168 lines
4.4 KiB
ReStructuredText
168 lines
4.4 KiB
ReStructuredText
H801 RGBW LED controller
|
|
========================
|
|
|
|
The H801 is pretty affordable and easy to hack and adapt to your needs. It can be found on `AliExpress <https://s.click.aliexpress.com/e/bbnUDBZW>`__
|
|
and other sites. The board is based on an `ESP8266EX <https://www.espressif.com/sites/default/files/documentation/0a-esp8266ex_datasheet_en.pdf>`__ chip.
|
|
|
|
It has 5 seperate PWM outputs (each driven by a `DTU35N06 <http://www.din-tek.jp/Upload/Product%20Doc/Datasheet/DTU35N06.pdf>`__ MOSFET rated
|
|
for 106W max power), and can be used as a :doc:`RGB </components/light/rgb>` / :doc:`RGBW </components/light/rgbw>` /
|
|
:doc:`RGBWW </components/light/rgbww>` / :doc:`RGBCT </components/light/rgbct>` controller or configured with any combination of up to
|
|
five :doc:`individual monochromatic PWM </components/light/monochromatic>` lights.
|
|
See `A closer look at the H801 LED WiFi Controller <https://tinkerman.cat/post/closer-look-h801-led-wifi-controller>`__ for more details on the hardware.
|
|
|
|
.. figure:: images/h801.jpg
|
|
:align: center
|
|
:width: 80.0%
|
|
|
|
Sample configuration
|
|
--------------------
|
|
|
|
You can use the :doc:`RGBWW </components/light/rgbww>` and the :doc:`ESP8266 Software PWM output </components/output/esp8266_pwm>` components using below configuration:
|
|
|
|
.. code-block:: yaml
|
|
|
|
esphome:
|
|
name: h801light
|
|
|
|
esp8266:
|
|
board: esp01_1m
|
|
|
|
wifi:
|
|
ssid: !secret wifi_ssid
|
|
password: !secret wifi_password
|
|
|
|
logger:
|
|
api:
|
|
ota:
|
|
|
|
output:
|
|
- platform: esp8266_pwm
|
|
pin: 12
|
|
frequency: 1000 Hz
|
|
id: pwm_b
|
|
- platform: esp8266_pwm
|
|
pin: 13
|
|
frequency: 1000 Hz
|
|
id: pwm_g
|
|
- platform: esp8266_pwm
|
|
pin: 15
|
|
frequency: 1000 Hz
|
|
id: pwm_r
|
|
- platform: esp8266_pwm
|
|
pin: 14
|
|
frequency: 1000 Hz
|
|
id: pwm_w1
|
|
- platform: esp8266_pwm
|
|
pin: 4
|
|
frequency: 1000 Hz
|
|
id: pwm_w2
|
|
light:
|
|
- platform: rgbww
|
|
name: "H801 Light"
|
|
red: pwm_r
|
|
green: pwm_g
|
|
blue: pwm_b
|
|
cold_white: pwm_w1
|
|
warm_white: pwm_w2
|
|
|
|
For :doc:`RGBW </components/light/rgbw>` lights, the ``pwm_w2`` output is not used (and can be removed):
|
|
|
|
.. code-block:: yaml
|
|
|
|
light:
|
|
- platform: rgbw
|
|
name: "H801 Light"
|
|
red: pwm_r
|
|
green: pwm_g
|
|
blue: pwm_b
|
|
white: pwm_w1
|
|
|
|
Flashing
|
|
--------
|
|
|
|
Make your node in the ESPHome dashboard and compile/upload it.
|
|
(if it fails OTA it must be uploaded manually with your favorite ESP flasher,
|
|
e.g. :ref:`esphome-flasher <esphome-flasher>`)
|
|
|
|
You will need to solder pins to the board inside the H801 (fortunately it's pretty roomy and
|
|
not a lot of components or stuff in the way apart from the 2 wires on the back).
|
|
|
|
3.3V, GND, TX and RX (RX to RX and TX to TX) needs to be connected to your serial adapter, the
|
|
two other pins must be shorted throughout the flashing process by a jumper or a breadboard cable.
|
|
(Remember to remove it after flashing)
|
|
|
|
.. figure:: images/h801-board-front.jpg
|
|
:align: center
|
|
:width: 80.0%
|
|
|
|
Front side of board with pins soldered on
|
|
|
|
.. figure:: images/h801-board-back.jpg
|
|
:align: center
|
|
:width: 80.0%
|
|
|
|
Back side of the board (don't melt the blue and red wire when soldering)
|
|
|
|
Add A PIR(Motion) Sensor
|
|
------------------------
|
|
|
|
It's possible to use the header that was soldered on for flashing as an input.
|
|
The example below uses the TX pin as a PIR motion sensor input:
|
|
|
|
.. figure:: images/h801-pir_sensor.jpg
|
|
:align: center
|
|
:width: 80.0%
|
|
|
|
H801 shown with PIR connected to header pins
|
|
|
|
The following can be appended to the YAML file for your H801 to configure the TX pin as a motion
|
|
sensor input.
|
|
|
|
.. code-block:: yaml
|
|
|
|
binary_sensor:
|
|
- platform: gpio
|
|
pin: GPIO3
|
|
name: "GPIO3-TX Motion"
|
|
device_class: motion
|
|
|
|
Pinout
|
|
------
|
|
|
|
.. list-table::
|
|
:header-rows: 1
|
|
|
|
* - Function
|
|
- ESP Pin
|
|
* - R (PWM1)
|
|
- GPIO15
|
|
* - G (PWM2)
|
|
- GPIO13
|
|
* - B (PWM3)
|
|
- GPIO12
|
|
* - W1 (PWM4)
|
|
- GPIO14
|
|
* - W2 (PWM5)
|
|
- GPIO4
|
|
* - Jumper J3
|
|
- GPIO0
|
|
* - RX
|
|
- GPIO2
|
|
* - TX
|
|
- GPIO3
|
|
* - LED D1 (red)
|
|
- GPIO5
|
|
* - LED D2 (green)
|
|
- GPIO1
|
|
|
|
See Also
|
|
--------
|
|
|
|
- :doc:`/components/light/rgb`
|
|
- :doc:`/components/light/rgbw`
|
|
- :doc:`/components/light/rgbww`
|
|
- :doc:`/components/light/rgbct`
|
|
- :doc:`/components/light/monochromatic`
|
|
- :doc:`/components/output/esp8266_pwm`
|
|
- :ghedit:`Edit`
|