mirror of
https://github.com/esphome/esphome-docs.git
synced 2024-11-09 10:02:45 +01:00
132 lines
4.7 KiB
ReStructuredText
132 lines
4.7 KiB
ReStructuredText
Using With Sonoff Basic
|
|
=======================
|
|
|
|
esphomeyaml can be used with Sonoff Basic. These devices are basically just
|
|
an ESP8266 chip with a relay to control the connection, a small button on the
|
|
front and a green LED light.
|
|
|
|
.. figure:: images/sonoff_basic-full.jpg
|
|
:align: center
|
|
:width: 75.0%
|
|
|
|
Sonoff Basic
|
|
|
|
This guide will not guide you through setting up your Sonoff Basic step-by-step. It just provide
|
|
a sample configuration. For detailed instructions, see :doc:`sonoff_s20`, as those devices are
|
|
pretty similar.
|
|
|
|
.. note::
|
|
|
|
If you've previously installed Sonoff-Tasmota or ESPurna on your Sonoff Basic, you're in luck 😀
|
|
esphomeyaml can generate a firmware binary which you can then upload via the
|
|
web interface.
|
|
|
|
Sample configuration
|
|
--------------------
|
|
|
|
The Sonoff Basic is based on the ``ESP8266`` platform and is a subtype of the ``esp01_1m`` board.
|
|
With this information, you can also step through the esphomeyaml wizard (``esphomeyaml sonoff_basic.yaml wizard``)
|
|
if you don't want to use the sample configuration file from below.
|
|
|
|
If you go through the wizard, please make sure you manually set ``board_flash_mode`` to ``dout``
|
|
as seen below. The version of the uploader used by esphomeyaml should automatically detect that
|
|
the Sonoff Basic uses the ``dout`` SPI flash chip mode. But, as some users of other firmwares have
|
|
said that other flash modes can brick the device, it's always good to specify it explicitly.
|
|
|
|
Below you will find a table of all usable GPIO pins of the Sonoff Basic and a configuration file that
|
|
exposes all of the basic functions.
|
|
|
|
.. table::
|
|
:class: no-center
|
|
|
|
================================================== ==================================================
|
|
``GPIO0`` Button (inverted)
|
|
-------------------------------------------------- --------------------------------------------------
|
|
``GPIO1`` ``RX`` pin (for external sensors)
|
|
-------------------------------------------------- --------------------------------------------------
|
|
``GPIO3`` ``TX`` pin (for external sensors)
|
|
-------------------------------------------------- --------------------------------------------------
|
|
``GPIO4`` Optional Sensor
|
|
-------------------------------------------------- --------------------------------------------------
|
|
``GPIO12`` Relay and Red LED
|
|
-------------------------------------------------- --------------------------------------------------
|
|
``GPIO13`` Green LED (inverted)
|
|
-------------------------------------------------- --------------------------------------------------
|
|
``GPIO14`` Optional Sensor
|
|
-------------------------------------------------- --------------------------------------------------
|
|
``GPIO17`` Analog Input
|
|
================================================== ==================================================
|
|
|
|
.. code:: yaml
|
|
|
|
esphomeyaml:
|
|
name: <NAME_OF_NODE>
|
|
platform: ESP8266
|
|
board: esp01_1m
|
|
board_flash_mode: dout
|
|
|
|
wifi:
|
|
ssid: <YOUR_SSID>
|
|
password: <YOUR_PASSWORD>
|
|
|
|
mqtt:
|
|
broker: <YOUR_MQTT_BROKER>
|
|
username: <YOUR_USERNAME>
|
|
password: <YOUR_PASSWORD>
|
|
|
|
logger:
|
|
|
|
ota:
|
|
|
|
binary_sensor:
|
|
- platform: gpio
|
|
pin:
|
|
number: GPIO0
|
|
mode: INPUT_PULLUP
|
|
inverted: True
|
|
name: "Sonoff Basic Button"
|
|
- platform: status
|
|
name: "Sonoff Basic Status"
|
|
|
|
switch:
|
|
- platform: gpio
|
|
name: "Sonoff Basic Relay"
|
|
pin: GPIO12
|
|
|
|
output:
|
|
- platform: esp8266_pwm
|
|
id: basic_green_led
|
|
pin:
|
|
number: GPIO13
|
|
inverted: True
|
|
|
|
light:
|
|
- platform: monochromatic
|
|
name: "Sonoff Basic Green LED"
|
|
output: basic_green_led
|
|
|
|
Now run ``esphomeyaml sonoff_basic.yaml compile`` to validate the configuration and
|
|
pre-compile the firmware.
|
|
|
|
.. note::
|
|
|
|
After this step, you will be able to find the compiled binary under
|
|
``<NAME_OF_NODE>/.pioenvs/<NAME_OF_NODE>/firmware.bin``. If you're having trouble with
|
|
uploading, you can also try uploading this file directly with other tools.
|
|
|
|
Or run the upload command if your device is connected to the serial interface:
|
|
|
|
.. code:: bash
|
|
|
|
esphomeyaml sonoff_basic.yaml run
|
|
|
|
See Also
|
|
--------
|
|
|
|
- :doc:`sonoff`
|
|
- :doc:`sonoff_4ch`
|
|
- :doc:`sonoff_s20`
|
|
- `Edit this page on GitHub <https://github.com/OttoWinter/esphomedocs/blob/current/esphomeyaml/devices/sonoff_basic.rst>`__
|
|
|
|
.. disqus::
|