mirror of
https://github.com/esphome/esphome-docs.git
synced 2024-12-27 17:37:45 +01:00
80 lines
2.6 KiB
ReStructuredText
80 lines
2.6 KiB
ReStructuredText
MCP2515
|
|
=======
|
|
|
|
.. seo::
|
|
:description: Instructions for setting up the MCP2515 CAN bus platform in ESPHome
|
|
:image: canbus.svg
|
|
:keywords: CAN, MCP2515
|
|
|
|
The MCP2515 communicates with ESPHome via the :ref:`SPI bus <spi>`; to use it, you must have at least one
|
|
:ref:`SPI bus <spi>` with both the ``mosi_pin`` and ``miso_pin`` defined in your ESPHome configuration.
|
|
|
|
The :ref:`mcp2515-wiring` section below illustrates how to wire up your MCP2515.
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Example configuration entry
|
|
canbus:
|
|
- platform: mcp2515
|
|
cs_pin: GPIOXX
|
|
can_id: 4
|
|
bit_rate: 50kbps
|
|
on_frame:
|
|
- can_id: 500
|
|
then:
|
|
- lambda: |-
|
|
std::string b(x.begin(), x.end());
|
|
ESP_LOGD("canid 500", "%s", &b[0] );
|
|
- light.turn_off: light_1
|
|
- can_id: 501
|
|
then:
|
|
- light.turn_on:
|
|
id: light_1
|
|
brightness: !lambda "return (x.size() > 0) ? (float) x[0]/255 : 0;"
|
|
|
|
Configuration variables:
|
|
------------------------
|
|
|
|
- **cs_pin** (**Required**, :ref:`Pin Schema <config-pin_schema>`): Is used to signal to a SPI device when it should
|
|
listen for data on the SPI bus. Each SPI device has its own ``CS`` line. Sometimes also called ``SS``.
|
|
- **clock** (*Optional*, frequency): The frequency of the clock crystal used on the MCP2515 device. One of ``8MHZ``,
|
|
``12MHz``, ``16MHZ`` or ``20MHZ``. Defaults to ``8MHZ``.
|
|
- **mode** (*Optional*, enum): Operating mode. One of:
|
|
|
|
- ``NORMAL``: Normal operation. *(default)*
|
|
- ``LOOPBACK``: Loopback mode is useful for testing your connections to/from the device.
|
|
- ``LISTENONLY``: Receive data only.
|
|
|
|
- All other options from :ref:`Canbus <config-canbus>`.
|
|
|
|
.. note::
|
|
|
|
Not all combinations of clock and bitrate are supported. An unsupported combination will not be flagged at
|
|
compile time. Check your ESPHome device's logs for a message like ``Invalid frequency/bitrate combination``
|
|
if you suspect this is an issue.
|
|
|
|
.. _mcp2515-wiring:
|
|
|
|
Wiring options
|
|
--------------
|
|
|
|
The easiest approach is to use fully assembled boards and just add one resistor on the MISO line. This runs MOSI, SCK
|
|
and CS out of specification which is rarely a problem.
|
|
|
|
.. figure:: images/canbus_mcp2515_resistor.png
|
|
:align: center
|
|
:target: ../_images/canbus_mcp2515_resistor.png
|
|
|
|
A more complex option is to properly convert the 3.3V and 5V logic levels with a level shifter.
|
|
|
|
.. figure:: images/canbus_mcp2515_txs0108e.png
|
|
:align: center
|
|
:target: ../_images/canbus_mcp2515_txs0108e.png
|
|
|
|
See Also
|
|
--------
|
|
|
|
- :doc:`index`
|
|
- :apiref:`canbus/canbus.h`
|
|
- :ghedit:`Edit`
|