||
************************
|
||
|
||
- **model** (**Required**, string): The model of the INA2xx sensor. Options are ``INA229``, ``INA239``.
|
||
- **cs_pin** (**Required**, :ref:`Pin Schema <config-pin_schema>`): The Chip Select (CS) pin.
|
||
- **shunt_resistance** (**Required**, float): The value of the shunt resistor used for current calculation. No default value.
|
||
- **max_current** (**Required**, float): The maximum current you are expecting. Component will use it to
|
||
calibrate the sensor. No default value.
|
||
- **adc_range** (*Optional*, ``0`` or ``1``): Selects the range for differential input across shunt
|
||
resistor. ``0`` for ±163.84 mV, ``1`` for ±40.96 mV range. Defaults to ``0``.
|
||
- **adc_time** (*Optional*, :ref:`config-time`): The time in microseconds to perform a single ADC conversion.
|
||
Defaults to ``4120 us``. Valid values are ``50 us``, ``84 us``, ``150 us``, ``280 us``, ``540 us``,
|
||
``1052 us``, ``2074 us``, ``4120 us``.
|
||
|
||
Instead of one time for all ADC measurements, separate configuration of conversion times for shunt voltage,
|
||
bus voltage, and temperature measurements possible. Options are the same as for ``adc_time``.
|
||
|
||
- **bus_voltage** (*Optional*, :ref:`config-time`): Conversion time for bus voltage measurement.
|
||
- **shunt_voltage** (*Optional*, :ref:`config-time`): Conversion time for shunt voltage measurement.
|
||
- **temperature** (*Optional*, :ref:`config-time`): Conversion time for temperature measurement.
|
||
|
||
- **adc_averaging** (*Optional*, integer): Selects ADC sample averaging count. Defaults to ``128``.
|
||
Valid values are ``1``, ``4``, ``16``, ``64``, ``128``, ``256``, ``512``, ``1024``.
|
||
- **temperature_coefficient** (*Optional*, integer from ``0`` to ``16383``): Temperature coefficient (ppm/°C) of the
|
||
shunt for temperature compensation correction. Only applicable to INA228 and INA229 devices. Zero value means
|
||
no compensation is done. Defaults to ``0``.
|
||
- **update_interval** (*Optional*, :ref:`config-time`): The interval to check the sensor. Defaults to ``60s``.
|
||
- All other options for SPI device as descibed in respective documentation.
|
||
|
||
|
||
Sensors
|
||
-------
|
||
The component offers nine sensors. You can configure all or any subset of the sensors. Each configured sensor
|
||
is reported separately on each update_interval. The ``name`` option is required for each sensor configured.
|
||
All other options from :ref:`Sensor <config-sensor>`. Shorthand notation can be used for the sensors like this:
|
||
``current: "Current"``.
|
||
|
||
- **current** (*Optional*): Calculated current output, A
|
||
- **power** (*Optional*): Calculated power output, always positive, W
|
||
- **shunt_voltage** (*Optional*): Differential voltage measured across the shunt, mV
|
||
- **bus_voltage** (*Optional*): Bus voltage output, V
|
||
- **temperature** (*Optional*): Internal die temperature measurement, °C
|
||
- **energy** (*Optional*): Calculated energy output, Wh (*INA228/229 only*)
|
||
- **energy_joules** (*Optional*): Calculated energy output, Joules (*INA228/229 only*)
|
||
- **charge** (*Optional*): Calculated charge output, Ah (*INA228/229 only*)
|
||
- **charge_coulombs** (*Optional*): Calculated charge output, Coulombs (*INA228/229 only*)
|
||
|
||
Lambda calls
|
||
------------
|
||
|
||
The component exposes one function to reset INA228/INA229 energy and charge accumulators.
|
||
|
||
- ``reset_energy_counters()``
|
||
|
||
.. code-block:: cpp
|
||
|
||
// Within lambda, reset counters.
|
||
id(my_charge_sensor).reset_energy_counters();
|
||
|
||
To simplify the use of this function, you can use the following example to add a button to reset the counters.
|
||
|
||
.. code-block:: yaml
|
||
|
||
button:
|
||
- platform: template
|
||
name: "Reset counters"
|
||
on_press:
|
||
- lambda: "id(my_change_sensor).reset_energy_counters();"
|
||
|
||
|
||
See Also
|
||
--------
|
||
|
||
- :ref:`sensor-filters`
|
||
- :doc:`ina219`
|
||
- :doc:`ina226`
|
||
- :doc:`ina3221`
|
||
- :apiref:`ina2xx_base/ina2xx_base.h`
|
||
- :ghedit:`Edit`
|