mirror of
https://github.com/esphome/esphome-docs.git
synced 2024-11-14 10:35:27 +01:00
101005f1f1
Co-authored-by: Jesse Hills <3060199+jesserockz@users.noreply.github.com> Co-authored-by: Samuel Sieb <samuel@sieb.net>
72 lines
2.7 KiB
ReStructuredText
72 lines
2.7 KiB
ReStructuredText
MAX31865 Platinum RTD Temperature Sensor
|
|
========================================
|
|
|
|
.. seo::
|
|
:description: Instructions for setting up MAX31865 platinum RTD temperature sensors.
|
|
:image: max31865.jpg
|
|
|
|
The ``max31865`` temperature sensor allows you to use your max31865 RTD
|
|
temperature sensor (`datasheet <https://datasheets.maximintegrated.com/en/ds/MAX31865.pdf>`__) with ESPHome
|
|
|
|
.. figure:: images/max31865-full.jpg
|
|
:align: center
|
|
:width: 50.0%
|
|
|
|
MAX31865 Sensor. Image by `Adafruit`_
|
|
|
|
.. _Adafruit: https://www.adafruit.com/product/3328
|
|
|
|
As the communication with the MAX31865 is done using SPI, you need
|
|
to have an :ref:`spi bus <spi>` in your configuration with both **miso_pin** and **mosi_pin** set.
|
|
|
|
- ``VIN`` connects to 5V (``3V3`` will output 3.3V), or directly connect ``3V3`` to 3.3V
|
|
- ``3Vo`` is not used by ESPHome
|
|
- ``GND`` connects to ground
|
|
- ``CLK`` connects to the SPI **clk_pin**
|
|
- ``SDO`` connects to the SPI **miso_pin**
|
|
- ``SDI`` connects to the SPI **mosi_pin**
|
|
- ``CS`` connects to a free GPIO pin
|
|
- ``RDY`` is not used by ESPHome
|
|
|
|
.. code:: yaml
|
|
|
|
# Example configuration entry
|
|
spi:
|
|
miso_pin: D0
|
|
mosi_pin: D1
|
|
clk_pin: D2
|
|
|
|
sensor:
|
|
- platform: max31865
|
|
name: "Living Room Temperature"
|
|
cs_pin: D3
|
|
reference_resistance: 430 Ω
|
|
rtd_nominal_resistance: 100 Ω
|
|
|
|
Configuration variables:
|
|
------------------------
|
|
|
|
- **name** (**Required**, string): The name for the temperature sensor.
|
|
- **cs_pin** (**Required**, :ref:`Pin Schema <config-pin_schema>`): The Chip Select pin of the SPI interface.
|
|
- **update_interval** (*Optional*, :ref:`config-time`): The interval to check the sensor. Defaults to ``60s``.
|
|
- **reference_resistance** (**Required**, float): Reference resistor on the PCB. Adafruit's PT100 (#3328) uses 430 Ω, their PT1000 (#3648) uses 4300 Ω.
|
|
- **rtd_nominal_resistance** (**Required**, float): Nominal resistance of the RTD at 0°C. PT100 is 100 Ω, PT1000 is 1000 Ω.
|
|
- **mains_filter** (*Optional*, string): The mains power frequency to reject (``50 Hz`` or ``60 Hz``). Defaults to ``60 Hz``.
|
|
- **rtd_wires** (*Optional*, int): The number of RTD wires. Be sure to solder board jumpers to match! Defaults to ``4``.
|
|
- **spi_id** (*Optional*, :ref:`config-id`): Manually specify the ID of the :ref:`SPI Component <spi>` if you want to use multiple SPI buses.
|
|
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID used for code generation.
|
|
- All other options from :ref:`Sensor <config-sensor>`.
|
|
|
|
See Also
|
|
--------
|
|
|
|
- :ref:`sensor-filters`
|
|
- :doc:`dht`
|
|
- :doc:`adc`
|
|
- :doc:`max6675`
|
|
- :doc:`max31855`
|
|
- :doc:`max31856`
|
|
- `MAX31865 Library <https://github.com/adafruit/Adafruit_MAX31865>`__ by `Adafruit <https://www.adafruit.com/>`__
|
|
- :apiref:`max31865/max31865.h`
|
|
- :ghedit:`Edit`
|