esphome-docs/esphomeyaml/components/switch/remote_transmitter.rst
2018-08-27 13:21:30 +02:00

353 lines
13 KiB
ReStructuredText

Remote Transmitter Switch
=========================
The ``remote_transmitter`` switch platform allows you to create switches
that send a pre-defined remote control sequence
using the :doc:`/esphomeyaml/components/remote_transmitter`. Every time
the switch is turned on, the configured remote signal is sent.
Use cases include, but are not limited to, infrared remotes, 433MHz signals and so on.
.. figure:: images/remote_transmitter-ui.png
:align: center
:width: 80.0%
.. code:: yaml
# Example configuration entry
remote_transmitter:
pin: 32
# Individual switches
switch:
- platform: remote_transmitter
name: "Panasonic TV Off"
panasonic:
address: 0x4004
command: 0x100BCBD
repeat: 25
Configuration variables:
------------------------
- **name** (**Required**, string): The name for the switch.
- The remote code, see :ref:`remote_transmitter-codes`. Only one
of them can be specified per switch.
- **repeat** (*Optional*, int): How often the command should be sent.
- **times** (int): The number of times the code should be sent. Defaults to ``1``.
- **wait_time** (:ref:`time <config-time>`): The time to wait between repeats.
- **remote_transmitter_id** (*Optional*, :ref:`config-id`): The id of the :doc:`/esphomeyaml/components/remote_transmitter`.
Defaults to the first hub specified.
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID used for code generation.
- All other options from :ref:`Switch <config-switch>` and :ref:`MQTT Component <config-mqtt-component>`.
.. note::
For the Sonoff RF Bridge you can use `this hack <https://github.com/xoseperez/espurna/wiki/Hardware-Itead-Sonoff-RF-Bridge---Direct-Hack>`__
created by the Github user wildwiz. Then use this configuration for the remote receiver/transmitter hubs:
.. code:: yaml
remote_receiver:
pin: 4
dump: all
remote_transmitter:
pin: 5
carrier_duty_percent: 100%
Supporting the RF Bridge chip directly is currently only a long-term goal for esphomelib.
.. _remote_transmitter-codes:
Remote Codes
------------
Supported remote codes:
.. code:: yaml
switch:
- platform: remote_transmitter
# ... - Only one of these is allowed for one remote transmitter at a time
nec:
address: 0x4242
command: 0x8484
lg:
data: 0x01234567890ABC
nbits: 28
sony:
data: 0xABCDEF
nbits: 12
panasonic:
address: 0x4004
command: 0x1000BCD
rc_switch_raw:
code: '001010011001111101011011'
protocol: 1
rc_switch_type_a:
group: '11001'
device: '01000'
state: True
rc_switch_type_b:
address: 4
channel: 2
state: True
rc_switch_type_c:
family: 'a'
group: 1
device: 2
state: True
rc_switch_type_d:
group: 'a'
device: 2
state: True
raw:
carrier_frequency: 35kHz
data:
- 1000
- -1000
Configuration variables:
- **nec**: Send a NEC IR code.
- **address**: The address of the device.
- **command**: The command to send.
- **lg**: Send an LG IR code.
- **data**: The data bytes to send.
- **nbits**: The number of bits to send, defaults to 28.
- **sony**: Send an Sony IR code.
- **data**: The data bytes to send.
- **nbits**: The number of bits to send, defaults to 12.
- **panasonic**: Send an Panasonic IR code.
- **address**: The address of the device.
- **command**: The command to send.
- **rc_switch_raw**: Send an RCSwitch raw code.
- **code** (**Required**, string): The code to send. Must be a string of 0s and 1s.
`For example <https://github.com/sui77/rc-switch/wiki/HowTo_OperateLowCostOutlets#type-d-status>`__ ``'001010011001111101011011'``.
- **protocol** (*Optional*, :ref:`RCSwitch protocol <rc_switch-protocol>`): The RCSwitch protocol to use. Defaults to ``1``.
- **rc_switch_type_a**: Send an RCSwitch `type A code <https://github.com/sui77/rc-switch/wiki/HowTo_OperateLowCostOutlets#type-a-10-pole-dip-switches>`__.
- **group** (**Required**, string): The group to address, usually the state of the first 5 DIP switches.
Must be a string of 0s and 1s. For example ``'11001``.
- **device** (**Required**, string): The device within the group, usually the state of the last 5 DIP switches.
Must be a string of 0s and 1s. For example ``'01000``.
- **state** (**Required**, boolean): Whether to send a "turn on" or "turn off" signal when this switch is triggered. See :ref:`remote_transmitter-on_off_template`.
- **protocol** (*Optional*, :ref:`RCSwitch protocol <rc_switch-protocol>`): The RCSwitch protocol to use. Defaults to ``1``.
- **rc_switch_type_b**: Send an RCSwitch `type B code <https://github.com/sui77/rc-switch/wiki/HowTo_OperateLowCostOutlets#type-b-two-rotarysliding-switches>`__.
- **address** (**Required**, int): The number of the first rotary switch. For example ``4``.
- **channel** (**Required**, int): The number of the first rotary switch. For example ``2``.
- **state** (**Required**, boolean): Whether to send a "turn on" or "turn off" signal when this switch is triggered. See :ref:`remote_transmitter-on_off_template`.
- **protocol** (*Optional*, :ref:`RCSwitch protocol <rc_switch-protocol>`): The RCSwitch protocol to use. Defaults to ``1``.
- **rc_switch_type_c**: Send an RCSwitch `type C code <https://github.com/sui77/rc-switch/wiki/HowTo_OperateLowCostOutlets#type-c-intertechno>`__.
- **family** (**Required**, string): The family of the device. Must be a character from ``a`` to ``p``.
- **group** (**Required**, int): The group of the device. For example ``4``.
- **address** (**Required**, int): The address of the device. For example ``2``.
- **state** (**Required**, boolean): Whether to send a "turn on" or "turn off" signal when this switch is triggered. See :ref:`remote_transmitter-on_off_template`.
- **protocol** (*Optional*, :ref:`RCSwitch protocol <rc_switch-protocol>`): The RCSwitch protocol to use. Defaults to ``1``.
- **rc_switch_type_d**: Send an RCSwitch type D code.
- **group** (**Required**, string): The group of the device. Must be a character from ``a`` to ``d``.
- **device** (**Required**, int): The address of the device. For example ``3``.
- **state** (**Required**, boolean): Whether to send a "turn on" or "turn off" signal when this switch is triggered. See :ref:`remote_transmitter-on_off_template`.
- **protocol** (*Optional*, :ref:`RCSwitch protocol <rc_switch-protocol>`): The RCSwitch protocol to use. Defaults to ``1``.
- **raw**: Send an arbitrary signal.
- **carrier_frequency**: The frequency to use for the carrier. A lot
of IR sensors only respond to a very specific frequency.
- **data**: List containing integers describing the signal to send.
Each value is a time in µs declaring how long the carrier should
be switched on or off. Positive values mean ON, negative values
mean OFF.
.. _finding_remote_codes:
Finding Remote Codes
--------------------
Each remote transmitter uses a different protocol to send its information. So to replicate an infrared or 433MHz
remote you will first need to "learn" these codes. You will first need to hook up a receiver and sniff the codes
using the :doc:`remote receiver component </esphomeyaml/components/remote_receiver>` like this:
.. code:: yaml
remote_receiver:
pin: GPIO34
# dump all signals we find
dump: all
And then activate the remote control you want to have in esphomelib. you will see a log output like this:
.. figure:: images/rf_receiver-log_raw.png
:align: center
Example log output for a 433MHz proprietary remote control.
Raw Remote Codes
****************
If esphomelib has a decoder set up for the code, it will spit out the decoded code in the logs. In this case,
it's a proprietary protocol which would be difficult to reverse engineer. Fortunately, we can just
do a "replay attack" by repeating the signal we just saw for our own purposes. The output you see in above image
is encoded in microseconds: A negative value represents the output being LOW for x microseconds and a positive
value denotes the output being HIGH for the specified number of microseconds.
Now you only need to set up the remote transmitter (which well *send* the code) like this:
.. code:: yaml
remote_transmitter:
pin: GPIO23
# Set to 100% when working with RF signals, and 50% if working with IR leds
carrier_duty_percent: 100%
And lastly, we need to set up the switch that, when turned on, will send our pre-defined remote code:
.. code:: yaml
switch:
- platform: remote_transmitter
name: "My awesome RF switch"
raw: [4088, -1542, 1019, -510, 513, -1019, 510, -509, 511, -510, 1020,
-1020, 1022, -1019, 510, -509, 511, -510, 511, -509, 511, -510,
1020, -1019, 510, -511, 1020, -510, 512, -508, 510, -1020, 1022,
-1021, 1019, -1019, 511, -510, 510, -510, 1022, -1020, 1019,
-1020, 511, -511, 1018, -1022, 1020, -1019, 1021, -1019, 1020,
-511, 510, -1019, 1023, -1019, 1019, -510, 512, -508, 510, -511,
512, -1019, 510, -509]
Note that you don't need to include the leading ``32519`` here, as it denotes a final space at the end of
a transmission.
RCSwitch Remote Codes
*********************
Starting with version 1.8.0 esphomelib can also recognize a bunch of 433MHz RF codes directly using `RCSwitch's <https://github.com/sui77/rc-switch>`__
remote protocol. If you have RF code dumping enabled for the receiver, you will then see log outputs like this one:
.. code::
Received RCSwitch: protocol=1 data='0100010101'
Like before with raw codes, you can then use this code to create switches:
.. code:: yaml
switch:
- platform: remote_transmitter
name: "Living Room Lights On"
rc_switch_raw:
code: '0100010101'
protocol: 1
Alternatively, you can use the information on `this page <https://github.com/sui77/rc-switch/wiki/HowTo_OperateLowCostOutlets>`__
to manually find the RCSwitch codes without having to first find them using the remote receiver. For example, this would
be the esphomelib equivalent of the first Type-A switch on that site:
.. code:: yaml
switch:
- platform: remote_transmitter
name: "Living Room Lights On"
rc_switch_type_a:
group: '1101'
device: '0100'
state: True
.. _remote_transmitter-on_off_template:
On/Off template
---------------
Each switch of the ``remote_transmitter`` platform only sends a pre-defined remote code when switched on.
For example the RCSwitch example above always **sends the turn on** RF code to the wall plug. In some cases
you might want to have switches that can do both things, i.e. turn a light on when switched on and turn a light off
when switched off. To do this, use the :doc:`/esphomeyaml/components/switch/template` like this:
.. code:: yaml
switch:
- platform: remote_transmitter
id: living_room_lights_on
rc_switch_type_a:
group: '1101'
device: '0100'
state: True
- platform: remote_transmitter
id: living_room_lights_off
rc_switch_type_a:
group: '1101'
device: '0100'
state: False
- platform: template
name: Living Room Lights
optimistic: True
turn_on_action:
- switch.turn_on: living_room_lights_on
turn_off_action:
- switch.turn_on: living_room_lights_off
.. _rc_switch-protocol:
RCSwitch Protocol
-----------------
RCSwitch transmitters/receivers all have a ``protocol:`` option that can be used to tell esphomelib what timings to use
for the transmission. This is necessary as many remotes use different timings to encode a logic zero or one.
RCSwitch has 7 built-in protocols that cover most use cases. You can however also choose to use custom parameters
for the protocol like so
.. code:: yaml
# Use one of RCSwitch's pre-defined protocols (1-7)
protocol: 1
# Use a custom protocol:
protocol:
pulse_length: 175
sync: [1, 31]
zero: [1, 3]
one: [3, 1]
inverted: False
Configuration options for the custom variant:
- **pulse_length** (**Required**, int): The length of each pulse in microseconds.
- **sync** (*Optional*): The number of on and off pulses for a sync bit. Defaults to 1 pulse on and 31 pulses off.
- **zero** (*Optional*): The number of on and off pulses to encode a logic zero. Defaults to 1 pulse on and 3 pulses off.
- **one** (*Optional*): The number of on and off pulses to encode a logic one. Defaults to 3 pulses on and 1 pulse off.
- **inverted** (*Optional*, boolean): Whether to treat this protocol as inverted, i.e. encode all on pulses by logic LOWs
and vice versa.
See Also
--------
- :doc:`index`
- :doc:`/esphomeyaml/components/remote_transmitter`
- :doc:`/esphomeyaml/components/remote_receiver`
- `RCSwitch <https://github.com/sui77/rc-switch>`__ by `Suat Özgür <https://github.com/sui77>`__
- `IRRemoteESP8266 <https://github.com/markszabo/IRremoteESP8266/>`__ by `Mark Szabo-Simon <https://github.com/markszabo>`__
- :doc:`API Reference </api/switch/remote_transmitter>`
- `Edit this page on GitHub <https://github.com/OttoWinter/esphomedocs/blob/current/esphomeyaml/components/switch/remote_transmitter.rst>`__