mirror of
https://github.com/esphome/esphome-docs.git
synced 2024-11-05 09:20:08 +01:00
0b041128a6
* fix enum docs style * schema fixes updates for 2023.2 * support multi key prop * format fixes * Format fixes * set typed * fix code quotes * add platforms --------- Co-authored-by: H. Árkosi Róbert <robreg@zsurob.hu>
87 lines
4.0 KiB
ReStructuredText
87 lines
4.0 KiB
ReStructuredText
Sigma-Delta Output
|
|
==================
|
|
|
|
This integration uses `sigma-delta modulation <https://en.wikipedia.org/wiki/Delta-sigma_modulation>`__
|
|
to output a floating-point value on a binary output. Unlike with :doc:`/components/output/slow_pwm`,
|
|
it is possible to update the output value with each update cycle, not just at the end of a longer period.
|
|
|
|
.. figure:: images/sigma-delta-example.png
|
|
:align: center
|
|
:width: 65.0%
|
|
|
|
Comparison between a *Slow PWM* with a period of 100s and a *sigma-delta output* with an update interval of 1s
|
|
|
|
For example, if you choose to toggle the output at most once every 1 second and decide on a
|
|
PWM period of 10 seconds, for reasonably frequent updates, with :doc:`/components/output/slow_pwm`
|
|
there are only 10 possible levels, and for higher precision a longer update interval is needed,
|
|
restricting the update rate.
|
|
|
|
A *sigma-delta* output is updated during each cycle, thus a higher precision can be achieved, without
|
|
being constrained by a calculation timeframe (=period).
|
|
|
|
So instead of having to define a ``period`` where the width of the pulse determines the output level, here you
|
|
choose an ``update_interval`` which acts like a clock signal from where the pulse density determines the output level.
|
|
|
|
This component can be used as a drop-in replacement for :doc:`/components/output/slow_pwm` by changing the ``platform`` to
|
|
``sigma_delta_output`` and changing ``period`` to ``update_interval`` (you usually want to set the *sigma-delta*'s
|
|
``update_interval`` as a fraction of *Slow PWM*'s ``period`` for similar results)
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Example configuration entry
|
|
output:
|
|
- platform: sigma_delta_output
|
|
update_interval: 10s
|
|
id: sd_heater_output
|
|
|
|
# Output to a pin
|
|
pin: 15
|
|
|
|
# Use the same output, but through automations
|
|
turn_on_action:
|
|
then:
|
|
- output.turn_on: heater_relay
|
|
turn_off_action:
|
|
then:
|
|
- output.turn_off: heater_relay
|
|
|
|
- platform: gpio
|
|
pin: 15
|
|
id: heater_relay
|
|
|
|
Configuration variables:
|
|
|
|
- **update_interval** (**Required**, :ref:`Time <config-time>`): The cycle interval at which the output is recalculated.
|
|
- **pin** (*Optional*, :ref:`Pin Schema <config-pin_schema>`): The pin to pulse.
|
|
- **state_change_action** (*Optional*, :ref:`Automation <automation>`): An automation to perform when the load is switched. If a lambda is used the boolean ``state`` parameter holds the new status.
|
|
- **turn_on_action** (*Optional*, :ref:`Automation <automation>`): An automation to perform when the load is turned on. Can be used to control for example a switch or output component.
|
|
- **turn_off_action** (*Optional*, :ref:`Automation <automation>`): An automation to perform when the load is turned off. ``turn_on_action`` and ``turn_off_action`` must be configured together.
|
|
- All options from :ref:`Output <config-output>`.
|
|
|
|
.. note::
|
|
|
|
- If ``pin`` is defined, the GPIO pin state is writen before any action is executed.
|
|
- ``state_change_action`` and ``turn_on_action``/``turn_off_action`` can be used togther. ``state_change_action`` is called before ``turn_on_action``/``turn_off_action``. It's recommended to use either ``state_change_action`` or ``turn_on_action``/``turn_off_action`` to change the state of an output. Using both automations together is only recommended for monitoring.
|
|
|
|
|
|
.. note::
|
|
|
|
If the output must not be active for more than some fixed time before it has
|
|
to be off for a while to e.g. cool down, :doc:`/components/output/slow_pwm`
|
|
should be used with a ``max_power`` setting to better control the duty
|
|
cycle.
|
|
|
|
See Also
|
|
--------
|
|
|
|
- :doc:`/components/output/index`
|
|
- :doc:`/components/output/esp8266_pwm`
|
|
- :doc:`/components/output/ledc`
|
|
- :doc:`/components/output/slow_pwm`
|
|
- :doc:`/components/light/monochromatic`
|
|
- :doc:`/components/fan/speed`
|
|
- :doc:`/components/power_supply`
|
|
- `Sigma-Delta <https://en.wikipedia.org/wiki/Delta-sigma_modulation>`__
|
|
- :apiref:`sigma_delta_output/sigma_delta_output.h`
|
|
- :ghedit:`Edit`
|